- displacementsThe displacements appropriate for the simulation geometry and coordinate system
C++ Type:std::vector<VariableName>
Controllable:No
Description:The displacements appropriate for the simulation geometry and coordinate system
Compute Finite Strain in Cartesian System
Compute a strain increment and rotation increment for finite strains.
Description
This class is used to compute the strain increment, total strain, and incremental rotation for finite strain problems. The finite strain approach used is the incremental corotational form (Rashid, 1993). This approach computes logarithmic strains and strain increments.
Incremental Configurations
In this form, the generic time increment under consideration is such that (1) The configurations of the material element under consideration at and are denoted by , and , respectively for the previous and the current incremental configurations.
Deformation Gradient Definition
The deformation gradient represents the change in a material element from the reference configuration to the current configuration (Malvern, 1969). In the incremental formulation used in the ComputeFiniteStrain class, the incremental deformation gradient represents the change in the material element from the previous configuration, , to the current configuration, . Mathematically this relationship is given as where is the position vector of materials points in , and is the position vector of materials points in .
commentnote:Incremental vs Total Deformation Gradient
Note that is NOT the deformation gradient, but rather the incremental deformation gradient of with respect to . Thus , where is the total deformation gradient at time .
Following the explanation of this procedure given by Zhang et al. (2018), the incremental deformation gradient can be multiplicatively decomposed into an incremental rotation tensor, , and the incremental right stretch tensor, (2) where is a proper orthogonal rotation tensor and the stretch tensor, , is symmetric and positive definite. The incremental right Cauchy-Green deformation tensor, , can be given in terms of by subsituting Eq. (2) into the definition for from Malvern (1969): (3) where the orthogonal nature of enables the simplification given above. Thus can be computed from as (4) which can be evaluated by performing a spectral decomposition of . Once has been computed, the multiplicative decomposition of the deformation gradient is used to find the incremental rotation tensor and the stretching rate . Following Rashid (1993), the stretching rate tensor can be expressed in terms of the 'incremental' right Cauchy-Green deformation tensor (5)
This incremental streteching rate tensor can then be used as the work conjugate for a stress measure, or used to compute another strain measure. The most computationally expensive part of this procedure is the spectral decomposition of to find . This decomposition can be computed exactly using an Eigensolution, yet an approximation of this can be computed with much lower computational expense using a Taylor expansion procedure. This class provides options to perform this calculation either way, and the Taylor expansion is the default.
Taylor Expansion
The stretching rate tensor and incremental rotation matrix can be approximated using Taylor expansion as Rashid (1993): the approximated stretching rate tensor the approximated rotation matrix with The sign of is set by examining the sign of .
Eigen-Solution
The stretching rate tensor can be calculated by the eigenvalues and eigenvectors of . with being the eigenvalue and matrix being constructed from the corresponding eigenvector. the 'incremental' stretching tensor and thus
Volumetric Locking Correction
In ComputeFiniteStrain, is calculated in the computeStrain method, including a volumetric locking correction of where is the average value for the entire element. The strain increment and the rotation increment are calculated in computeQpStrain(). Once the strain increment is calculated, it is added to the total strain from . The total strain from must then be rotated using the rotation increment.
Example Input File Syntax
The finite strain calculator can be activated in the input file through the use of the TensorMechanics Master Action, as shown below.
[./TensorMechanics]
[./Master]
[./all]
strain = FINITE
add_variables = true
[../]
[../]
[../]
commentnote:Use of the Tensor Mechanics Master Action Recommended
The TensorMechanics Master Action is designed to automatically determine and set the strain and stress divergence parameters correctly for the selected strain formulation. We recommend that users employ the TensorMechanics Master Action whenever possible to ensure consistency between the test function gradients and the strain formulation selected.
Although not recommended, it is possible to directly use the ComputeFiniteStrain material in the input file.
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
When directly using ComputeFiniteStrain in an input file as shown above, the StressDivergenceTensors kernel must be modified from the default by setting the parameter use_displaced_mesh = true. This setting is required to maintain consistency in the test function gradients and the strain formulation. For a complete discussion of the stress diveregence kernel settings and the corresponding strain classes, see the section on Consistency Between Stress and Strain in the TensorMechanics module overview. In addition, be aware of the loading cycle limitations while using finite strains as outlined in the section Large Strain Closed Loop Loading Cycle.
Input Parameters
- base_nameOptional parameter that allows the user to define multiple mechanics material systems on the same block, i.e. for multiple phases
C++ Type:std::string
Controllable:No
Description:Optional parameter that allows the user to define multiple mechanics material systems on the same block, i.e. for multiple phases
- blockThe list of blocks (ids or names) that this object will be applied
C++ Type:std::vector<SubdomainName>
Controllable:No
Description:The list of blocks (ids or names) that this object will be applied
- boundaryThe list of boundaries (ids or names) from the mesh where this boundary condition applies
C++ Type:std::vector<BoundaryName>
Controllable:No
Description:The list of boundaries (ids or names) from the mesh where this boundary condition applies
- computeTrueWhen false, MOOSE will not call compute methods on this material. The user must call computeProperties() after retrieving the MaterialBase via MaterialBasePropertyInterface::getMaterialBase(). Non-computed MaterialBases are not sorted for dependencies.
Default:True
C++ Type:bool
Controllable:No
Description:When false, MOOSE will not call compute methods on this material. The user must call computeProperties() after retrieving the MaterialBase via MaterialBasePropertyInterface::getMaterialBase(). Non-computed MaterialBases are not sorted for dependencies.
- constant_onNONEWhen ELEMENT, MOOSE will only call computeQpProperties() for the 0th quadrature point, and then copy that value to the other qps.When SUBDOMAIN, MOOSE will only call computeQpProperties() for the 0th quadrature point, and then copy that value to the other qps. Evaluations on element qps will be skipped
Default:NONE
C++ Type:MooseEnum
Options:NONE, ELEMENT, SUBDOMAIN
Controllable:No
Description:When ELEMENT, MOOSE will only call computeQpProperties() for the 0th quadrature point, and then copy that value to the other qps.When SUBDOMAIN, MOOSE will only call computeQpProperties() for the 0th quadrature point, and then copy that value to the other qps. Evaluations on element qps will be skipped
- declare_suffixAn optional suffix parameter that can be appended to any declared properties. The suffix will be prepended with a '_' character.
C++ Type:MaterialPropertyName
Controllable:No
Description:An optional suffix parameter that can be appended to any declared properties. The suffix will be prepended with a '_' character.
- decomposition_methodTaylorExpansionMethods to calculate the strain and rotation increments
Default:TaylorExpansion
C++ Type:MooseEnum
Options:TaylorExpansion, EigenSolution
Controllable:No
Description:Methods to calculate the strain and rotation increments
- eigenstrain_namesList of eigenstrains to be applied in this strain calculation
C++ Type:std::vector<MaterialPropertyName>
Controllable:No
Description:List of eigenstrains to be applied in this strain calculation
- global_strainOptional material property holding a global strain tensor applied to the mesh as a whole
C++ Type:MaterialPropertyName
Controllable:No
Description:Optional material property holding a global strain tensor applied to the mesh as a whole
- prop_getter_suffixAn optional suffix parameter that can be appended to any attempt to retrieve/get material properties. The suffix will be prepended with a '_' character.
C++ Type:MaterialPropertyName
Controllable:No
Description:An optional suffix parameter that can be appended to any attempt to retrieve/get material properties. The suffix will be prepended with a '_' character.
- volumetric_locking_correctionFalseFlag to correct volumetric locking
Default:False
C++ Type:bool
Controllable:No
Description:Flag to correct volumetric locking
Optional Parameters
- control_tagsAdds user-defined labels for accessing object parameters via control logic.
C++ Type:std::vector<std::string>
Controllable:No
Description:Adds user-defined labels for accessing object parameters via control logic.
- enableTrueSet the enabled status of the MooseObject.
Default:True
C++ Type:bool
Controllable:Yes
Description:Set the enabled status of the MooseObject.
- implicitTrueDetermines whether this object is calculated using an implicit or explicit form
Default:True
C++ Type:bool
Controllable:No
Description:Determines whether this object is calculated using an implicit or explicit form
- seed0The seed for the master random number generator
Default:0
C++ Type:unsigned int
Controllable:No
Description:The seed for the master random number generator
Advanced Parameters
- output_propertiesList of material properties, from this material, to output (outputs must also be defined to an output type)
C++ Type:std::vector<std::string>
Controllable:No
Description:List of material properties, from this material, to output (outputs must also be defined to an output type)
- outputsnone Vector of output names were you would like to restrict the output of variables(s) associated with this object
Default:none
C++ Type:std::vector<OutputName>
Controllable:No
Description:Vector of output names were you would like to restrict the output of variables(s) associated with this object
Outputs Parameters
Input Files
- (modules/fsi/test/tests/fsi_acoustics/1D_struc_acoustic/1D_struc_acoustic.i)
- (modules/contact/test/tests/verification/overclosure_removal/overclosure.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface16.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface14.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/cp_slip_rate_integ/crysp.i)
- (modules/tensor_mechanics/test/tests/multi/two_surface03.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/substep.i)
- (modules/tensor_mechanics/test/tests/capped_mohr_coulomb/random5.i)
- (modules/combined/test/tests/j2_plasticity_vs_LSH/necking/j2_hard1_necking.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/except1.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/crysp_read_slip_prop.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface02.i)
- (modules/tensor_mechanics/test/tests/elem_prop_read_user_object/prop_elem_read.i)
- (modules/contact/test/tests/verification/patch_tests/brick_2/brick2_aug.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/many_deforms_cap.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/except3.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface08.i)
- (modules/tensor_mechanics/test/tests/hyperelastic_viscoplastic/one_elem_linear_harden.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/random_planar.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/save_euler.i)
- (modules/contact/test/tests/pdass_problems/ironing.i)
- (modules/contact/test/tests/mortar_dynamics/block-dynamics-friction.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/except4.i)
- (modules/contact/test/tests/mortar_dynamics/block-dynamics.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface22.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface10.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/planar_hard4.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/planar_hard3.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface20.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/cp_slip_rate_integ/crysp_substep.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface00.i)
- (modules/tensor_mechanics/test/tests/elem_prop_read_user_object/prop_grain_read.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/planar_hard5.i)
- (modules/tensor_mechanics/examples/bridge/bridge_large_strain.i)
- (modules/combined/test/tests/poro_mechanics/borehole_highres.i)
- (modules/contact/test/tests/verification/patch_tests/brick_4/brick4_mu_0_2_pen.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform5.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface05.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/exception.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface15.i)
- (modules/tensor_mechanics/test/tests/multi/two_surface05.i)
- (modules/tensor_mechanics/test/tests/visco/visco_finite_strain.i)
- (modules/combined/test/tests/poro_mechanics/borehole_lowres.i)
- (modules/contact/test/tests/verification/patch_tests/brick_3/brick3_template2.i)
- (modules/contact/test/tests/verification/hertz_cyl/quart_symm_q8/hertz_cyl_qsym_1deg_template1.i)
- (modules/contact/test/tests/mortar_aux_kernels/block-dynamics-aux-vel.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/patch_recovery.i)
- (modules/contact/test/tests/verification/patch_tests/brick_3/brick3_mu_0_2_pen.i)
- (modules/tensor_mechanics/test/tests/ad_elastic/finite_elastic-noad.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform3.i)
- (modules/contact/test/tests/verification/hertz_cyl/quart_symm_q4/hertz_cyl_qsym_1deg_template1.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform_hard_cubic.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface01.i)
- (modules/xfem/test/tests/moving_interface/moving_bimaterial_finite_strain.i)
- (modules/contact/test/tests/glued/glued_contact_mechanical_constraint_test.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/crysp_substep.i)
- (modules/tensor_mechanics/test/tests/multi/special_rock1.i)
- (modules/tensor_mechanics/test/tests/j2_plasticity/small_deform3.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/crysp_user_object.i)
- (modules/combined/test/tests/cavity_pressure/initial_temperature.i)
- (modules/combined/test/tests/cavity_pressure/multiple_postprocessors.i)
- (modules/contact/test/tests/mortar_aux_kernels/block-dynamics-aux-fretting-wear-test.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/user_object_Voce_BCC.i)
- (modules/xfem/test/tests/moving_interface/moving_bimaterial_finite_strain_cut_mesh.i)
- (modules/tensor_mechanics/test/tests/isotropicSD_plasticity/isotropicSD.i)
- (modules/tensor_mechanics/test/tests/action/custom_output.i)
- (modules/contact/test/tests/mortar_aux_kernels/block-dynamics-aux-wear-vel.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/uni_axial1.i)
- (modules/tensor_mechanics/test/tests/stress_recovery/patch/patch_finite_stress.i)
- (modules/tensor_mechanics/test/tests/hyperelastic_viscoplastic/one_elem.i)
- (modules/tensor_mechanics/test/tests/auxkernels/principalstress.i)
- (modules/tensor_mechanics/test/tests/multi/rock1.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/planar3.i)
- (modules/contact/test/tests/pdass_problems/cylinder_friction.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/user_object.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface06.i)
- (modules/xfem/test/tests/moving_interface/moving_bimaterial_finite_strain_esm.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/random.i)
- (modules/contact/test/tests/verification/patch_tests/brick_4/brick4_template1.i)
- (modules/tensor_mechanics/test/tests/initial_stress/mc_tensile.i)
- (modules/tensor_mechanics/test/tests/hyperelastic_viscoplastic/one_elem_base.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/crysp_linesearch.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/except2.i)
- (modules/combined/test/tests/cavity_pressure/additional_volume.i)
- (modules/contact/test/tests/mortar_aux_kernels/block-dynamics-aux-wear.i)
- (modules/tensor_mechanics/test/tests/volumetric_deform_grad/elastic_stress.i)
- (modules/tensor_mechanics/test/tests/multi/two_surface04.i)
- (modules/contact/test/tests/mortar_dynamics/block-dynamics-friction-action.i)
- (modules/fsi/test/tests/fsi_acoustics/3D_struc_acoustic/3D_struc_acoustic.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/crysp.i)
- (modules/tensor_mechanics/test/tests/j2_plasticity/small_deform2.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform1_uo.i)
- (modules/tensor_mechanics/test/tests/finite_strain_tensor_mechanics_tests/finite_strain_patch.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/crysp_fileread.i)
- (modules/tensor_mechanics/test/tests/j2_plasticity/hard1.i)
- (modules/contact/test/tests/verification/patch_tests/brick_1/brick1_template1.i)
- (modules/contact/test/tests/verification/patch_tests/brick_1/brick1_template2.i)
- (modules/tensor_mechanics/test/tests/multi/six_surface14.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/crysp_save_euler.i)
- (modules/tensor_mechanics/test/tests/auxkernels/ranktwoscalaraux.i)
- (modules/combined/test/tests/cavity_pressure/3d.i)
- (modules/tensor_mechanics/test/tests/volumetric_deform_grad/volumetric_strain_interface.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform4.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform_hard2.i)
- (modules/tensor_mechanics/test/tests/drucker_prager/random_hyperbolic.i)
- (modules/tensor_mechanics/test/tests/multi/paper1.i)
- (modules/tensor_mechanics/test/tests/multi/eight_surface14.i)
- (modules/contact/test/tests/verification/hertz_cyl/half_symm_q8/hertz_cyl_half_1deg_template1.i)
- (modules/tensor_mechanics/test/tests/multi/two_surface02.i)
- (modules/contact/test/tests/verification/patch_tests/brick_4/brick4_template2.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface11.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface03.i)
- (modules/tensor_mechanics/test/tests/j2_plasticity/small_deform1.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/fileread.i)
- (modules/contact/test/tests/verification/hertz_cyl/half_symm_q8/hertz_cyl_half_1deg_template3.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface12.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/prop_block_read.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform_hard1.i)
- (modules/tensor_mechanics/test/tests/multi/four_surface14.i)
- (modules/tensor_mechanics/test/tests/elem_prop_read_user_object/prop_grain_read_3d.i)
- (modules/tensor_mechanics/test/tests/multi/two_surface01.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface07.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform2.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform_hard3.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/planar_hard2.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface21.i)
- (modules/contact/test/tests/mortar_dynamics/block-dynamics-action.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/cp_slip_rate_integ/crysp_linesearch.i)
- (modules/tensor_mechanics/test/tests/jacobian_damper/cube_load.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface13.i)
- (modules/tensor_mechanics/test/tests/hyperelastic_viscoplastic/one_elem_multi.i)
- (modules/tensor_mechanics/test/tests/multi/paper3.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface04.i)
- (modules/tensor_mechanics/test/tests/finite_strain_tensor_mechanics_tests/elastic_rotation.i)
- (modules/contact/test/tests/verification/patch_tests/brick_1/brick1_mu_0_2_pen.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform6.i)
- (modules/contact/test/tests/verification/patch_tests/brick_1/brick1_aug.i)
- (modules/tensor_mechanics/test/tests/j2_plasticity/tensor_mechanics_j2plasticity.i)
- (modules/contact/test/tests/verification/patch_tests/brick_2/brick2_template1.i)
- (modules/contact/test/tests/verification/patch_tests/brick_2/brick2_template2.i)
- (modules/tensor_mechanics/test/tests/multi/four_surface24.i)
- (modules/tensor_mechanics/test/tests/multi/three_surface09.i)
- (modules/tensor_mechanics/test/tests/elastic_patch/elastic_patch.i)
- (modules/contact/test/tests/verification/patch_tests/brick_2/brick2_mu_0_2_pen.i)
- (modules/tensor_mechanics/test/tests/mohr_coulomb/planar1.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/use_substep_dt.i)
- (modules/contact/test/tests/verification/hertz_cyl/half_symm_q4/hertz_cyl_half_1deg_template1.i)
- (modules/tensor_mechanics/test/tests/multi/special_joint1.i)
- (modules/contact/test/tests/verification/hertz_cyl/half_symm_q4/hertz_cyl_half_1deg_template3.i)
- (modules/xfem/test/tests/moving_interface/moving_bimaterial_finite_strain_esm_using_cut_mesh.i)
- (modules/tensor_mechanics/test/tests/isotropicSD_plasticity/powerRuleHardening.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/crysp_cutback.i)
- (modules/contact/test/tests/verification/patch_tests/brick_3/brick3_template1.i)
- (modules/combined/test/tests/eigenstrain/variable_finite.i)
- (modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/linesearch.i)
- (modules/tensor_mechanics/test/tests/j2_plasticity/hard2.i)
Child Objects
References
- Lawrence E Malvern.
