- boundaryThe list of boundary IDs from the mesh where this object applies
C++ Type:std::vector<BoundaryName>
Controllable:No
Description:The list of boundary IDs from the mesh where this object applies
- direction_1The primary direction of the layers.
C++ Type:MooseEnum
Controllable:No
Description:The primary direction of the layers.
- direction_2The secondary direction of the layers.
C++ Type:MooseEnum
Controllable:No
Description:The secondary direction of the layers.
- num_layers_1The number of layers in the first direction
C++ Type:unsigned int
Controllable:No
Description:The number of layers in the first direction
- num_layers_2The number of layers in the second direction
C++ Type:unsigned int
Controllable:No
Description:The number of layers in the second direction
- variableThe name of the variable that this boundary condition applies to
C++ Type:std::vector<VariableName>
Unit:(no unit assumed)
Controllable:No
Description:The name of the variable that this boundary condition applies to
PartialSumHeatFluxIntegral2D
Computes a set of partial sums of heat fluxes on a surface.
Description
PartialSumHeatFluxIntegral2D computes a set of partial sums of heat flux. The given surface is divided into a set of layers according to num_layers_2. For each layer within that set, the vertical partial sum is computed: where is the thermal conductivity, is the temperature, and is the surface normal.
Example Input Syntax
[UserObjects<<<{"href": "../../syntax/UserObjects/index.html"}>>>]
[ted]
type = PartialSumHeatFluxIntegral2D<<<{"description": "Computes a set of partial sums of heat fluxes on a surface.", "href": "PartialSumHeatFluxIntegral2D.html"}>>>
variable<<<{"description": "The name of the variable that this boundary condition applies to"}>>> = temp
boundary<<<{"description": "The list of boundary IDs from the mesh where this object applies"}>>> = 100
num_layers_1<<<{"description": "The number of layers in the first direction"}>>> = 6
num_layers_2<<<{"description": "The number of layers in the second direction"}>>> = 7
direction_1<<<{"description": "The primary direction of the layers."}>>> = y
direction_2<<<{"description": "The secondary direction of the layers."}>>> = x
sample_type<<<{"description": "How to sample the layers. 'direct' means get the value of the layer the point falls in directly (or average if that layer has no value). 'interpolate' does a linear interpolation between the two closest layers. 'average' averages the two closest layers."}>>> = direct
[]
[]Input Parameters
- sample_typeinterpolateHow to sample the layers. 'direct' means get the value of the layer the point falls in directly (or average if that layer has no value). 'interpolate' does a linear interpolation between the two closest layers. 'average' averages the two closest layers.
Default:interpolate
C++ Type:MooseEnum
Controllable:No
Description:How to sample the layers. 'direct' means get the value of the layer the point falls in directly (or average if that layer has no value). 'interpolate' does a linear interpolation between the two closest layers. 'average' averages the two closest layers.
- thermal_conductivitythermal_conductivityThe name of the thermal conductivity material property that will be used.
Default:thermal_conductivity
C++ Type:std::string
Controllable:No
Description:The name of the thermal conductivity material property that will be used.
Optional Parameters
- allow_duplicate_execution_on_initialFalseIn the case where this UserObject is depended upon by an initial condition, allow it to be executed twice during the initial setup (once before the IC and again after mesh adaptivity (if applicable).
Default:False
C++ Type:bool
Controllable:No
Description:In the case where this UserObject is depended upon by an initial condition, allow it to be executed twice during the initial setup (once before the IC and again after mesh adaptivity (if applicable).
- execute_onTIMESTEP_ENDThe list of flag(s) indicating when this object should be executed. For a description of each flag, see https://mooseframework.inl.gov/source/interfaces/SetupInterface.html.
Default:TIMESTEP_END
C++ Type:ExecFlagEnum
Controllable:No
Description:The list of flag(s) indicating when this object should be executed. For a description of each flag, see https://mooseframework.inl.gov/source/interfaces/SetupInterface.html.
- execution_order_group0Execution order groups are executed in increasing order (e.g., the lowest number is executed first). Note that negative group numbers may be used to execute groups before the default (0) group. Please refer to the user object documentation for ordering of user object execution within a group.
Default:0
C++ Type:int
Controllable:No
Description:Execution order groups are executed in increasing order (e.g., the lowest number is executed first). Note that negative group numbers may be used to execute groups before the default (0) group. Please refer to the user object documentation for ordering of user object execution within a group.
- force_postauxFalseForces the UserObject to be executed in POSTAUX
Default:False
C++ Type:bool
Controllable:No
Description:Forces the UserObject to be executed in POSTAUX
- force_preauxFalseForces the UserObject to be executed in PREAUX
Default:False
C++ Type:bool
Controllable:No
Description:Forces the UserObject to be executed in PREAUX
- force_preicFalseForces the UserObject to be executed in PREIC during initial setup
Default:False
C++ Type:bool
Controllable:No
Description:Forces the UserObject to be executed in PREIC during initial setup
Execution Scheduling Parameters
- control_tagsAdds user-defined labels for accessing object parameters via control logic.
C++ Type:std::vector<std::string>
Controllable:No
Description:Adds user-defined labels for accessing object parameters via control logic.
- enableTrueSet the enabled status of the MooseObject.
Default:True
C++ Type:bool
Controllable:Yes
Description:Set the enabled status of the MooseObject.
- use_displaced_meshFalseWhether or not this object should use the displaced mesh for computation. Note that in the case this is true but no displacements are provided in the Mesh block the undisplaced mesh will still be used.
Default:False
C++ Type:bool
Controllable:No
Description:Whether or not this object should use the displaced mesh for computation. Note that in the case this is true but no displacements are provided in the Mesh block the undisplaced mesh will still be used.
Advanced Parameters
- prop_getter_suffixAn optional suffix parameter that can be appended to any attempt to retrieve/get material properties. The suffix will be prepended with a '_' character.
C++ Type:MaterialPropertyName
Unit:(no unit assumed)
Controllable:No
Description:An optional suffix parameter that can be appended to any attempt to retrieve/get material properties. The suffix will be prepended with a '_' character.
- use_interpolated_stateFalseFor the old and older state use projected material properties interpolated at the quadrature points. To set up projection use the ProjectedStatefulMaterialStorageAction.
Default:False
C++ Type:bool
Controllable:No
Description:For the old and older state use projected material properties interpolated at the quadrature points. To set up projection use the ProjectedStatefulMaterialStorageAction.