Introduction to the Mechanics of a Continuous Medium.
Prentice-Hall, 1969.[BibTeX]
@book{malvern1969introduction, author = "Malvern, Lawrence E", title = "Introduction to the Mechanics of a Continuous Medium", year = "1969", publisher = "Prentice-Hall" } - MM Rashid.
Incremental kinematics for finite element applications.
International Journal for Numerical Methods in Engineering, 36(23):3937–3956, 1993.[BibTeX]
@article{rashid1993incremental, author = "Rashid, MM", title = "Incremental kinematics for finite element applications", journal = "International Journal for Numerical Methods in Engineering", volume = "36", number = "23", pages = "3937--3956", year = "1993", publisher = "Wiley Online Library" } - Ziyu Zhang, Wen Jiang, John E Dolbow, and Benjamin W Spencer.
A modified moment-fitted integration scheme for x-fem applications with history-dependent material data.
Computational Mechanics, pages 1–20, 2018.[BibTeX]
@article{zhang2018modified, author = "Zhang, Ziyu and Jiang, Wen and Dolbow, John E and Spencer, Benjamin W", title = "A modified moment-fitted integration scheme for X-FEM applications with history-dependent material data", journal = "Computational Mechanics", pages = "1--20", year = "2018", publisher = "Springer" }
(modules/tensor_mechanics/test/tests/finite_strain_elastic/finite_strain_elastic_new_test.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
[]
[GlobalParams]
displacements = 'disp_x disp_y disp_z'
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = '0.01 * t'
[../]
[]
[Modules]
[./TensorMechanics]
[./Master]
[./all]
strain = FINITE
add_variables = true
[../]
[../]
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = disp_y
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = disp_x
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = disp_z
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_z
boundary = front
function = tdisp
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
C_ijkl = '1.684e5 0.176e5 0.176e5 1.684e5 0.176e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
[../]
[./stress]
type = ComputeFiniteStrainElasticStress
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.05
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomeramg
nl_abs_tol = 1e-10
nl_rel_step_tol = 1e-10
dtmax = 10.0
nl_rel_tol = 1e-10
end_time = 1
dtmin = 0.05
num_steps = 10
nl_abs_step_tol = 1e-10
[]
[Outputs]
exodus = true
[]
(modules/tensor_mechanics/test/tests/volumetric_deform_grad/elastic_stress.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'disp_x disp_y disp_z'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
use_displaced_mesh = true
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = disp_y
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = disp_x
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = disp_z
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_z
boundary = front
function = '0.01*t'
[../]
[]
[Materials]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./elastic_stress]
type = ComputeDeformGradBasedStress
deform_grad_name = deformation_gradient
elasticity_tensor_name = elasticity_tensor
stress_name = stress
jacobian_name = Jacobian_mult
block = 0
[../]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
C_ijkl = '2.8e5 1.2e5 1.2e5 2.8e5 1.2e5 2.8e5 0.8e5 0.8e5 0.8e5'
fill_method = symmetric9
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.02
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_hypre_type -ksp_gmres_restart'
petsc_options_value = 'hypre boomeramg 101'
dtmax = 10.0
nl_rel_tol = 1e-10
dtmin = 0.02
num_steps = 10
[]
[Outputs]
csv = true
[]
(modules/fsi/test/tests/fsi_acoustics/1D_struc_acoustic/1D_struc_acoustic.i)
# Test for `StructureAcousticInterface` interface kernel. The domain is 1D with 20m
# length. The fluid domain is on the right and the structural domain is on the left.
# Fluid end is subjected to a 250Hz sine wave with a single peak of amplitude unity.
# Structural domain is 4 times as dense as the fluid domain with all other material
# properties being the same. Fluid pressure is recorded at the midpoint in the fluid
# domain (i.e., at 15m). Structural stress is recorded at the midpoint in the structural
# domain (i.e., at 5m). The recorded pressure and stress amplitudes should match
# with theoretical values.
#
# Input parameters:
# Dimensions = 1
# Length = 20 meters
# Fluid speed of sound = 1500 m/s
# Fluid density = 1e-6 Giga kg/m^3
# Structural bulk modulus = 2.25 GPa
# Structural shear modulus = 0 GPa
# Structural density = 4e-6 Giga kg/m^3
# Fluid domain = true
# Fluid BC = single peak sine wave applied as a pressure on the fluid end
# Structural domain = true
# Structural BC = Neumann BC with value zero applied on the structural end.
[Mesh]
[gen]
type = GeneratedMeshGenerator
dim = 1
nx = 50
xmax = 20
[]
[./subdomain1]
input = gen
type = SubdomainBoundingBoxGenerator
bottom_left = '10.0 0 0'
block_id = 1
top_right = '20.0 0.0 0'
[../]
[./interface1]
type = SideSetsBetweenSubdomainsGenerator
input = subdomain1
primary_block = '1'
paired_block = 0
new_boundary = 'interface1'
[../]
[]
[GlobalParams]
[]
[Variables]
[./p]
block = 1
[../]
[./disp_x]
block = 0
[../]
[]
[AuxVariables]
[./vel_x]
order = FIRST
family = LAGRANGE
block = 0
[../]
[./accel_x]
order = FIRST
family = LAGRANGE
block = 0
[../]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[Kernels]
[./diffusion]
type = Diffusion
variable = 'p'
block = 1
[../]
[./inertia]
type = AcousticInertia
variable = p
block = 1
[../]
[./DynamicTensorMechanics]
displacements = 'disp_x'
block = 0
[../]
[./inertia_x1]
type = InertialForce
variable = disp_x
block = 0
[../]
[]
[AuxKernels]
[./accel_x]
type = TestNewmarkTI
displacement = disp_x
variable = accel_x
first = false
block = 0
[../]
[./vel_x]
type = TestNewmarkTI
displacement = disp_x
variable = vel_x
block = 0
[../]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
block = 0
[../]
[]
[InterfaceKernels]
[./interface1]
type = StructureAcousticInterface
variable = p
neighbor_var = disp_x
boundary = 'interface1'
D = 1e-6
component = 0
[../]
[]
[BCs]
[./bottom_accel]
type = FunctionDirichletBC
variable = p
boundary = 'right'
function = accel_bottom
[../]
[./disp_x1]
type = NeumannBC
boundary = 'left'
variable = disp_x
value = 0.0
[../]
[]
[Functions]
[./accel_bottom]
type = PiecewiseLinear
data_file = Input_1Peak_highF.csv
scale_factor = 1e-2
format = 'columns'
[../]
[]
[Materials]
[./co_sq]
type = GenericConstantMaterial
prop_names = inv_co_sq
prop_values = 4.44e-7
block = '1'
[../]
[./density0]
type = GenericConstantMaterial
block = 0
prop_names = density
prop_values = 4e-6
[../]
[./elasticity_base]
type = ComputeIsotropicElasticityTensor
bulk_modulus = 2.25
shear_modulus = 0.0
block = 0
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x'
[../]
[./stress]
type = ComputeFiniteStrainElasticStress
block = 0
[../]
[]
[Preconditioning]
[./andy]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
solve_type = 'NEWTON'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_package'
petsc_options_value = 'lu superlu_dist'
start_time = 0.0
end_time = 0.01
dt = 0.0001
dtmin = 0.00001
nl_abs_tol = 1e-12
nl_rel_tol = 1e-12
l_tol = 1e-12
l_max_its = 25
timestep_tolerance = 1e-8
automatic_scaling = true
[TimeIntegrator]
type = NewmarkBeta
[]
[]
[Postprocessors]
[./p1]
type = PointValue
point = '10.0 0.0 0.0'
variable = p
[../]
[./stress1]
type = PointValue
point = '10.0 0.0 0.0'
variable = stress_xx
[../]
[]
[Outputs]
csv = true
exodus = true
perf_graph = true
print_linear_residuals = true
[]
(modules/contact/test/tests/verification/overclosure_removal/overclosure.i)
# ---------------------------------------------------------------------------------------------------------
# REGRESSION TEST FOR OVERCLOSURE REMOVAL
# =======================================
# THIS TEST DEMONSTRATES THAT THE CODE IS CAPABLE OF REMOVING A SIZEABLE OVERCLOSURE IN A SINGLE TIME-STEP
# --------------------------------------------------------------------------------------------------------
[Mesh]
file = oc_mesh.e
[]
[GlobalParams]
volumetric_locking_correction = true
displacements = 'disp_x disp_y'
[]
[Problem]
type = ReferenceResidualProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
order = FIRST
family = LAGRANGE
[../]
[./disp_y]
order = FIRST
family = LAGRANGE
[../]
[]
[AuxVariables]
[./penetration]
order = FIRST
family = LAGRANGE
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y'
extra_vector_tags = 'ref'
use_finite_deform_jacobian = true
[../]
[]
[AuxKernels]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 4
paired_boundary = 3
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./ref_resid_x]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_x
[../]
[./ref_resid_y]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_y
[../]
[./_dt]
type = TimestepSize
[../]
[]
[BCs]
[./bot_y]
type = DirichletBC
variable = disp_y
boundary = 1
value = 0.0
[../]
[./side1_x]
type = DirichletBC
variable = disp_x
boundary = 2
value = 0.0
[../]
[./top_y]
type = DirichletBC
variable = disp_y
boundary = 5
value = 0.0
[../]
[./top_x]
type = DirichletBC
variable = disp_x
boundary = 1001 #nodeset 1001 top central node
value = 0.0
[../]
[]
[Materials]
[./bot_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./bot_strain]
type = ComputeFiniteStrain
decomposition_method = EigenSolution
block = '1'
[../]
[./bot_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./top_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e5
poissons_ratio = 0.3
[../]
[./top_strain]
type = ComputeFiniteStrain
decomposition_method = EigenSolution
block = '2'
[../]
[./top_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-8
nl_rel_tol = 1e-7
l_max_its = 100
nl_max_its = 200
dt = 1.0
end_time = 1.0
dtmin = 1.0
l_tol = 1e-3
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[]
[Contact]
[./leftright]
secondary = 4
primary = 3
model = frictionless
formulation = penalty
normalize_penalty = true
tangential_tolerance = 1e-3
penalty = 1e+9
[../]
[]
(modules/tensor_mechanics/test/tests/multi/three_surface16.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 3
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 3.0E-6m in y direction and 2.1E-6 in z direction.
# trial stress_yy = 3.0 and stress_zz = 2.1
#
# A complicated return will follow, with various contraints being
# deactivated, kuhn-tucker failing, line-searching, etc, but
# the result should be
# stress_yy=1=stress_zz, and internal0=1.1 internal1=2
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '3.0E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '2.1E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 3
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 4
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1 1'
debug_jac_at_intnl = '1 1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface16
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/multi/three_surface14.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 3
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 2.1E-6m in y direction and 3E-6 in z direction.
# trial stress_yy = 2.1 and stress_zz = 3.0
#
# Then all three will be active, but there is linear-dependence.
# SimpleTester1 will turn off, since it is closest,
# and the algorithm will return to stress_zz=1, stress_yy=2, but
# then SimpleTester1 will be positive, so it will be turned back
# on, and then SimpleTester0 or SimpleTester2 will be turned off
# (a random choice will be made).
# If SimpleTester2 is turned
# off then algorithm returns to stress_zz=1=stress_yy, but then
# SimpleTester2 violates Kuhn-Tucker (f<0 and pm>0), so the algorithm
# will restart, and return to stress_zz=1=stress_yy, with internal0=2
# and internal1=1.1
# If SimpleTester0 is turned off then the algorithm will return to
# stress_zz=2, stress_yy=1, where f0>0. Once again, a random choice
# of turning off SimpleTester1 or SimpleTester2 can be made. Hence,
# oscillations can occur. If too many oscillations occur then the algorithm
# will fail
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '2.1E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '3.0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 3
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 4
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1 1'
debug_jac_at_intnl = '1 1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface14
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/cp_slip_rate_integ/crysp.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'disp_x disp_y disp_z'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./e_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./gss1]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./e_zz]
type = RankTwoAux
variable = e_zz
rank_two_tensor = lage
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./gss1]
type = MaterialStdVectorAux
variable = gss1
property = gss
index = 0
execute_on = timestep_end
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = disp_y
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = disp_x
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = disp_z
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_z
boundary = front
function = tdisp
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainCPSlipRateRes
gtol = 1e-2
rtol = 1e-8
abs_tol = 1e-15
slip_sys_file_name = input_slip_sys.txt
nss = 12
num_slip_sys_flowrate_props = 2 #Number of properties in a slip system
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
hprops = '1.0 541.5 60.8 109.8 2.5'
gprops = '1 4 60.8 5 8 60.8 9 12 60.8'
tan_mod_type = exact
slip_incr_tol = 1
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
[../]
[./strain]
type = ComputeFiniteStrain
displacements = 'disp_x disp_y disp_z'
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
[../]
[./e_zz]
type = ElementAverageValue
variable = e_zz
[../]
[./gss1]
type = ElementAverageValue
variable = gss1
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type'
petsc_options_value = 'lu'
dt = 0.2
dtmin = 0.05
dtmax = 10.0
nl_rel_tol = 1e-10
nl_abs_tol = 1e-10
end_time = 1
[]
[Outputs]
file_base = out
exodus = true
print_linear_residuals = true
perf_graph = true
[]
(modules/tensor_mechanics/test/tests/multi/two_surface03.i)
# Plasticit models:
# SimpleTester with a = 0 and b = 1 and strength = 1
# SimpleTester with a = 1 and b = 1 and strength = 2
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 3.0E-6m in z directions and 0.5E-6 in y direction.
# trial stress_zz = 3.0 and stress_yy = 0.5
#
# Then both SimpleTesters should activate initially and return to the "corner" point
# (stress_zz = 1 = stress_yy), but then the plastic multiplier for SimpleTester2 will
# be negative, and so it will be deactivated, and the algorithm will return to
# stress_zz = 1, stress_yy = 0.5
# internal0 should be 2, and internal1 should be 0
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0.5E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '3E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[]
[UserObjects]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 2
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = two_surface03
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/substep.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'ux uy uz'
[]
[Variables]
[./ux]
block = 0
[../]
[./uy]
block = 0
[../]
[./uz]
block = 0
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./e_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./gss]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'ux uy uz'
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./e_zz]
type = RankTwoAux
variable = e_zz
rank_two_tensor = lage
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./gss]
type = MaterialStdVectorAux
variable = gss
property = state_var_gss
index = 0
execute_on = timestep_end
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = uy
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = ux
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = uz
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = uz
boundary = front
function = tdisp
[../]
[]
[UserObjects]
[./slip_rate_gss]
type = CrystalPlasticitySlipRateGSS
variable_size = 12
slip_sys_file_name = input_slip_sys.txt
num_slip_sys_flowrate_props = 2
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
uo_state_var_name = state_var_gss
[../]
[./slip_resistance_gss]
type = CrystalPlasticitySlipResistanceGSS
variable_size = 12
uo_state_var_name = state_var_gss
[../]
[./state_var_gss]
type = CrystalPlasticityStateVariable
variable_size = 12
groups = '0 4 8 12'
group_values = '60.8 60.8 60.8'
uo_state_var_evol_rate_comp_name = state_var_evol_rate_comp_gss
scale_factor = 1.0
[../]
[./state_var_evol_rate_comp_gss]
type = CrystalPlasticityStateVarRateComponentGSS
variable_size = 12
hprops = '1.0 541.5 109.8 2.5'
uo_slip_rate_name = slip_rate_gss
uo_state_var_name = state_var_gss
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainUObasedCP
block = 0
stol = 1e-2
tan_mod_type = exact
maximum_substep_iteration = 10
uo_slip_rates = 'slip_rate_gss'
uo_slip_resistances = 'slip_resistance_gss'
uo_state_vars = 'state_var_gss'
uo_state_var_evol_rate_comps = 'state_var_evol_rate_comp_gss'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'ux uy uz'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
block = 0
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./e_zz]
type = ElementAverageValue
variable = e_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./gss]
type = ElementAverageValue
variable = gss
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 2.0
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
nl_abs_tol = 1e-10
nl_rel_step_tol = 1e-10
dtmax = 10.0
nl_rel_tol = 1e-10
end_time = 30.0
dtmin = 0.5
num_steps = 10
nl_abs_step_tol = 1e-10
[]
[Outputs]
exodus = true
csv = true
gnuplot = true
[]
(modules/tensor_mechanics/test/tests/capped_mohr_coulomb/random5.i)
# Using CappedMohrCoulomb
# Plasticity models:
# Tensile strength = 1.5
# Compressive strength = 3.0
# Cohesion = 1.0
# Friction angle = dilation angle = 20deg
#
# Young = 1, Poisson = 0.3
#
# A line of elements is perturbed randomly, and return to the yield surface at each quadpoint is checked
[Mesh]
type = GeneratedMesh
dim = 3
nx = 100
ny = 12
nz = 1
xmin = 0
xmax = 100
ymin = 0
ymax = 12
zmin = 0
zmax = 1
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[ICs]
[./x]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_x
[../]
[./y]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_y
[../]
[./z]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_z
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0'
[../]
[]
[AuxVariables]
[./Smax]
order = CONSTANT
family = MONOMIAL
[../]
[./Smid]
order = CONSTANT
family = MONOMIAL
[../]
[./Smin]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./Smax]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = Smax
scalar_type = MaxPrincipal
[../]
[./Smid]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = Smid
scalar_type = MidPrincipal
[../]
[./Smin]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = Smin
scalar_type = MinPrincipal
[../]
[]
[UserObjects]
[./ts]
type = TensorMechanicsHardeningConstant
value = 1.5
[../]
[./cs]
type = TensorMechanicsHardeningConstant
value = 3.0
[../]
[./coh]
type = TensorMechanicsHardeningConstant
value = 1.0
[../]
[./phi]
type = TensorMechanicsHardeningConstant
value = 20
convert_to_radians = true
[../]
[./psi]
type = TensorMechanicsHardeningConstant
value = 3
convert_to_radians = true
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeIsotropicElasticityTensor
youngs_modulus = 100
poissons_ratio = 0.3
[../]
[./strain]
type = ComputeFiniteStrain
displacements = 'disp_x disp_y disp_z'
[../]
[./capped_mc]
type = CappedMohrCoulombStressUpdate
tensile_strength = ts
compressive_strength = cs
cohesion = coh
friction_angle = phi
dilation_angle = psi
smoothing_tol = 0.2
yield_function_tol = 1.0E-12
max_NR_iterations = 1000
[../]
[./stress]
type = ComputeMultipleInelasticStress
inelastic_models = capped_mc
perform_finite_strain_rotations = false
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = random5
exodus = true
[]
(modules/combined/test/tests/j2_plasticity_vs_LSH/necking/j2_hard1_necking.i)
#
[Mesh]
file = necking_quad4.e
displacements = 'disp_x disp_y'
[]
[Variables]
[./disp_x]
order = FIRST
family = LAGRANGE
[../]
[./disp_y]
order = FIRST
family = LAGRANGE
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y'
use_displaced_mesh = true
# save_in_disp_x = force_x
save_in_disp_y = force_y
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./strain_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./strain_yy]
order = CONSTANT
family = MONOMIAL
[../]
# [./force_x]
# order = FIRST
# family = LAGRANGE
# [../]
[./force_y]
order = FIRST
family = LAGRANGE
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./strain_xx]
type = RankTwoAux
rank_two_tensor = total_strain
variable = strain_xx
index_i = 0
index_j = 0
[../]
[./strain_yy]
type = RankTwoAux
rank_two_tensor = total_strain
variable = strain_yy
index_i = 1
index_j = 1
[../]
[]
[BCs]
[./left]
type = DirichletBC
variable = disp_x
boundary = left
value = 0.0
[../]
[./bottom]
type = DirichletBC
variable = disp_y
boundary = bottom
value = 0.0
[../]
[./y_top]
type = FunctionDirichletBC
variable = disp_y
boundary = top
function = 't/5'
[../]
[]
[UserObjects]
[./str]
type = TensorMechanicsHardeningConstant
value = 2.4e2
[../]
[./j2]
type = TensorMechanicsPlasticJ2
yield_strength = str
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 1
fill_method = symmetric_isotropic
#with E = 2.1e5 and nu = 0.3
#changed to SM values using E-nu to Lambda-G
C_ijkl = '121154 80769.2'
[../]
[./strain]
type = ComputeFiniteStrain
block = 1
displacements = 'disp_x disp_y'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 1
ep_plastic_tolerance = 1E-9
plastic_models = j2
[../]
[]
[Executioner]
end_time = 0.2
dt = 0.005
type = Transient
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options = '-snes_ksp_ew'
petsc_options_iname = '-ksp_gmres_restart'
petsc_options_value = '101'
line_search = 'none'
l_max_its = 100
nl_max_its = 100
nl_rel_tol = 1e-12
nl_abs_tol = 1e-10
l_tol = 1e-9
[]
[Postprocessors]
[./stress_xx]
type = ElementAverageValue
variable = stress_xx
[../]
[./stress_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./strain_xx]
type = ElementAverageValue
variable = strain_xx
[../]
[./strain_yy]
type = ElementAverageValue
variable = strain_yy
[../]
[./disp_y]
type = NodalSum
variable = disp_y
boundary = top
[../]
[./force_y]
type = NodalSum
variable = force_y
boundary = top
[../]
[]
[Outputs]
exodus = true
csv = true
print_linear_residuals = false
perf_graph = true
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/except1.i)
# checking for exception error messages
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '1E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 10
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 30
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 45
convert_to_radians = true
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 1
mc_edge_smoother = 25
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = mc
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = 1
debug_jac_at_intnl = 1
debug_stress_change = 1E-5
debug_pm_change = 1E-6
debug_intnl_change = 1E-6
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = except1
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/crysp_read_slip_prop.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'ux uy uz'
[]
[Variables]
[./ux]
block = 0
[../]
[./uy]
block = 0
[../]
[./uz]
block = 0
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./rotout]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./e_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./gss1]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'ux uy uz'
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./e_zz]
type = RankTwoAux
variable = e_zz
rank_two_tensor = lage
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./gss1]
type = MaterialStdVectorAux
variable = gss1
property = gss
index = 0
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = uy
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = ux
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = uz
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = uz
boundary = front
function = tdisp
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainCrystalPlasticity
block = 0
gtol = 1e-2
slip_sys_file_name = input_slip_sys_prop.txt
nss = 12
num_slip_sys_flowrate_props = 2 #Number of properties in a slip system
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
hprops = '1.0 541.5 60.8 109.8 2.5'
tan_mod_type = exact
intvar_read_type = slip_sys_file
num_slip_sys_props = 1
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
block = 0
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'ux uy uz'
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./e_zz]
type = ElementAverageValue
variable = e_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./gss1]
type = ElementAverageValue
variable = gss1
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type'
petsc_options_value = 'lu'
nl_rel_tol = 1e-10
nl_abs_tol = 1e-10
dt = 0.05
dtmax = 10.0
dtmin = 0.05
num_steps = 10
[]
[Outputs]
file_base = crysp_read_slip_prop_out
exodus = true
[]
(modules/tensor_mechanics/test/tests/multi/three_surface02.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 1.5
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 0E-6m in y direction and 2.0E-6 in z direction.
# trial stress_yy = 0 and stress_zz = 2.0
#
# Then SimpleTester0 and SimpleTester2 should activate and the algorithm will return to
# the corner stress_yy=0.5, stress_zz=1, but this will require a negative plasticity
# multiplier for SimpleTester2, so it will be deactivated, and the algorithm will return to
# stress_yy = 0, stress_zz = 1
# internal0 should be 1.0, and others zero
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '2.0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 1.5
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface02
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/elem_prop_read_user_object/prop_elem_read.i)
[Mesh]
type = GeneratedMesh
dim = 2
elem_type = QUAD4
displacements = 'disp_x disp_y'
nx = 2
ny = 2
[]
[Variables]
[./disp_x]
block = 0
[../]
[./disp_y]
block = 0
[../]
[]
[GlobalParams]
volumetric_locking_correction=true
[]
[AuxVariables]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./e_yy]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.05*t
[../]
[]
[UserObjects]
[./prop_read]
type = PropertyReadFile
prop_file_name = 'input_file.txt'
# Enter file data as prop#1, prop#2, .., prop#nprop
nprop = 4
read_type = element
[../]
[]
[AuxKernels]
[./stress_yy]
type = RankTwoAux
variable = stress_yy
rank_two_tensor = stress
index_j = 1
index_i = 1
execute_on = timestep_end
block = 0
[../]
[./e_yy]
type = RankTwoAux
variable = e_yy
rank_two_tensor = elastic_strain
index_j = 1
index_i = 1
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./fix_x]
type = DirichletBC
variable = disp_x
boundary = 'left'
value = 0
[../]
[./fix_y]
type = DirichletBC
variable = disp_y
boundary = 'bottom'
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_y
boundary = top
function = tdisp
[../]
[]
[Materials]
[./elasticity_tensor_with_Euler]
type = ComputeElasticityTensorCP
block = 0
C_ijkl = '1.684e5 0.176e5 0.176e5 1.684e5 0.176e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
read_prop_user_object = prop_read
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y'
[../]
[./stress]
type = ComputeFiniteStrainElasticStress
block = 0
[../]
[]
[Postprocessors]
[./stress_yy]
type = ElementAverageValue
variable = stress_yy
block = 'ANY_BLOCK_ID 0'
[../]
[./e_yy]
type = ElementAverageValue
variable = e_yy
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.05
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
nl_abs_tol = 1e-10
nl_rel_step_tol = 1e-10
dtmax = 10.0
nl_rel_tol = 1e-10
end_time = 1
dtmin = 0.05
num_steps = 1
nl_abs_step_tol = 1e-10
[]
[Outputs]
file_base = prop_elem_read_out
exodus = true
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y'
use_displaced_mesh = true
[../]
[]
(modules/contact/test/tests/verification/patch_tests/brick_2/brick2_aug.i)
[GlobalParams]
volumetric_locking_correction = true
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
file = brick2_mesh.e
[]
[Problem]
type = AugmentedLagrangianContactProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
maximum_lagrangian_update_iterations = 100
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./penetration]
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./saved_z]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./diag_saved_z]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./inc_slip_z]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./accum_slip_z]
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y saved_z'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 4
paired_boundary = 3
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./ref_resid_x]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_x
[../]
[./ref_resid_y]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_y
[../]
[./sigma_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./sigma_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./disp_x7]
type = NodalVariableValue
nodeid = 6
variable = disp_x
[../]
[./disp_x26]
type = NodalVariableValue
nodeid = 25
variable = disp_x
[../]
[./disp_y7]
type = NodalVariableValue
nodeid = 6
variable = disp_y
[../]
[./disp_y26]
type = NodalVariableValue
nodeid = 25
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./bot_y]
type = DirichletBC
variable = disp_y
boundary = 1
value = 0.0
[../]
[./side_x]
type = DirichletBC
variable = disp_x
boundary = 2
value = 0.0
[../]
[./back_z]
type = DirichletBC
variable = disp_z
boundary = 6
value = 0.0
[../]
[./top_press]
type = Pressure
variable = disp_y
boundary = 5
factor = 109.89
[../]
[]
[Materials]
[./bot_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./bot_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./bot_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./top_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./top_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./top_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-9
nl_rel_tol = 1e-8
l_max_its = 50
nl_max_its = 100
dt = 1.0
end_time = 1.0
num_steps = 10
dtmin = 1.0
l_tol = 1e-5
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '1 3 4 5'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '1 3 4 5'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
show = 'bot_react_x bot_react_y disp_x7 disp_y7 disp_x26 disp_y26 stress_yy stress_zz top_react_x top_react_y x_disp y_disp cont_press'
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./leftright]
secondary = 3
primary = 4
tangential_tolerance = 1e-3
formulation = augmented_lagrange
normalize_penalty = true
penalty = 1e8
model = frictionless
al_penetration_tolerance = 1e-8
[../]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/many_deforms_cap.i)
# apply many large deformations, checking that the algorithm returns correctly to
# the yield surface each time
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./bottomx]
type = DirichletBC
variable = disp_x
boundary = back
value = 0.0
[../]
[./bottomy]
type = DirichletBC
variable = disp_y
boundary = back
value = 0.0
[../]
[./bottomz]
type = DirichletBC
variable = disp_z
boundary = back
value = 0.0
[../]
[./topx]
type = FunctionDirichletBC
variable = disp_x
boundary = front
function = '(sin(0.05*t)+x)/1E0'
[../]
[./topy]
type = FunctionDirichletBC
variable = disp_y
boundary = front
function = '(cos(0.04*t)+x*y)/1E0'
[../]
[./topz]
type = FunctionDirichletBC
variable = disp_z
boundary = front
function = 't/1E2'
[../]
[]
[AuxVariables]
[./yield_fcn]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./yield_fcn_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn
[../]
[]
[Postprocessors]
[./yield_fcn_at_zero]
type = PointValue
point = '0 0 0'
variable = yield_fcn
outputs = 'console'
[../]
[./should_be_zero]
type = FunctionValuePostprocessor
function = should_be_zero_fcn
[../]
[]
[Functions]
[./should_be_zero_fcn]
type = ParsedFunction
value = 'if(a<1E-3,0,a)'
vars = 'a'
vals = 'yield_fcn_at_zero'
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 1E3
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 30
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 5
convert_to_radians = true
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
tip_scheme = cap
mc_tip_smoother = 0.0
cap_start = 1000
cap_rate = 1E-3
mc_edge_smoother = 10
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-6
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
max_NR_iterations = 1000
ep_plastic_tolerance = 1E-6
plastic_models = mc
debug_fspb = crash
deactivation_scheme = safe
[../]
[]
[Executioner]
end_time = 1000
dt = 1
type = Transient
[]
[Outputs]
file_base = many_deforms_cap
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/except3.i)
# checking for exception error messages on the edge smoothing
# here edge_smoother=5deg, which means the friction_angle must be <= 35.747
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '1E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 10
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 36
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 5
convert_to_radians = true
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 1
mc_edge_smoother = 5
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = mc
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = 1
debug_jac_at_intnl = 1
debug_stress_change = 1E-5
debug_pm_change = 1E-6
debug_intnl_change = 1E-6
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = except3
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/multi/three_surface08.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 1.5
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 2.0E-6m in y direction and 0.5E-6 in z direction.
# trial stress_yy = 2.0 and stress_zz = 0.5
#
# Then SimpleTester1 and SimpleTester2 should activate and the algorithm will return to
# the corner stress_yy=1.0, stress_zz=0.5
# internal1 should be 1.0, and internal2 should be 0
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '2.0E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0.5E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 1.5
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface08
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/hyperelastic_viscoplastic/one_elem_linear_harden.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'ux uy uz'
[]
[Variables]
[./ux]
block = 0
[../]
[./uy]
block = 0
[../]
[./uz]
block = 0
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'ux uy uz'
use_displaced_mesh = true
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./peeq]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./peeq]
type = MaterialRealAux
variable = peeq
property = ep_eqv
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = uy
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = ux
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = uz
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = uz
boundary = front
function = '0.01*t'
[../]
[]
[UserObjects]
[./flowstress]
type = HEVPLinearHardening
yield_stress = 100
slope = 10
intvar_prop_name = ep_eqv
[../]
[./flowrate]
type = HEVPFlowRatePowerLawJ2
reference_flow_rate = 0.0001
flow_rate_exponent = 50.0
flow_rate_tol = 1
strength_prop_name = flowstress
[../]
[./ep_eqv]
type = HEVPEqvPlasticStrain
intvar_rate_prop_name = ep_eqv_rate
[../]
[./ep_eqv_rate]
type = HEVPEqvPlasticStrainRate
flow_rate_prop_name = flowrate
[../]
[]
[Materials]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'ux uy uz'
[../]
[./viscop]
type = FiniteStrainHyperElasticViscoPlastic
block = 0
resid_abs_tol = 1e-18
resid_rel_tol = 1e-8
maxiters = 50
max_substep_iteration = 5
flow_rate_user_objects = 'flowrate'
strength_user_objects = 'flowstress'
internal_var_user_objects = 'ep_eqv'
internal_var_rate_user_objects = 'ep_eqv_rate'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
C_ijkl = '2.8e5 1.2e5 1.2e5 2.8e5 1.2e5 2.8e5 0.8e5 0.8e5 0.8e5'
fill_method = symmetric9
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./peeq]
type = ElementAverageValue
variable = peeq
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.02
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
dtmax = 10.0
nl_rel_tol = 1e-10
dtmin = 0.02
num_steps = 10
[]
[Outputs]
file_base = one_elem_linear_harden
exodus = true
csv = false
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/random_planar.i)
# apply many random large deformations, checking that the algorithm returns correctly to
# the yield surface each time.
[Mesh]
type = GeneratedMesh
dim = 3
nx = 100
ny = 1250
nz = 1
xmin = 0
xmax = 100
ymin = 0
ymax = 1250
zmin = 0
zmax = 1
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[ICs]
[./x]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_x
[../]
[./y]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_y
[../]
[./z]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_z
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0'
[../]
[]
[AuxVariables]
[./yield_fcn]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./yield_fcn_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./yield_fcn_at_zero]
type = PointValue
point = '0 0 0'
variable = yield_fcn
outputs = 'console'
[../]
[./should_be_zero]
type = FunctionValuePostprocessor
function = should_be_zero_fcn
[../]
[./av_iter]
type = ElementAverageValue
variable = iter
outputs = 'console'
[../]
[]
[Functions]
[./should_be_zero_fcn]
type = ParsedFunction
value = 'if(a<1E-3,0,a)'
vars = 'a'
vals = 'yield_fcn_at_zero'
[../]
[]
[UserObjects]
[./coh]
type = TensorMechanicsHardeningCubic
value_0 = 1000
value_residual = 100
internal_limit = 4
[../]
[./phi]
type = TensorMechanicsHardeningCubic
value_0 = 0.8
value_residual = 0.3
internal_limit = 2
[../]
[./psi]
type = TensorMechanicsHardeningConstant
value = 15
convert_to_radians = true
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulombMulti
cohesion = coh
friction_angle = phi
dilation_angle = psi
yield_function_tolerance = 1E-3
shift = 1E-10
internal_constraint_tolerance = 1E-6
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0.7E7 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-10
plastic_models = mc
min_stepsize = 1
max_stepsize_for_dumb = 1
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = random_planar
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/save_euler.i)
[Mesh]
type = GeneratedMesh
dim = 2
elem_type = QUAD4
displacements = 'disp_x disp_y'
nx = 2
ny = 2
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[]
[GlobalParams]
volumetric_locking_correction = true
[]
[AuxVariables]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./e_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./fp_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./gss]
order = CONSTANT
family = MONOMIAL
[../]
[./euler1]
order = CONSTANT
family = MONOMIAL
[../]
[./euler2]
order = CONSTANT
family = MONOMIAL
[../]
[./euler3]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[UserObjects]
[./prop_read]
type = PropertyReadFile
prop_file_name = 'euler_ang_file.txt'
# Enter file data as prop#1, prop#2, .., prop#nprop
nprop = 3
read_type = element
[../]
[]
[AuxKernels]
[./stress_yy]
type = RankTwoAux
variable = stress_yy
rank_two_tensor = stress
index_j = 1
index_i = 1
execute_on = timestep_end
[../]
[./e_yy]
type = RankTwoAux
variable = e_yy
rank_two_tensor = lage
index_j = 1
index_i = 1
execute_on = timestep_end
[../]
[./fp_yy]
type = RankTwoAux
variable = fp_yy
rank_two_tensor = fp
index_j = 1
index_i = 1
execute_on = timestep_end
[../]
[./gss]
type = MaterialStdVectorAux
variable = gss
property = state_var_gss
index = 0
execute_on = timestep_end
[../]
[./euler1]
type = MaterialRealVectorValueAux
variable = euler1
property = Euler_angles
component = 0
execute_on = timestep_end
[../]
[./euler2]
type = MaterialRealVectorValueAux
variable = euler2
property = Euler_angles
component = 1
execute_on = timestep_end
[../]
[./euler3]
type = MaterialRealVectorValueAux
variable = euler3
property = Euler_angles
component = 2
execute_on = timestep_end
[../]
[]
[BCs]
[./fix_x]
type = DirichletBC
variable = disp_x
boundary = 'left'
value = 0
[../]
[./fix_y]
type = DirichletBC
variable = disp_y
boundary = 'bottom'
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_y
boundary = top
function = tdisp
[../]
[]
[UserObjects]
[./slip_rate_gss]
type = CrystalPlasticitySlipRateGSS
variable_size = 12
slip_sys_file_name = input_slip_sys.txt
num_slip_sys_flowrate_props = 2
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
uo_state_var_name = state_var_gss
[../]
[./slip_resistance_gss]
type = CrystalPlasticitySlipResistanceGSS
variable_size = 12
uo_state_var_name = state_var_gss
[../]
[./state_var_gss]
type = CrystalPlasticityStateVariable
variable_size = 12
groups = '0 4 8 12'
group_values = '60.8 60.8 60.8'
uo_state_var_evol_rate_comp_name = state_var_evol_rate_comp_gss
scale_factor = 1.0
[../]
[./state_var_evol_rate_comp_gss]
type = CrystalPlasticityStateVarRateComponentGSS
variable_size = 12
hprops = '1.0 541.5 109.8 2.5'
uo_slip_rate_name = slip_rate_gss
uo_state_var_name = state_var_gss
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainUObasedCP
stol = 1e-2
tan_mod_type = exact
uo_slip_rates = 'slip_rate_gss'
uo_slip_resistances = 'slip_resistance_gss'
uo_state_vars = 'state_var_gss'
uo_state_var_evol_rate_comps = 'state_var_evol_rate_comp_gss'
[../]
[./strain]
type = ComputeFiniteStrain
displacements = 'disp_x disp_y'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
read_prop_user_object = prop_read
[../]
[]
[Postprocessors]
[./stress_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./e_yy]
type = ElementAverageValue
variable = e_yy
[../]
[./fp_yy]
type = ElementAverageValue
variable = fp_yy
[../]
[./gss]
type = ElementAverageValue
variable = gss
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.01
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
nl_abs_tol = 1e-10
nl_rel_step_tol = 1e-10
dtmax = 10.0
nl_rel_tol = 1e-10
end_time = 1
dtmin = 0.01
num_steps = 10
nl_abs_step_tol = 1e-10
[]
[Outputs]
exodus = true
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y'
use_displaced_mesh = true
[../]
[]
(modules/contact/test/tests/pdass_problems/ironing.i)
[GlobalParams]
volumetric_locking_correction = true
displacements = 'disp_x disp_y'
[]
[Mesh]
[input_file]
type = FileMeshGenerator
file = iron.e
[]
[secondary]
type = LowerDBlockFromSidesetGenerator
new_block_id = 10001
new_block_name = 'secondary_lower'
sidesets = '10'
input = input_file
[]
[primary]
type = LowerDBlockFromSidesetGenerator
new_block_id = 10000
sidesets = '20'
new_block_name = 'primary_lower'
input = secondary
[]
patch_update_strategy = auto
patch_size = 20
[]
[Variables]
[disp_x]
[]
[disp_y]
[]
[frictionless_normal_lm]
order = FIRST
family = LAGRANGE
block = 'secondary_lower'
use_dual = true
[]
[tangential_lm]
order = FIRST
family = LAGRANGE
block = 'secondary_lower'
use_dual = true
[]
[]
[AuxVariables]
[stress_xx]
order = CONSTANT
family = MONOMIAL
[]
[stress_yy]
order = CONSTANT
family = MONOMIAL
[]
[stress_xy]
order = CONSTANT
family = MONOMIAL
[]
[saved_x]
[]
[saved_y]
[]
[diag_saved_x]
[]
[diag_saved_y]
[]
[von_mises]
order = CONSTANT
family = MONOMIAL
[]
[]
[Functions]
[disp_ramp_vert]
type = PiecewiseLinear
x = '0. 2. 8.'
y = '0. -1.0 -1.0'
[]
[disp_ramp_horz]
type = PiecewiseLinear
x = '0. 8.' # x = '0. 2. 8.'
y = '0. 8.' # y = '0. 0. 8'
[]
[]
[Kernels]
[TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y'
block = '1 2'
strain = FINITE
[]
[]
[AuxKernels]
[stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
block = '1 2'
[]
[stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
block = '1 2'
[]
[stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
block = '1 2'
[]
[von_mises_kernel]
#Calculates the von mises stress and assigns it to von_mises
type = RankTwoScalarAux
variable = von_mises
rank_two_tensor = stress
execute_on = timestep_end
scalar_type = VonMisesStress
block = '1 2'
[]
[]
[Postprocessors]
[bot_react_x]
type = NodalSum
variable = saved_x
boundary = 20
[]
[bot_react_y]
type = NodalSum
variable = saved_y
boundary = 20
[]
[top_react_x]
type = NodalSum
variable = saved_x
boundary = 10
[]
[top_react_y]
type = NodalSum
variable = saved_y
boundary = 10
[]
[_dt]
type = TimestepSize
[]
[contact_pressure]
type = NodalVariableValue
variable = frictionless_normal_lm
nodeid = 805
[]
[]
[BCs]
[bot_x_disp]
type = DirichletBC
variable = disp_x
boundary = '40'
value = 0.0
preset = false
[]
[bot_y_disp]
type = DirichletBC
variable = disp_y
boundary = '40'
value = 0.0
preset = false
[]
[top_y_disp]
type = FunctionDirichletBC
variable = disp_y
boundary = '30'
function = disp_ramp_vert
preset = false
[]
[top_x_disp]
type = FunctionDirichletBC
variable = disp_x
boundary = '30'
function = disp_ramp_horz
preset = false
[]
[]
[Materials]
[stuff1_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 6896
poissons_ratio = 0.32
[]
[stuff1_strain]
type = ComputeFiniteStrain
block = '2'
[]
[stuff1_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[]
[stuff2_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 689.6
poissons_ratio = 0.32
[]
[stuff2_strain]
type = ComputeFiniteStrain
block = '1'
[]
[stuff2_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options = '-snes_ksp_ew'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-7
nl_rel_tol = 1e-7
l_tol = 1e-6
l_max_its = 50
nl_max_its = 30
start_time = 0.0
end_time = 0.1 # 6.5
dt = 0.0125
dtmin = 1e-5
[]
[Preconditioning]
[SMP]
type = SMP
full = true
[]
[]
[VectorPostprocessors]
[cont_press]
type = NodalValueSampler
variable = frictionless_normal_lm
boundary = '10'
sort_by = id
execute_on = FINAL
[]
[friction]
type = NodalValueSampler
variable = tangential_lm
boundary = '10'
sort_by = id
execute_on = FINAL
[]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
exodus = false
csv = true
[chkfile]
type = CSV
show = 'cont_press friction'
start_time = 0.0
execute_vector_postprocessors_on = FINAL
[]
[console]
type = Console
max_rows = 5
[]
[]
[Debug]
show_var_residual_norms = true
[]
[Constraints]
# All constraints below for mechanical contact (Mortar)
[weighted_gap_lm]
type = ComputeFrictionalForceLMMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 10000
secondary_subdomain = 10001
variable = frictionless_normal_lm
disp_x = disp_x
disp_y = disp_y
use_displaced_mesh = true
friction_lm = tangential_lm
mu = 0.5
c_t = 1.0e1
c = 1.0e3
[]
[x]
type = NormalMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = '10000'
secondary_subdomain = '10001'
variable = frictionless_normal_lm
secondary_variable = disp_x
component = x
use_displaced_mesh = true
compute_lm_residuals = false
[]
[y]
type = NormalMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = '10000'
secondary_subdomain = '10001'
variable = frictionless_normal_lm
secondary_variable = disp_y
component = y
use_displaced_mesh = true
compute_lm_residuals = false
[]
[tangential_x]
type = TangentialMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = '10000'
secondary_subdomain = '10001'
variable = tangential_lm
secondary_variable = disp_x
component = x
use_displaced_mesh = true
compute_lm_residuals = false
[]
[tangential_y]
type = TangentialMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = '10000'
secondary_subdomain = '10001'
variable = tangential_lm
secondary_variable = disp_y
component = y
use_displaced_mesh = true
compute_lm_residuals = false
[]
[]
(modules/contact/test/tests/mortar_dynamics/block-dynamics-friction.i)
starting_point = 2e-1
offset = -0.19
[GlobalParams]
displacements = 'disp_x disp_y'
[]
[Mesh]
file = long-bottom-block-1elem-blocks.e
allow_renumbering = false
[]
[Variables]
[disp_x]
block = '1 2'
[]
[disp_y]
block = '1 2'
[]
[mechanical_normal_lm]
block = 3
use_dual = true
[]
[mechanical_tangential_lm]
block = 3
use_dual = true
[]
[]
[ICs]
[disp_y]
block = 2
variable = disp_y
value = '${fparse starting_point + offset}'
type = ConstantIC
[]
[]
[Kernels]
[DynamicTensorMechanics]
displacements = 'disp_x disp_y'
generate_output = 'stress_xx stress_yy'
strain = FINITE
block = '1 2'
stiffness_damping_coefficient = 0.05
hht_alpha = 0.0
[]
[inertia_x]
type = InertialForce
variable = disp_x
velocity = vel_x
acceleration = accel_x
beta = 0.25
gamma = 0.5
alpha = 0
eta = 0.0
block = '1 2'
[]
[inertia_y]
type = InertialForce
variable = disp_y
velocity = vel_y
acceleration = accel_y
beta = 0.25
gamma = 0.5
alpha = 0
eta = 0.0
block = '1 2'
[]
[]
[Materials]
[elasticity_2]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[]
[elasticity_1]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e8
poissons_ratio = 0.3
[]
[stress]
type = ComputeFiniteStrainElasticStress
block = '1 2'
[]
[strain]
type = ComputeFiniteStrain
block = '1 2'
[]
[density]
type = GenericConstantMaterial
block = '1 2'
prop_names = 'density'
prop_values = '7750'
[]
[]
[AuxVariables]
[vel_x]
block = '1 2'
[]
[accel_x]
block = '1 2'
[]
[vel_y]
block = '1 2'
[]
[accel_y]
block = '1 2'
[]
[vel_z]
block = '1 2'
[]
[accel_z]
block = '1 2'
[]
[gap]
block = 3
[]
[]
[AuxKernels]
[gap]
type = WeightedGapAux
variable = gap
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
use_displaced_mesh = true
[]
[accel_x]
type = NewmarkAccelAux
variable = accel_x
displacement = disp_x
velocity = vel_x
beta = 0.25
execute_on = 'LINEAR timestep_end'
[]
[vel_x]
type = NewmarkVelAux
variable = vel_x
acceleration = accel_x
gamma = 0.5
execute_on = 'LINEAR timestep_end'
[]
[accel_y]
type = NewmarkAccelAux
variable = accel_y
displacement = disp_y
velocity = vel_y
beta = 0.25
execute_on = 'LINEAR timestep_end'
[]
[vel_y]
type = NewmarkVelAux
variable = vel_y
acceleration = accel_y
gamma = 0.5
execute_on = 'LINEAR timestep_end'
[]
[]
[Constraints]
[weighted_gap_lm]
type = ComputeDynamicFrictionalForceLMMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = mechanical_normal_lm
friction_lm = mechanical_tangential_lm
disp_x = disp_x
disp_y = disp_y
use_displaced_mesh = true
c = 1e4
c_t = 1e4
mu = 0.5
interpolate_normals = false
newmark_beta = 0.25
newmark_gamma = 0.5
capture_tolerance = 1.0e-3
[]
[normal_x]
type = NormalMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = mechanical_normal_lm
secondary_variable = disp_x
component = x
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[normal_y]
type = NormalMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = mechanical_normal_lm
secondary_variable = disp_y
component = y
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[tangential_x]
type = TangentialMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = mechanical_tangential_lm
secondary_variable = disp_x
component = x
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[tangential_y]
type = TangentialMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = mechanical_tangential_lm
secondary_variable = disp_y
component = y
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[]
[BCs]
[botx]
type = DirichletBC
variable = disp_x
boundary = 40
value = 0.0
[]
[boty]
type = DirichletBC
variable = disp_y
boundary = 40
value = 0.0
[]
[topy]
type = FunctionDirichletBC
variable = disp_y
boundary = 30
function = '${starting_point} * cos(2 * pi / 4 * t) + ${offset}'
[]
[leftx]
type = FunctionDirichletBC
variable = disp_x
boundary = 30 # 50
function = '0' # '1e-2*t'
[]
[]
[Executioner]
type = Transient
end_time = 75
dt = 0.05
dtmin = .005
solve_type = 'PJFNK'
petsc_options = '-snes_converged_reason -ksp_converged_reason -pc_svd_monitor '
'-snes_linesearch_monitor -snes_ksp_ew'
petsc_options_iname = '-pc_type -pc_factor_shift_type -pc_factor_shift_amount -mat_mffd_err '
petsc_options_value = 'lu NONZERO 1e-15 1e-5'
nl_max_its = 50
line_search = 'none'
snesmf_reuse_base = false
[TimeIntegrator]
type = NewmarkBeta
beta = 0.25
gamma = 0.5
[]
[]
[Debug]
show_var_residual_norms = true
[]
[Outputs]
exodus = true
csv = true
checkpoint = true
[]
[Preconditioning]
[smp]
type = SMP
full = true
[]
[]
[VectorPostprocessors]
[mechanical_tangential_lm]
type = NodalValueSampler
block = '3'
variable = mechanical_tangential_lm
sort_by = 'x'
execute_on = TIMESTEP_END
[]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/except4.i)
# checking for exception error messages on the edge smoothing
# here edge_smoother=5deg, which means the friction_angle must be <= 35.747
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '1E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 10
[../]
[./mc_phi]
type = TensorMechanicsHardeningExponential
value_0 = 0.52359878 # 30deg
value_residual = 0.62831853 # 36deg
rate = 3000.0
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 5
convert_to_radians = true
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 1
mc_edge_smoother = 5
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = mc
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = 1
debug_jac_at_intnl = 1
debug_stress_change = 1E-5
debug_pm_change = 1E-6
debug_intnl_change = 1E-6
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = except4
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/contact/test/tests/mortar_dynamics/block-dynamics.i)
starting_point = 2e-1
offset = -0.19
[GlobalParams]
displacements = 'disp_x disp_y'
[]
[Mesh]
file = long-bottom-block-1elem-blocks.e
[]
[Variables]
[disp_x]
block = '1 2'
[]
[disp_y]
block = '1 2'
[]
[normal_lm]
block = 3
use_dual = true
[]
[]
[ICs]
[disp_y]
block = 2
variable = disp_y
value = '${fparse starting_point + offset}'
type = ConstantIC
[]
[]
[Kernels]
[DynamicTensorMechanics]
displacements = 'disp_x disp_y'
generate_output = 'stress_xx stress_yy'
strain = FINITE
block = '1 2'
zeta = 1.0
alpha = 0.0
[]
[inertia_x]
type = InertialForce
variable = disp_x
velocity = vel_x
acceleration = accel_x
beta = 0.25
gamma = 0.5
alpha = 0
eta = 0.0
block = '1 2'
[]
[inertia_y]
type = InertialForce
variable = disp_y
velocity = vel_y
acceleration = accel_y
beta = 0.25
gamma = 0.5
alpha = 0
eta = 0.0
block = '1 2'
[]
[]
[Materials]
[elasticity_2]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[]
[elasticity_1]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e8
poissons_ratio = 0.3
[]
[stress]
type = ComputeFiniteStrainElasticStress
block = '1 2'
[]
[strain]
type = ComputeFiniteStrain
block = '1 2'
[]
[density]
type = GenericConstantMaterial
block = '1 2'
prop_names = 'density'
prop_values = '7750'
[]
[]
[AuxVariables]
[vel_x]
block = '1 2'
[]
[accel_x]
block = '1 2'
[]
[vel_y]
block = '1 2'
[]
[accel_y]
block = '1 2'
[]
[vel_z]
block = '1 2'
[]
[accel_z]
block = '1 2'
[]
[]
[AuxKernels]
[accel_x]
type = NewmarkAccelAux
variable = accel_x
displacement = disp_x
velocity = vel_x
beta = 0.25
execute_on = 'LINEAR timestep_end'
[]
[vel_x]
type = NewmarkVelAux
variable = vel_x
acceleration = accel_x
gamma = 0.5
execute_on = 'LINEAR timestep_end'
[]
[accel_y]
type = NewmarkAccelAux
variable = accel_y
displacement = disp_y
velocity = vel_y
beta = 0.25
execute_on = 'LINEAR timestep_end'
[]
[vel_y]
type = NewmarkVelAux
variable = vel_y
acceleration = accel_y
gamma = 0.5
execute_on = 'LINEAR timestep_end'
[]
[]
[Constraints]
[weighted_gap_lm]
type = ComputeDynamicWeightedGapLMMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = normal_lm
disp_x = disp_x
disp_y = disp_y
use_displaced_mesh = true
c = 1e4
interpolate_normals = false
capture_tolerance = 1.0e-5
newmark_beta = 0.25
newmark_gamma = 0.5
[]
[normal_x]
type = NormalMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = normal_lm
secondary_variable = disp_x
component = x
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[normal_y]
type = NormalMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = normal_lm
secondary_variable = disp_y
component = y
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[]
[BCs]
[botx]
type = DirichletBC
variable = disp_x
boundary = 40
value = 0.0
[]
[boty]
type = DirichletBC
variable = disp_y
boundary = 40
value = 0.0
[]
[topy]
type = FunctionDirichletBC
variable = disp_y
boundary = 30
function = '${starting_point} * cos(2 * pi / 4 * t) + ${offset}'
[]
[leftx]
type = FunctionDirichletBC
variable = disp_x
boundary = 50
function = '1e-2 * t'
[]
[]
[Executioner]
type = Transient
end_time = 75
dt = 0.05
dtmin = .05
solve_type = 'PJFNK'
petsc_options = '-snes_converged_reason -ksp_converged_reason -pc_svd_monitor '
'-snes_linesearch_monitor -snes_ksp_ew'
petsc_options_iname = '-pc_type -pc_factor_shift_type -pc_factor_shift_amount -mat_mffd_err '
petsc_options_value = 'lu NONZERO 1e-15 1e-5'
nl_max_its = 20
line_search = 'none'
snesmf_reuse_base = false
[TimeIntegrator]
type = NewmarkBeta
beta = 0.25
gamma = 0.5
[]
[]
[Debug]
show_var_residual_norms = true
[]
[Outputs]
exodus = true
checkpoint = true
[]
[Preconditioning]
[smp]
type = SMP
full = true
[]
[]
[Postprocessors]
active = 'num_nl cumulative contact'
[num_nl]
type = NumNonlinearIterations
[]
[cumulative]
type = CumulativeValuePostprocessor
postprocessor = num_nl
[]
[contact]
type = ContactDOFSetSize
variable = normal_lm
subdomain = '3'
execute_on = 'nonlinear timestep_end'
[]
[]
(modules/tensor_mechanics/test/tests/multi/three_surface22.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 1.5
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 1.7E-6m in y direction and 1.1E-6 in z direction.
# trial stress_yy = 1.7 and stress_zz = 1.1
#
# Then all yield functions will activate
# However, there is linear dependence. SimpleTester0 will be rutned off.
# The algorithm will return to
# stress_yy=1.0 and stress_zz=0.5
# internal1=0.1, internal2=0.6
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1.7E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1.1E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 1.5
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface22
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/multi/three_surface10.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 1.5
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 1.5E-6m in y direction and 0.0E-6 in z direction.
# trial stress_yy = 1.5 and stress_zz = 0.0
#
# Then SimpleTester1 should activate and the algorithm will return to
# stress_yy=1
# internal1 should be 0.5
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1.5E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0.0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 1.5
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface10
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/planar_hard4.i)
# apply repeated stretches in x direction, and smaller stretches along the y and z directions,
# so that sigma_II = sigma_III,
# which means that lode angle = -30deg.
# Both return to the edge (at lode_angle=-30deg, ie 000101) and tip are experienced.
#
# It is checked that the yield functions are less than their tolerance values
# It is checked that the cohesion hardens correctly
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0.05E-6*x*t'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0.05E-6*y*t'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z*t'
[../]
[]
[Functions]
[./should_be_zero_fcn]
type = ParsedFunction
value = 'if((a<1E-5)&(b<1E-5)&(c<1E-5)&(d<1E-5)&(g<1E-5)&(h<1E-5),0,abs(a)+abs(b)+abs(c)+abs(d)+abs(g)+abs(h))'
vars = 'a b c d g h'
vals = 'f0 f1 f2 f3 f4 f5'
[../]
[./coh_analytic]
type = ParsedFunction
value = '20-10*exp(-1E5*intnl)'
vars = intnl
vals = internal
[../]
[./coh_from_yieldfcns]
type = ParsedFunction
value = '(f0+f1-(sxx+syy)*sin(phi))/(-2)/cos(phi)'
vars = 'f0 f1 sxx syy phi'
vals = 'f0 f1 s_xx s_yy 0.8726646'
[../]
[./should_be_zero_coh]
type = ParsedFunction
value = 'if(abs(a-b)<1E-6,0,1E6*abs(a-b))'
vars = 'a b'
vals = 'Coh_analytic Coh_moose'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./mc_int]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn0]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn1]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn2]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn3]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn4]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn5]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./mc_int_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_internal_parameter
variable = mc_int
[../]
[./yield_fcn0]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn0
[../]
[./yield_fcn1]
type = MaterialStdVectorAux
index = 1
property = plastic_yield_function
variable = yield_fcn1
[../]
[./yield_fcn2]
type = MaterialStdVectorAux
index = 2
property = plastic_yield_function
variable = yield_fcn2
[../]
[./yield_fcn3]
type = MaterialStdVectorAux
index = 3
property = plastic_yield_function
variable = yield_fcn3
[../]
[./yield_fcn4]
type = MaterialStdVectorAux
index = 4
property = plastic_yield_function
variable = yield_fcn4
[../]
[./yield_fcn5]
type = MaterialStdVectorAux
index = 5
property = plastic_yield_function
variable = yield_fcn5
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./internal]
type = PointValue
point = '0 0 0'
variable = mc_int
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = yield_fcn0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = yield_fcn1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = yield_fcn2
[../]
[./f3]
type = PointValue
point = '0 0 0'
variable = yield_fcn3
[../]
[./f4]
type = PointValue
point = '0 0 0'
variable = yield_fcn4
[../]
[./f5]
type = PointValue
point = '0 0 0'
variable = yield_fcn5
[../]
[./yfcns_should_be_zero]
type = FunctionValuePostprocessor
function = should_be_zero_fcn
[../]
[./Coh_analytic]
type = FunctionValuePostprocessor
function = coh_analytic
[../]
[./Coh_moose]
type = FunctionValuePostprocessor
function = coh_from_yieldfcns
[../]
[./cohesion_difference_should_be_zero]
type = FunctionValuePostprocessor
function = should_be_zero_coh
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningExponential
value_0 = 10
value_residual = 20
rate = 1E5
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 0.8726646
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 1 #0.8726646 # 50deg
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulombMulti
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
use_custom_returnMap = true
yield_function_tolerance = 1E-5
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-12
plastic_models = mc
[../]
[]
[Executioner]
end_time = 10
dt = 2
type = Transient
[]
[Outputs]
file_base = planar_hard4
exodus = false
[./csv]
type = CSV
hide = 'f0 f1 f2 f3 f4 f5 s_xy s_xz s_yz Coh_analytic Coh_moose'
execute_on = 'timestep_end'
[../]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/planar_hard3.i)
# apply repeated stretches in x z directions, and smaller stretches along the y direction,
# so that sigma_I = sigma_II,
# which means that lode angle = 30deg.
# Both return to the edge (lode angle = 30deg, ie 010100) and tip are experienced.
#
# It is checked that the yield functions are less than their tolerance values
# It is checked that the cohesion hardens correctly
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '1E-6*x*t'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0.05E-6*y*t'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z*t'
[../]
[]
[Functions]
[./should_be_zero_fcn]
type = ParsedFunction
value = 'if((a<1E-5)&(b<1E-5)&(c<1E-5)&(d<1E-5)&(g<1E-5)&(h<1E-5),0,abs(a)+abs(b)+abs(c)+abs(d)+abs(g)+abs(h))'
vars = 'a b c d g h'
vals = 'f0 f1 f2 f3 f4 f5'
[../]
[./coh_analytic]
type = ParsedFunction
value = '20-10*exp(-1E5*intnl)'
vars = intnl
vals = internal
[../]
[./coh_from_yieldfcns]
type = ParsedFunction
value = '(f0+f1-(sxx+syy)*sin(phi))/(-2)/cos(phi)'
vars = 'f0 f1 sxx syy phi'
vals = 'f0 f1 s_xx s_yy 0.8726646'
[../]
[./should_be_zero_coh]
type = ParsedFunction
value = 'if(abs(a-b)<1E-6,0,1E6*abs(a-b))'
vars = 'a b'
vals = 'Coh_analytic Coh_moose'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./mc_int]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn0]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn1]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn2]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn3]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn4]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn5]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./mc_int_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_internal_parameter
variable = mc_int
[../]
[./yield_fcn0]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn0
[../]
[./yield_fcn1]
type = MaterialStdVectorAux
index = 1
property = plastic_yield_function
variable = yield_fcn1
[../]
[./yield_fcn2]
type = MaterialStdVectorAux
index = 2
property = plastic_yield_function
variable = yield_fcn2
[../]
[./yield_fcn3]
type = MaterialStdVectorAux
index = 3
property = plastic_yield_function
variable = yield_fcn3
[../]
[./yield_fcn4]
type = MaterialStdVectorAux
index = 4
property = plastic_yield_function
variable = yield_fcn4
[../]
[./yield_fcn5]
type = MaterialStdVectorAux
index = 5
property = plastic_yield_function
variable = yield_fcn5
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./internal]
type = PointValue
point = '0 0 0'
variable = mc_int
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = yield_fcn0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = yield_fcn1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = yield_fcn2
[../]
[./f3]
type = PointValue
point = '0 0 0'
variable = yield_fcn3
[../]
[./f4]
type = PointValue
point = '0 0 0'
variable = yield_fcn4
[../]
[./f5]
type = PointValue
point = '0 0 0'
variable = yield_fcn5
[../]
[./yfcns_should_be_zero]
type = FunctionValuePostprocessor
function = should_be_zero_fcn
[../]
[./Coh_analytic]
type = FunctionValuePostprocessor
function = coh_analytic
[../]
[./Coh_moose]
type = FunctionValuePostprocessor
function = coh_from_yieldfcns
[../]
[./cohesion_difference_should_be_zero]
type = FunctionValuePostprocessor
function = should_be_zero_coh
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningExponential
value_0 = 10
value_residual = 20
rate = 1E5
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 0.8726646
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 1 #0.8726646 # 50deg
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulombMulti
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
yield_function_tolerance = 1E-5
use_custom_returnMap = true
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-12
plastic_models = mc
[../]
[]
[Executioner]
end_time = 5
dt = 1
type = Transient
[]
[Outputs]
file_base = planar_hard3
exodus = false
[./csv]
type = CSV
hide = 'f0 f1 f2 f3 f4 f5 s_xy s_xz s_yz Coh_analytic Coh_moose'
execute_on = 'timestep_end'
[../]
[]
(modules/tensor_mechanics/test/tests/multi/three_surface20.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 1.5
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 1.1E-6m in y direction and 1.7E-6 in z direction.
# trial stress_yy = 1.1 and stress_zz = 1.7
#
# Then all yield functions will activate
# However, there is linear dependence. SimpleTester1 will be rutned off.
# The algorithm will return to
# stress_yy=0.5 and stress_zz=1
# internal0=0.1, internal2=0.6
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1.1E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1.7E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 1.5
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface20
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/cp_slip_rate_integ/crysp_substep.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'disp_x disp_y disp_z'
[]
[Variables]
[./disp_x]
block = 0
[../]
[./disp_y]
block = 0
[../]
[./disp_z]
block = 0
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./e_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./gss1]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./e_zz]
type = RankTwoAux
variable = e_zz
rank_two_tensor = lage
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./gss1]
type = MaterialStdVectorAux
variable = gss1
property = gss
index = 0
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = disp_y
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = disp_x
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = disp_z
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_z
boundary = front
function = tdisp
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainCPSlipRateRes
block = 0
gtol = 1e-2
slip_sys_file_name = input_slip_sys.txt
nss = 12
num_slip_sys_flowrate_props = 2 #Number of properties in a slip system
flowprops = '1 4 0.001 0.01 5 8 0.001 0.01 9 12 0.001 0.01'
hprops = '1.0 541.5 60.8 109.8 2.5'
gprops = '1 4 60.8 5 8 60.8 9 12 60.8'
tan_mod_type = exact
slip_incr_tol = 1
maximum_substep_iteration = 8
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
block = 0
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./e_zz]
type = ElementAverageValue
variable = e_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./gss1]
type = ElementAverageValue
variable = gss1
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type'
petsc_options_value = 'lu'
nl_rel_tol = 1e-10
nl_abs_tol = 1e-10
dt = 0.2
dtmax = 10.0
dtmin = 0.05
end_time = 1
[]
[Outputs]
file_base = crysp_substep_out
exodus = true
print_linear_residuals = true
perf_graph = true
[]
(modules/tensor_mechanics/test/tests/multi/three_surface00.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 1.5
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 1E-6m in y direction and 1E-6 in z direction.
# trial stress_yy = 1 and stress_zz = 1
#
# Then SimpleTester2 should activate and the algorithm will return to
# stress_yy = 0.75, stress_zz = 0.75
# internal2 should be 0.25
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 1.5
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1 1'
debug_jac_at_intnl = '1 1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface00
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/elem_prop_read_user_object/prop_grain_read.i)
[Mesh]
type = GeneratedMesh
dim = 2
elem_type = QUAD4
displacements = 'disp_x disp_y'
nx = 10
ny = 10
[]
[Variables]
[./disp_x]
block = 0
[../]
[./disp_y]
block = 0
[../]
[]
[GlobalParams]
volumetric_locking_correction=true
[]
[AuxVariables]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./e_yy]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.05*t
[../]
[]
[UserObjects]
[./prop_read]
type = PropertyReadFile
prop_file_name = 'input_file.txt'
# Enter file data as prop#1, prop#2, .., prop#nprop
nprop = 4
read_type = voronoi
nvoronoi = 3
use_random_voronoi = true
rand_seed = 25346
rve_type = periodic
[../]
[]
[AuxKernels]
[./stress_yy]
type = RankTwoAux
variable = stress_yy
rank_two_tensor = stress
index_j = 1
index_i = 1
execute_on = timestep_end
block = 0
[../]
[./e_yy]
type = RankTwoAux
variable = e_yy
rank_two_tensor = elastic_strain
index_j = 1
index_i = 1
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./fix_x]
type = DirichletBC
variable = disp_x
boundary = 'left'
value = 0
[../]
[./fix_y]
type = DirichletBC
variable = disp_y
boundary = 'bottom'
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_y
boundary = top
function = tdisp
[../]
[]
[Materials]
[./elasticity_tensor_with_Euler]
type = ComputeElasticityTensorCP
block = 0
C_ijkl = '1.684e5 0.176e5 0.176e5 1.684e5 0.176e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
read_prop_user_object = prop_read
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y'
[../]
[./stress]
type = ComputeFiniteStrainElasticStress
block = 0
[../]
[]
[Postprocessors]
[./stress_yy]
type = ElementAverageValue
variable = stress_yy
block = 'ANY_BLOCK_ID 0'
[../]
[./e_yy]
type = ElementAverageValue
variable = e_yy
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.05
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
nl_abs_tol = 1e-10
nl_rel_step_tol = 1e-10
dtmax = 10.0
nl_rel_tol = 1e-10
end_time = 1
dtmin = 0.05
num_steps = 1
nl_abs_step_tol = 1e-10
[]
[Outputs]
file_base = prop_grain_read_out
exodus = true
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y'
use_displaced_mesh = true
[../]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/planar_hard5.i)
# apply repeated stretches in z direction, and smaller stretches along the y direction, and compression along x direction
# Both return to the plane and edge (lode angle = 30deg, ie 010100) are experienced.
#
# It is checked that the yield functions are less than their tolerance values
# It is checked that the cohesion hardens correctly
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '-1E-6*x*t'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0.05E-6*y*t'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z*t'
[../]
[]
[Functions]
[./should_be_zero_fcn]
type = ParsedFunction
value = 'if((a<1E-5)&(b<1E-5)&(c<1E-5)&(d<1E-5)&(g<1E-5)&(h<1E-5),0,abs(a)+abs(b)+abs(c)+abs(d)+abs(g)+abs(h))'
vars = 'a b c d g h'
vals = 'f0 f1 f2 f3 f4 f5'
[../]
[./coh_analytic]
type = ParsedFunction
value = '20-10*exp(-1E6*intnl)'
vars = intnl
vals = internal
[../]
[./coh_from_yieldfcns]
type = ParsedFunction
value = '(f0+f1-(sxx+syy)*sin(phi))/(-2)/cos(phi)'
vars = 'f0 f1 sxx syy phi'
vals = 'f0 f1 s_xx s_yy 0.8726646'
[../]
[./should_be_zero_coh]
type = ParsedFunction
value = 'if(abs(a-b)<1E-6,0,1E6*abs(a-b))'
vars = 'a b'
vals = 'Coh_analytic Coh_moose'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./mc_int]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn0]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn1]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn2]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn3]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn4]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn5]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./mc_int_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_internal_parameter
variable = mc_int
[../]
[./yield_fcn0]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn0
[../]
[./yield_fcn1]
type = MaterialStdVectorAux
index = 1
property = plastic_yield_function
variable = yield_fcn1
[../]
[./yield_fcn2]
type = MaterialStdVectorAux
index = 2
property = plastic_yield_function
variable = yield_fcn2
[../]
[./yield_fcn3]
type = MaterialStdVectorAux
index = 3
property = plastic_yield_function
variable = yield_fcn3
[../]
[./yield_fcn4]
type = MaterialStdVectorAux
index = 4
property = plastic_yield_function
variable = yield_fcn4
[../]
[./yield_fcn5]
type = MaterialStdVectorAux
index = 5
property = plastic_yield_function
variable = yield_fcn5
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./internal]
type = PointValue
point = '0 0 0'
variable = mc_int
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = yield_fcn0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = yield_fcn1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = yield_fcn2
[../]
[./f3]
type = PointValue
point = '0 0 0'
variable = yield_fcn3
[../]
[./f4]
type = PointValue
point = '0 0 0'
variable = yield_fcn4
[../]
[./f5]
type = PointValue
point = '0 0 0'
variable = yield_fcn5
[../]
[./yfcns_should_be_zero]
type = FunctionValuePostprocessor
function = should_be_zero_fcn
[../]
[./Coh_analytic]
type = FunctionValuePostprocessor
function = coh_analytic
[../]
[./Coh_moose]
type = FunctionValuePostprocessor
function = coh_from_yieldfcns
[../]
[./cohesion_difference_should_be_zero]
type = FunctionValuePostprocessor
function = should_be_zero_coh
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningExponential
value_0 = 10
value_residual = 20
rate = 1E6
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 0.8726646
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 1 #0.8726646 # 50deg
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulombMulti
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
use_custom_returnMap = true
yield_function_tolerance = 1E-5
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-12
plastic_models = mc
[../]
[]
[Executioner]
end_time = 5
dt = 1
type = Transient
[]
[Outputs]
file_base = planar_hard5
exodus = false
[./csv]
type = CSV
hide = 'f0 f1 f2 f3 f4 f5 s_xy s_xz s_yz Coh_analytic Coh_moose'
execute_on = 'timestep_end'
[../]
[]
(modules/tensor_mechanics/examples/bridge/bridge_large_strain.i)
#
# Bridge linear elasticity example
#
# This example models a bridge using linear elasticity.
# It can be either steel or concrete.
# Gravity is applied
# A pressure of 0.5 MPa is also applied
#
[Mesh]
displacements = 'disp_x disp_y disp_z' #Define displacements for deformed mesh
type = FileMesh #Read in mesh from file
file = bridge.e
boundary_id = '1 2 3 4 5 6' #Assign names to boundaries to make things clearer
boundary_name = 'top left right bottom1 bottom2 bottom3'
[]
[Variables]
[./disp_x]
order = FIRST
family = LAGRANGE
[../]
[./disp_y]
order = FIRST
family = LAGRANGE
[../]
[./disp_z]
order = FIRST
family = LAGRANGE
[../]
[]
[Kernels]
[./gravity_y]
#Gravity is applied to bridge
type = Gravity
variable = disp_y
value = -9.81
[../]
[./TensorMechanics]
#Stress divergence kernels
displacements = 'disp_x disp_y disp_z'
[../]
[]
[AuxVariables]
[./von_mises]
#Dependent variable used to visualize the Von Mises stress
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./von_mises_kernel]
#Calculates the von mises stress and assigns it to von_mises
type = RankTwoScalarAux
variable = von_mises
rank_two_tensor = stress
execute_on = timestep_end
scalar_type = VonMisesStress
[../]
[]
[BCs]
[./Pressure]
[./load]
#Applies the pressure
boundary = top
factor = 5e5 # Pa
[../]
[../]
[./anchor_x]
#Anchors the bottom and sides against deformation in the x-direction
type = DirichletBC
variable = disp_x
boundary = 'left right bottom1 bottom2 bottom3'
value = 0.0
[../]
[./anchor_y]
#Anchors the bottom and sides against deformation in the y-direction
type = DirichletBC
variable = disp_y
boundary = 'left right bottom1 bottom2 bottom3'
value = 0.0
[../]
[./anchor_z]
#Anchors the bottom and sides against deformation in the z-direction
type = DirichletBC
variable = disp_z
boundary = 'left right bottom1 bottom2 bottom3'
value = 0.0
[../]
[]
[Materials]
active = 'density_steel stress strain elasticity_tensor_steel'
[./elasticity_tensor_steel]
#Creates the elasticity tensor using steel parameters
youngs_modulus = 210e9 #Pa
poissons_ratio = 0.3
type = ComputeIsotropicElasticityTensor
block = 1
[../]
[./elasticity_tensor_concrete]
#Creates the elasticity tensor using concrete parameters
youngs_modulus = 16.5e9 #Pa
poissons_ratio = 0.2
type = ComputeIsotropicElasticityTensor
block = 1
[../]
[./strain]
#Computes the strain, assuming small strains
type = ComputeFiniteStrain
block = 1
displacements = 'disp_x disp_y disp_z'
[../]
[./stress]
#Computes the stress, using linear elasticity
type = ComputeFiniteStrainElasticStress
block = 1
[../]
[./density_steel]
#Defines the density of steel
type = GenericConstantMaterial
block = 1
prop_names = density
prop_values = 7850 # kg/m^3
[../]
[./density_concrete]
#Defines the density of concrete
type = GenericConstantMaterial
block = 1
prop_names = density
prop_values = 2400 # kg/m^3
[../]
[]
[Preconditioning]
[./SMP]
#Creates the entire Jacobian, for the Newton solve
type = SMP
full = true
[../]
[]
[Executioner]
#We solve a steady state problem using Newton's iteration
type = Transient
solve_type = NEWTON
nl_rel_tol = 1e-9
l_max_its = 30
l_tol = 1e-4
nl_max_its = 10
petsc_options_iname = '-pc_type -pc_hypre_type -ksp_gmres_restart'
petsc_options_value = 'hypre boomeramg 31'
dt = 0.1
num_steps = 1
[]
[Outputs]
exodus = true
perf_graph = true
[]
(modules/combined/test/tests/poro_mechanics/borehole_highres.i)
# Poroelastic response of a borehole.
#
# HIGHRES VERSION: this version gives good agreement with the analytical solution, but it takes a while so is a "heavy" test
#
# A fully-saturated medium contains a fluid with a homogeneous porepressure,
# but an anisitropic insitu stress. A infinitely-long borehole aligned with
# the $$z$$ axis is instanteously excavated. The borehole boundary is
# stress-free and allowed to freely drain. This problem is analysed using
# plane-strain conditions (no $$z$$ displacement).
#
# The solution in Laplace space is found in E Detournay and AHD Cheng "Poroelastic response of a borehole in a non-hydrostatic stress field". International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts 25 (1988) 171-182. In the small-time limit, the Laplace transforms may be performed. There is one typo in the paper. Equation (A4)'s final term should be -(a/r)\sqrt(4ct/(a^2\pi)), and not +(a/r)\sqrt(4ct/(a^2\pi)).
#
# Because realistic parameters are chosen (below),
# the residual for porepressure is much smaller than
# the residuals for the displacements. Therefore the
# scaling parameter is chosen. Also note that the
# insitu stresses are effective stresses, not total
# stresses, but the solution in the above paper is
# expressed in terms of total stresses.
#
# Here are the problem's parameters, and their values:
# Borehole radius. a = 1
# Rock's Lame lambda. la = 0.5E9
# Rock's Lame mu, which is also the Rock's shear modulus. mu = G = 1.5E9
# Rock bulk modulus. K = la + 2*mu/3 = 1.5E9
# Drained Poisson ratio. nu = (3K - 2G)/(6K + 2G) = 0.125
# Rock bulk compliance. 1/K = 0.66666666E-9
# Fluid bulk modulus. Kf = 0.7171315E9
# Fluid bulk compliance. 1/Kf = 1.39444444E-9
# Rock initial porosity. phi0 = 0.3
# Biot coefficient. alpha = 0.65
# Biot modulus. M = 1/(phi0/Kf + (alpha - phi0)(1 - alpha)/K) = 2E9
# Undrained bulk modulus. Ku = K + alpha^2*M = 2.345E9
# Undrained Poisson ratio. nuu = (3Ku - 2G)/(6Ku + 2G) = 0.2364
# Skempton coefficient. B = alpha*M/Ku = 0.554
# Fluid mobility (rock permeability/fluid viscosity). k = 1E-12
[Mesh]
type = FileMesh
file = borehole_highres_input.e
[]
[GlobalParams]
displacements = 'disp_x disp_y disp_z'
porepressure = porepressure
block = 1
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[./porepressure]
scaling = 1E9 # Notice the scaling, to make porepressure's kernels roughly of same magnitude as disp's kernels
[../]
[]
[GlobalParams]
volumetric_locking_correction=true
[]
[ICs]
[./initial_p]
type = ConstantIC
variable = porepressure
value = 1E6
[../]
[]
[BCs]
[./fixed_outer_x]
type = DirichletBC
variable = disp_x
value = 0
boundary = outer
[../]
[./fixed_outer_y]
type = DirichletBC
variable = disp_y
value = 0
boundary = outer
[../]
[./plane_strain]
type = DirichletBC
variable = disp_z
value = 0
boundary = 'zmin zmax'
[../]
[./borehole_wall]
type = DirichletBC
variable = porepressure
value = 0
boundary = bh_wall
[../]
[]
[AuxVariables]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./tot_yy]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./tot_yy]
type = ParsedAux
args = 'stress_yy porepressure'
execute_on = timestep_end
variable = tot_yy
function = 'stress_yy-0.65*porepressure'
[../]
[]
[Kernels]
[./grad_stress_x]
type = StressDivergenceTensors
variable = disp_x
component = 0
[../]
[./grad_stress_y]
type = StressDivergenceTensors
variable = disp_y
component = 1
[../]
[./grad_stress_z]
type = StressDivergenceTensors
variable = disp_z
component = 2
[../]
[./poro_x]
type = PoroMechanicsCoupling
variable = disp_x
component = 0
[../]
[./poro_y]
type = PoroMechanicsCoupling
variable = disp_y
component = 1
[../]
[./poro_z]
type = PoroMechanicsCoupling
variable = disp_z
component = 2
[../]
[./poro_timederiv]
type = PoroFullSatTimeDerivative
variable = porepressure
[../]
[./darcy_flow]
type = CoefDiffusion
variable = porepressure
coef = 1E-12
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
C_ijkl = '0.5E9 1.5E9'
# bulk modulus is lambda + 2*mu/3 = 0.5 + 2*1.5/3 = 1.5E9
fill_method = symmetric_isotropic
[../]
[./strain]
type = ComputeFiniteStrain
displacements = 'disp_x disp_y disp_z'
eigenstrain_names = ini_stress
[../]
[./ini_stress]
type = ComputeEigenstrainFromInitialStress
initial_stress = '-1.35E6 0 0 0 -3.35E6 0 0 0 0' # remember this is the effective stress
eigenstrain_name = ini_stress
[../]
[./no_plasticity]
type = ComputeFiniteStrainElasticStress
[../]
[./poro_material]
type = PoroFullSatMaterial
porosity0 = 0.3
biot_coefficient = 0.65
solid_bulk_compliance = 0.6666666666667E-9
fluid_bulk_compliance = 1.3944444444444E-9
constant_porosity = false
[../]
[]
[Postprocessors]
[./p00]
type = PointValue
variable = porepressure
point = '1.00 0 0'
outputs = csv_p
[../]
[./p01]
type = PointValue
variable = porepressure
point = '1.01 0 0'
outputs = csv_p
[../]
[./p02]
type = PointValue
variable = porepressure
point = '1.02 0 0'
outputs = csv_p
[../]
[./p03]
type = PointValue
variable = porepressure
point = '1.03 0 0'
outputs = csv_p
[../]
[./p04]
type = PointValue
variable = porepressure
point = '1.04 0 0'
outputs = csv_p
[../]
[./p05]
type = PointValue
variable = porepressure
point = '1.05 0 0'
outputs = csv_p
[../]
[./p06]
type = PointValue
variable = porepressure
point = '1.06 0 0'
outputs = csv_p
[../]
[./p07]
type = PointValue
variable = porepressure
point = '1.07 0 0'
outputs = csv_p
[../]
[./p08]
type = PointValue
variable = porepressure
point = '1.08 0 0'
outputs = csv_p
[../]
[./p09]
type = PointValue
variable = porepressure
point = '1.09 0 0'
outputs = csv_p
[../]
[./p10]
type = PointValue
variable = porepressure
point = '1.10 0 0'
outputs = csv_p
[../]
[./p11]
type = PointValue
variable = porepressure
point = '1.11 0 0'
outputs = csv_p
[../]
[./p12]
type = PointValue
variable = porepressure
point = '1.12 0 0'
outputs = csv_p
[../]
[./p13]
type = PointValue
variable = porepressure
point = '1.13 0 0'
outputs = csv_p
[../]
[./p14]
type = PointValue
variable = porepressure
point = '1.14 0 0'
outputs = csv_p
[../]
[./p15]
type = PointValue
variable = porepressure
point = '1.15 0 0'
outputs = csv_p
[../]
[./p16]
type = PointValue
variable = porepressure
point = '1.16 0 0'
outputs = csv_p
[../]
[./p17]
type = PointValue
variable = porepressure
point = '1.17 0 0'
outputs = csv_p
[../]
[./p18]
type = PointValue
variable = porepressure
point = '1.18 0 0'
outputs = csv_p
[../]
[./p19]
type = PointValue
variable = porepressure
point = '1.19 0 0'
outputs = csv_p
[../]
[./p20]
type = PointValue
variable = porepressure
point = '1.20 0 0'
outputs = csv_p
[../]
[./p21]
type = PointValue
variable = porepressure
point = '1.21 0 0'
outputs = csv_p
[../]
[./p22]
type = PointValue
variable = porepressure
point = '1.22 0 0'
outputs = csv_p
[../]
[./p23]
type = PointValue
variable = porepressure
point = '1.23 0 0'
outputs = csv_p
[../]
[./p24]
type = PointValue
variable = porepressure
point = '1.24 0 0'
outputs = csv_p
[../]
[./p25]
type = PointValue
variable = porepressure
point = '1.25 0 0'
outputs = csv_p
[../]
[./s00]
type = PointValue
variable = disp_x
point = '1.00 0 0'
outputs = csv_s
[../]
[./s01]
type = PointValue
variable = disp_x
point = '1.01 0 0'
outputs = csv_s
[../]
[./s02]
type = PointValue
variable = disp_x
point = '1.02 0 0'
outputs = csv_s
[../]
[./s03]
type = PointValue
variable = disp_x
point = '1.03 0 0'
outputs = csv_s
[../]
[./s04]
type = PointValue
variable = disp_x
point = '1.04 0 0'
outputs = csv_s
[../]
[./s05]
type = PointValue
variable = disp_x
point = '1.05 0 0'
outputs = csv_s
[../]
[./s06]
type = PointValue
variable = disp_x
point = '1.06 0 0'
outputs = csv_s
[../]
[./s07]
type = PointValue
variable = disp_x
point = '1.07 0 0'
outputs = csv_s
[../]
[./s08]
type = PointValue
variable = disp_x
point = '1.08 0 0'
outputs = csv_s
[../]
[./s09]
type = PointValue
variable = disp_x
point = '1.09 0 0'
outputs = csv_s
[../]
[./s10]
type = PointValue
variable = disp_x
point = '1.10 0 0'
outputs = csv_s
[../]
[./s11]
type = PointValue
variable = disp_x
point = '1.11 0 0'
outputs = csv_s
[../]
[./s12]
type = PointValue
variable = disp_x
point = '1.12 0 0'
outputs = csv_s
[../]
[./s13]
type = PointValue
variable = disp_x
point = '1.13 0 0'
outputs = csv_s
[../]
[./s14]
type = PointValue
variable = disp_x
point = '1.14 0 0'
outputs = csv_s
[../]
[./s15]
type = PointValue
variable = disp_x
point = '1.15 0 0'
outputs = csv_s
[../]
[./s16]
type = PointValue
variable = disp_x
point = '1.16 0 0'
outputs = csv_s
[../]
[./s17]
type = PointValue
variable = disp_x
point = '1.17 0 0'
outputs = csv_s
[../]
[./s18]
type = PointValue
variable = disp_x
point = '1.18 0 0'
outputs = csv_s
[../]
[./s19]
type = PointValue
variable = disp_x
point = '1.19 0 0'
outputs = csv_s
[../]
[./s20]
type = PointValue
variable = disp_x
point = '1.20 0 0'
outputs = csv_s
[../]
[./s21]
type = PointValue
variable = disp_x
point = '1.21 0 0'
outputs = csv_s
[../]
[./s22]
type = PointValue
variable = disp_x
point = '1.22 0 0'
outputs = csv_s
[../]
[./s23]
type = PointValue
variable = disp_x
point = '1.23 0 0'
outputs = csv_s
[../]
[./s24]
type = PointValue
variable = disp_x
point = '1.24 0 0'
outputs = csv_s
[../]
[./s25]
type = PointValue
variable = disp_x
point = '1.25 0 0'
outputs = csv_s
[../]
[./t00]
type = PointValue
variable = tot_yy
point = '1.00 0 0'
outputs = csv_t
[../]
[./t01]
type = PointValue
variable = tot_yy
point = '1.01 0 0'
outputs = csv_t
[../]
[./t02]
type = PointValue
variable = tot_yy
point = '1.02 0 0'
outputs = csv_t
[../]
[./t03]
type = PointValue
variable = tot_yy
point = '1.03 0 0'
outputs = csv_t
[../]
[./t04]
type = PointValue
variable = tot_yy
point = '1.04 0 0'
outputs = csv_t
[../]
[./t05]
type = PointValue
variable = tot_yy
point = '1.05 0 0'
outputs = csv_t
[../]
[./t06]
type = PointValue
variable = tot_yy
point = '1.06 0 0'
outputs = csv_t
[../]
[./t07]
type = PointValue
variable = tot_yy
point = '1.07 0 0'
outputs = csv_t
[../]
[./t08]
type = PointValue
variable = tot_yy
point = '1.08 0 0'
outputs = csv_t
[../]
[./t09]
type = PointValue
variable = tot_yy
point = '1.09 0 0'
outputs = csv_t
[../]
[./t10]
type = PointValue
variable = tot_yy
point = '1.10 0 0'
outputs = csv_t
[../]
[./t11]
type = PointValue
variable = tot_yy
point = '1.11 0 0'
outputs = csv_t
[../]
[./t12]
type = PointValue
variable = tot_yy
point = '1.12 0 0'
outputs = csv_t
[../]
[./t13]
type = PointValue
variable = tot_yy
point = '1.13 0 0'
outputs = csv_t
[../]
[./t14]
type = PointValue
variable = tot_yy
point = '1.14 0 0'
outputs = csv_t
[../]
[./t15]
type = PointValue
variable = tot_yy
point = '1.15 0 0'
outputs = csv_t
[../]
[./t16]
type = PointValue
variable = tot_yy
point = '1.16 0 0'
outputs = csv_t
[../]
[./t17]
type = PointValue
variable = tot_yy
point = '1.17 0 0'
outputs = csv_t
[../]
[./t18]
type = PointValue
variable = tot_yy
point = '1.18 0 0'
outputs = csv_t
[../]
[./t19]
type = PointValue
variable = tot_yy
point = '1.19 0 0'
outputs = csv_t
[../]
[./t20]
type = PointValue
variable = tot_yy
point = '1.20 0 0'
outputs = csv_t
[../]
[./t21]
type = PointValue
variable = tot_yy
point = '1.21 0 0'
outputs = csv_t
[../]
[./t22]
type = PointValue
variable = tot_yy
point = '1.22 0 0'
outputs = csv_t
[../]
[./t23]
type = PointValue
variable = tot_yy
point = '1.23 0 0'
outputs = csv_t
[../]
[./t24]
type = PointValue
variable = tot_yy
point = '1.24 0 0'
outputs = csv_t
[../]
[./t25]
type = PointValue
variable = tot_yy
point = '1.25 0 0'
outputs = csv_t
[../]
[./dt]
type = FunctionValuePostprocessor
outputs = console
function = 2*t
[../]
[]
[Preconditioning]
[./andy]
type = SMP
full = true
petsc_options = '-snes_monitor -snes_linesearch_monitor'
petsc_options_iname = '-ksp_type -pc_type -snes_atol -snes_rtol -snes_max_it -ksp_max_it -sub_pc_type -sub_pc_factor_shift_type'
petsc_options_value = 'gmres asm 1E0 1E-10 200 500 lu NONZERO'
[../]
[]
[Executioner]
type = Transient
solve_type = Newton
start_time = 0
end_time = 0.3
dt = 0.1
#[./TimeStepper]
# type = PostprocessorDT
# postprocessor = dt
# dt = 0.003
#[../]
[]
[Outputs]
execute_on = 'timestep_end'
file_base = borehole_highres
exodus = true
sync_times = '0.003 0.3'
[./csv_p]
file_base = borehole_highres_p
type = CSV
[../]
[./csv_s]
file_base = borehole_highres_s
type = CSV
[../]
[./csv_t]
file_base = borehole_highres_t
type = CSV
[../]
[]
(modules/contact/test/tests/verification/patch_tests/brick_4/brick4_mu_0_2_pen.i)
[GlobalParams]
order = SECOND
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
file = brick4_mesh.e
[]
[Problem]
type = ReferenceResidualProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./penetration]
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./saved_z]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./diag_saved_z]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./inc_slip_z]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./accum_slip_z]
[../]
[./tang_force_x]
[../]
[./tang_force_y]
[../]
[./tang_force_z]
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y saved_z'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_end
boundary = 3
paired_boundary = 4
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_end
boundary = 3
paired_boundary = 4
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 3
paired_boundary = 4
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 3
paired_boundary = 4
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 3
paired_boundary = 4
[../]
[./tang_force_x]
type = PenetrationAux
variable = tang_force_x
quantity = tangential_force_x
boundary = 3
paired_boundary = 4
[../]
[./tang_force_y]
type = PenetrationAux
variable = tang_force_y
quantity = tangential_force_y
boundary = 3
paired_boundary = 4
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./ref_resid_x]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_x
[../]
[./ref_resid_y]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_y
[../]
[./sigma_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./sigma_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./disp_x59]
type = NodalVariableValue
nodeid = 58
variable = disp_x
[../]
[./disp_x64]
type = NodalVariableValue
nodeid = 63
variable = disp_x
[../]
[./disp_y59]
type = NodalVariableValue
nodeid = 58
variable = disp_y
[../]
[./disp_y64]
type = NodalVariableValue
nodeid = 63
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./bot_y]
type = DirichletBC
variable = disp_y
boundary = 1
value = 0.0
[../]
[./side_x]
type = DirichletBC
variable = disp_x
boundary = 2
value = 0.0
[../]
[./back_z]
type = DirichletBC
variable = disp_z
boundary = 6
value = 0.0
[../]
[./top_press]
type = Pressure
variable = disp_y
boundary = 5
factor = 109.89
[../]
[]
[Materials]
[./bot_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./bot_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./bot_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./top_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./top_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./top_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-7
nl_rel_tol = 1e-6
l_max_its = 50
nl_max_its = 100
dt = 1.0
end_time = 1.0
num_steps = 10
dtmin = 1.0
l_tol = 1e-4
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '1 3 4 5'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '1 3 4 5'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
file_base = brick4_mu_0_2_pen_out
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
file_base = brick4_mu_0_2_pen_check
show = 'bot_react_x bot_react_y disp_x59 disp_y59 disp_x64 disp_y64 stress_yy stress_zz top_react_x top_react_y x_disp y_disp cont_press'
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./leftright]
secondary = 3
primary = 4
model = coulomb
formulation = penalty
normalize_penalty = true
friction_coefficient = 0.2
penalty = 1e+6
[../]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform5.i)
# apply repeated stretches in x z directions, and smaller stretches along the y direction,
# so that sigma_I = sigma_II,
# which means that lode angle = 30deg.
# The allows yield surface in meridional plane to be mapped out
# Use 'cap' smoothing
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '1E-6*x*t'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0.9E-6*y*sin(t)'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z*t'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./mc_int]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./mc_int_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_internal_parameter
variable = mc_int
[../]
[./yield_fcn_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn
[../]
[./iter_auxk]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./internal]
type = PointValue
point = '0 0 0'
variable = mc_int
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = yield_fcn
[../]
[./iter]
type = PointValue
point = '0 0 0'
variable = iter
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 10
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 50
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningExponential
value_0 = 0
value_residual = 0.8726646 # 50deg
rate = 3000.0
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
tip_scheme = cap
mc_tip_smoother = 0
cap_start = 3
cap_rate = 0.8
mc_edge_smoother = 20
yield_function_tolerance = 1E-8
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = mc
debug_fspb = crash
[../]
[]
[Executioner]
end_time = 150
dt = 5
type = Transient
[]
[Outputs]
file_base = small_deform5
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/multi/three_surface05.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 1.5
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 1E-6m in y direction and 1.1E-6 in z direction.
# trial stress_yy = 1 and stress_zz = 1.1
#
# Then SimpleTester0 and SimpleTester2 should activate and the algorithm will return to
# the corner stress_yy=0.5, stress_zz=1
# However, this will mean internal0 < 0, so SimpleTester0 will be deactivated and
# then the algorithm will return to
# stress_yy=0.7, stress_zz=0.8
# internal0 should be 0.0, and internal2 should be 0.3
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1.0E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1.1E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 1.5
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface05
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/exception.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'ux uy uz'
[]
[Variables]
[./ux]
[../]
[./uy]
[../]
[./uz]
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./pk2]
order = CONSTANT
family = MONOMIAL
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./rotout]
order = CONSTANT
family = MONOMIAL
[../]
[./e_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./gss]
order = CONSTANT
family = MONOMIAL
[../]
[./slip_increment]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.1*t
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'ux uy uz'
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./pk2]
type = RankTwoAux
variable = pk2
rank_two_tensor = pk2
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./e_zz]
type = RankTwoAux
variable = e_zz
rank_two_tensor = lage
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./gss]
type = MaterialStdVectorAux
variable = gss
property = state_var_gss
index = 0
execute_on = timestep_end
[../]
[./slip_inc]
type = MaterialStdVectorAux
variable = slip_increment
property = slip_rate_gss
index = 0
execute_on = timestep_end
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = uy
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = ux
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = uz
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = uz
boundary = front
function = tdisp
[../]
[]
[UserObjects]
[./slip_rate_gss]
type = CrystalPlasticitySlipRateGSS
variable_size = 12
slip_sys_file_name = input_slip_sys.txt
num_slip_sys_flowrate_props = 2
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
uo_state_var_name = state_var_gss
[../]
[./slip_resistance_gss]
type = CrystalPlasticitySlipResistanceGSS
variable_size = 12
uo_state_var_name = state_var_gss
[../]
[./state_var_gss]
type = CrystalPlasticityStateVariable
variable_size = 12
groups = '0 4 8 12'
group_values = '60.8 60.8 60.8'
uo_state_var_evol_rate_comp_name = state_var_evol_rate_comp_gss
scale_factor = 1.0
[../]
[./state_var_evol_rate_comp_gss]
type = CrystalPlasticityStateVarRateComponentGSS
variable_size = 12
hprops = '1.0 541.5 109.8 2.5'
uo_slip_rate_name = slip_rate_gss
uo_state_var_name = state_var_gss
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainUObasedCP
block = 0
stol = 1e-2
tan_mod_type = exact
uo_slip_rates = 'slip_rate_gss'
uo_slip_resistances = 'slip_resistance_gss'
uo_state_vars = 'state_var_gss'
uo_state_var_evol_rate_comps = 'state_var_evol_rate_comp_gss'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'ux uy uz'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
block = 0
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./pk2]
type = ElementAverageValue
variable = pk2
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
[../]
[./e_zz]
type = ElementAverageValue
variable = e_zz
[../]
[./gss]
type = ElementAverageValue
variable = gss
[../]
[./slip_increment]
type = ElementAverageValue
variable = slip_increment
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.05
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
nl_abs_tol = 1e-10
nl_rel_step_tol = 1e-10
dtmax = 10.0
nl_rel_tol = 1e-10
end_time = 1
dtmin = 0.01
num_steps = 10
nl_abs_step_tol = 1e-10
[]
[Outputs]
exodus = true
[]
(modules/tensor_mechanics/test/tests/multi/three_surface15.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 3
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 3.0E-6m in y direction and 3E-6 in z direction.
# trial stress_yy = 3.0 and stress_zz = 3
#
# A complicated return will follow, with various contraints being
# deactivated, kuhn-tucker failing, line-searching, etc, but
# the result should be
# stress_yy=1=stress_zz, and internal0=2 internal1=2
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '3.0E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '3.0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 3
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 4
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1 1'
debug_jac_at_intnl = '1 1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface15
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/multi/two_surface05.i)
# Plasticit models:
# SimpleTester with a = 0 and b = 1 and strength = 1
# SimpleTester with a = 1 and b = 1 and strength = 2
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 3E-6m in y directions and 1.0E-6 in z direction.
# trial stress_zz = 1 and stress_yy = 3
#
# Then SimpleTester2 should activate and the algorithm will return to
# stress_zz = 0, stress_yy = 2
# internal0 should be zero, and internal1 should be 1
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '3E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[]
[UserObjects]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 2
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = two_surface05
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/visco/visco_finite_strain.i)
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
elem_type = HEX8
displacements = 'disp_x disp_y disp_z'
[]
[Variables]
[./disp_x]
order = FIRST
family = LAGRANGE
[../]
[./disp_y]
order = FIRST
family = LAGRANGE
[../]
[./disp_z]
order = FIRST
family = LAGRANGE
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./strain_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./creep_strain_xx]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
variable = stress_xx
rank_two_tensor = stress
index_j = 0
index_i = 0
execute_on = timestep_end
[../]
[./strain_xx]
type = RankTwoAux
variable = strain_xx
rank_two_tensor = total_strain
index_j = 0
index_i = 0
execute_on = timestep_end
[../]
[./creep_strain_xx]
type = RankTwoAux
variable = creep_strain_xx
rank_two_tensor = creep_strain
index_j = 0
index_i = 0
execute_on = timestep_end
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = disp_y
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = disp_x
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = disp_z
boundary = back
value = 0
[../]
[./axial_load]
type = NeumannBC
variable = disp_x
boundary = right
value = 10e6
[../]
[]
[Materials]
[./kelvin_voigt]
type = GeneralizedKelvinVoigtModel
creep_modulus = '10e9 10e9'
creep_viscosity = '1 10'
poisson_ratio = 0.2
young_modulus = 10e9
[../]
[./stress]
type = ComputeMultipleInelasticStress
inelastic_models = 'creep'
[../]
[./creep]
type = LinearViscoelasticStressUpdate
[../]
[./strain]
type = ComputeFiniteStrain
displacements = 'disp_x disp_y disp_z'
[../]
[]
[UserObjects]
[./update]
type = LinearViscoelasticityManager
viscoelastic_model = kelvin_voigt
[../]
[]
[Postprocessors]
[./stress_xx]
type = ElementAverageValue
variable = stress_xx
block = 'ANY_BLOCK_ID 0'
[../]
[./strain_xx]
type = ElementAverageValue
variable = strain_xx
block = 'ANY_BLOCK_ID 0'
[../]
[./creep_strain_xx]
type = ElementAverageValue
variable = creep_strain_xx
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
l_max_its = 100
l_tol = 1e-8
nl_max_its = 50
nl_rel_tol = 1e-8
nl_abs_tol = 1e-8
dtmin = 0.01
end_time = 100
[./TimeStepper]
type = LogConstantDT
first_dt = 0.1
log_dt = 0.1
[../]
[]
[Outputs]
file_base = visco_finite_strain_out
exodus = true
[]
(modules/combined/test/tests/poro_mechanics/borehole_lowres.i)
# Poroelastic response of a borehole.
#
# LOWRES VERSION: this version does not give perfect agreement with the analytical solution
#
# A fully-saturated medium contains a fluid with a homogeneous porepressure,
# but an anisitropic insitu stress. A infinitely-long borehole aligned with
# the $$z$$ axis is instanteously excavated. The borehole boundary is
# stress-free and allowed to freely drain. This problem is analysed using
# plane-strain conditions (no $$z$$ displacement).
#
# The solution in Laplace space is found in E Detournay and AHD Cheng "Poroelastic response of a borehole in a non-hydrostatic stress field". International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts 25 (1988) 171-182. In the small-time limit, the Laplace transforms may be performed. There is one typo in the paper. Equation (A4)'s final term should be -(a/r)\sqrt(4ct/(a^2\pi)), and not +(a/r)\sqrt(4ct/(a^2\pi)).
#
# Because realistic parameters are chosen (below),
# the residual for porepressure is much smaller than
# the residuals for the displacements. Therefore the
# scaling parameter is chosen. Also note that the
# insitu stresses are effective stresses, not total
# stresses, but the solution in the above paper is
# expressed in terms of total stresses.
#
# Here are the problem's parameters, and their values:
# Borehole radius. a = 1
# Rock's Lame lambda. la = 0.5E9
# Rock's Lame mu, which is also the Rock's shear modulus. mu = G = 1.5E9
# Rock bulk modulus. K = la + 2*mu/3 = 1.5E9
# Drained Poisson ratio. nu = (3K - 2G)/(6K + 2G) = 0.125
# Rock bulk compliance. 1/K = 0.66666666E-9
# Fluid bulk modulus. Kf = 0.7171315E9
# Fluid bulk compliance. 1/Kf = 1.39444444E-9
# Rock initial porosity. phi0 = 0.3
# Biot coefficient. alpha = 0.65
# Biot modulus. M = 1/(phi0/Kf + (alpha - phi0)(1 - alpha)/K) = 2E9
# Undrained bulk modulus. Ku = K + alpha^2*M = 2.345E9
# Undrained Poisson ratio. nuu = (3Ku - 2G)/(6Ku + 2G) = 0.2364
# Skempton coefficient. B = alpha*M/Ku = 0.554
# Fluid mobility (rock permeability/fluid viscosity). k = 1E-12
[Mesh]
type = FileMesh
file = borehole_lowres_input.e
[]
[GlobalParams]
displacements = 'disp_x disp_y disp_z'
porepressure = porepressure
block = 1
[]
[GlobalParams]
volumetric_locking_correction=true
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[./porepressure]
scaling = 1E9 # Notice the scaling, to make porepressure's kernels roughly of same magnitude as disp's kernels
[../]
[]
[ICs]
[./initial_p]
type = ConstantIC
variable = porepressure
value = 1E6
[../]
[]
[BCs]
[./fixed_outer_x]
type = DirichletBC
variable = disp_x
value = 0
boundary = outer
[../]
[./fixed_outer_y]
type = DirichletBC
variable = disp_y
value = 0
boundary = outer
[../]
[./plane_strain]
type = DirichletBC
variable = disp_z
value = 0
boundary = 'zmin zmax'
[../]
[./borehole_wall]
type = DirichletBC
variable = porepressure
value = 0
boundary = bh_wall
[../]
[]
[AuxVariables]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./tot_yy]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./tot_yy]
type = ParsedAux
args = 'stress_yy porepressure'
execute_on = timestep_end
variable = tot_yy
function = 'stress_yy-0.65*porepressure'
[../]
[]
[Kernels]
[./grad_stress_x]
type = StressDivergenceTensors
variable = disp_x
component = 0
[../]
[./grad_stress_y]
type = StressDivergenceTensors
variable = disp_y
component = 1
[../]
[./grad_stress_z]
type = StressDivergenceTensors
variable = disp_z
component = 2
[../]
[./poro_x]
type = PoroMechanicsCoupling
variable = disp_x
component = 0
[../]
[./poro_y]
type = PoroMechanicsCoupling
variable = disp_y
component = 1
[../]
[./poro_z]
type = PoroMechanicsCoupling
variable = disp_z
component = 2
[../]
[./poro_timederiv]
type = PoroFullSatTimeDerivative
variable = porepressure
[../]
[./darcy_flow]
type = CoefDiffusion
variable = porepressure
coef = 1E-12
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
C_ijkl = '0.5E9 1.5E9'
# bulk modulus is lambda + 2*mu/3 = 0.5 + 2*1.5/3 = 1.5E9
fill_method = symmetric_isotropic
[../]
[./strain]
type = ComputeFiniteStrain
displacements = 'disp_x disp_y disp_z'
eigenstrain_names = ini_stress
[../]
[./ini_stress]
type = ComputeEigenstrainFromInitialStress
initial_stress = '-1.35E6 0 0 0 -3.35E6 0 0 0 0' # remember this is the effective stress
eigenstrain_name = ini_stress
[../]
[./no_plasticity]
type = ComputeFiniteStrainElasticStress
[../]
[./poro_material]
type = PoroFullSatMaterial
porosity0 = 0.3
biot_coefficient = 0.65
solid_bulk_compliance = 0.6666666666667E-9
fluid_bulk_compliance = 1.3944444444444E-9
constant_porosity = false
[../]
[]
[Postprocessors]
[./p00]
type = PointValue
variable = porepressure
point = '1.00 0 0'
outputs = csv_p
[../]
[./p01]
type = PointValue
variable = porepressure
point = '1.01 0 0'
outputs = csv_p
[../]
[./p02]
type = PointValue
variable = porepressure
point = '1.02 0 0'
outputs = csv_p
[../]
[./p03]
type = PointValue
variable = porepressure
point = '1.03 0 0'
outputs = csv_p
[../]
[./p04]
type = PointValue
variable = porepressure
point = '1.04 0 0'
outputs = csv_p
[../]
[./p05]
type = PointValue
variable = porepressure
point = '1.05 0 0'
outputs = csv_p
[../]
[./p06]
type = PointValue
variable = porepressure
point = '1.06 0 0'
outputs = csv_p
[../]
[./p07]
type = PointValue
variable = porepressure
point = '1.07 0 0'
outputs = csv_p
[../]
[./p08]
type = PointValue
variable = porepressure
point = '1.08 0 0'
outputs = csv_p
[../]
[./p09]
type = PointValue
variable = porepressure
point = '1.09 0 0'
outputs = csv_p
[../]
[./p10]
type = PointValue
variable = porepressure
point = '1.10 0 0'
outputs = csv_p
[../]
[./p11]
type = PointValue
variable = porepressure
point = '1.11 0 0'
outputs = csv_p
[../]
[./p12]
type = PointValue
variable = porepressure
point = '1.12 0 0'
outputs = csv_p
[../]
[./p13]
type = PointValue
variable = porepressure
point = '1.13 0 0'
outputs = csv_p
[../]
[./p14]
type = PointValue
variable = porepressure
point = '1.14 0 0'
outputs = csv_p
[../]
[./p15]
type = PointValue
variable = porepressure
point = '1.15 0 0'
outputs = csv_p
[../]
[./p16]
type = PointValue
variable = porepressure
point = '1.16 0 0'
outputs = csv_p
[../]
[./p17]
type = PointValue
variable = porepressure
point = '1.17 0 0'
outputs = csv_p
[../]
[./p18]
type = PointValue
variable = porepressure
point = '1.18 0 0'
outputs = csv_p
[../]
[./p19]
type = PointValue
variable = porepressure
point = '1.19 0 0'
outputs = csv_p
[../]
[./p20]
type = PointValue
variable = porepressure
point = '1.20 0 0'
outputs = csv_p
[../]
[./p21]
type = PointValue
variable = porepressure
point = '1.21 0 0'
outputs = csv_p
[../]
[./p22]
type = PointValue
variable = porepressure
point = '1.22 0 0'
outputs = csv_p
[../]
[./p23]
type = PointValue
variable = porepressure
point = '1.23 0 0'
outputs = csv_p
[../]
[./p24]
type = PointValue
variable = porepressure
point = '1.24 0 0'
outputs = csv_p
[../]
[./p25]
type = PointValue
variable = porepressure
point = '1.25 0 0'
outputs = csv_p
[../]
[./s00]
type = PointValue
variable = disp_x
point = '1.00 0 0'
outputs = csv_s
[../]
[./s01]
type = PointValue
variable = disp_x
point = '1.01 0 0'
outputs = csv_s
[../]
[./s02]
type = PointValue
variable = disp_x
point = '1.02 0 0'
outputs = csv_s
[../]
[./s03]
type = PointValue
variable = disp_x
point = '1.03 0 0'
outputs = csv_s
[../]
[./s04]
type = PointValue
variable = disp_x
point = '1.04 0 0'
outputs = csv_s
[../]
[./s05]
type = PointValue
variable = disp_x
point = '1.05 0 0'
outputs = csv_s
[../]
[./s06]
type = PointValue
variable = disp_x
point = '1.06 0 0'
outputs = csv_s
[../]
[./s07]
type = PointValue
variable = disp_x
point = '1.07 0 0'
outputs = csv_s
[../]
[./s08]
type = PointValue
variable = disp_x
point = '1.08 0 0'
outputs = csv_s
[../]
[./s09]
type = PointValue
variable = disp_x
point = '1.09 0 0'
outputs = csv_s
[../]
[./s10]
type = PointValue
variable = disp_x
point = '1.10 0 0'
outputs = csv_s
[../]
[./s11]
type = PointValue
variable = disp_x
point = '1.11 0 0'
outputs = csv_s
[../]
[./s12]
type = PointValue
variable = disp_x
point = '1.12 0 0'
outputs = csv_s
[../]
[./s13]
type = PointValue
variable = disp_x
point = '1.13 0 0'
outputs = csv_s
[../]
[./s14]
type = PointValue
variable = disp_x
point = '1.14 0 0'
outputs = csv_s
[../]
[./s15]
type = PointValue
variable = disp_x
point = '1.15 0 0'
outputs = csv_s
[../]
[./s16]
type = PointValue
variable = disp_x
point = '1.16 0 0'
outputs = csv_s
[../]
[./s17]
type = PointValue
variable = disp_x
point = '1.17 0 0'
outputs = csv_s
[../]
[./s18]
type = PointValue
variable = disp_x
point = '1.18 0 0'
outputs = csv_s
[../]
[./s19]
type = PointValue
variable = disp_x
point = '1.19 0 0'
outputs = csv_s
[../]
[./s20]
type = PointValue
variable = disp_x
point = '1.20 0 0'
outputs = csv_s
[../]
[./s21]
type = PointValue
variable = disp_x
point = '1.21 0 0'
outputs = csv_s
[../]
[./s22]
type = PointValue
variable = disp_x
point = '1.22 0 0'
outputs = csv_s
[../]
[./s23]
type = PointValue
variable = disp_x
point = '1.23 0 0'
outputs = csv_s
[../]
[./s24]
type = PointValue
variable = disp_x
point = '1.24 0 0'
outputs = csv_s
[../]
[./s25]
type = PointValue
variable = disp_x
point = '1.25 0 0'
outputs = csv_s
[../]
[./t00]
type = PointValue
variable = tot_yy
point = '1.00 0 0'
outputs = csv_t
[../]
[./t01]
type = PointValue
variable = tot_yy
point = '1.01 0 0'
outputs = csv_t
[../]
[./t02]
type = PointValue
variable = tot_yy
point = '1.02 0 0'
outputs = csv_t
[../]
[./t03]
type = PointValue
variable = tot_yy
point = '1.03 0 0'
outputs = csv_t
[../]
[./t04]
type = PointValue
variable = tot_yy
point = '1.04 0 0'
outputs = csv_t
[../]
[./t05]
type = PointValue
variable = tot_yy
point = '1.05 0 0'
outputs = csv_t
[../]
[./t06]
type = PointValue
variable = tot_yy
point = '1.06 0 0'
outputs = csv_t
[../]
[./t07]
type = PointValue
variable = tot_yy
point = '1.07 0 0'
outputs = csv_t
[../]
[./t08]
type = PointValue
variable = tot_yy
point = '1.08 0 0'
outputs = csv_t
[../]
[./t09]
type = PointValue
variable = tot_yy
point = '1.09 0 0'
outputs = csv_t
[../]
[./t10]
type = PointValue
variable = tot_yy
point = '1.10 0 0'
outputs = csv_t
[../]
[./t11]
type = PointValue
variable = tot_yy
point = '1.11 0 0'
outputs = csv_t
[../]
[./t12]
type = PointValue
variable = tot_yy
point = '1.12 0 0'
outputs = csv_t
[../]
[./t13]
type = PointValue
variable = tot_yy
point = '1.13 0 0'
outputs = csv_t
[../]
[./t14]
type = PointValue
variable = tot_yy
point = '1.14 0 0'
outputs = csv_t
[../]
[./t15]
type = PointValue
variable = tot_yy
point = '1.15 0 0'
outputs = csv_t
[../]
[./t16]
type = PointValue
variable = tot_yy
point = '1.16 0 0'
outputs = csv_t
[../]
[./t17]
type = PointValue
variable = tot_yy
point = '1.17 0 0'
outputs = csv_t
[../]
[./t18]
type = PointValue
variable = tot_yy
point = '1.18 0 0'
outputs = csv_t
[../]
[./t19]
type = PointValue
variable = tot_yy
point = '1.19 0 0'
outputs = csv_t
[../]
[./t20]
type = PointValue
variable = tot_yy
point = '1.20 0 0'
outputs = csv_t
[../]
[./t21]
type = PointValue
variable = tot_yy
point = '1.21 0 0'
outputs = csv_t
[../]
[./t22]
type = PointValue
variable = tot_yy
point = '1.22 0 0'
outputs = csv_t
[../]
[./t23]
type = PointValue
variable = tot_yy
point = '1.23 0 0'
outputs = csv_t
[../]
[./t24]
type = PointValue
variable = tot_yy
point = '1.24 0 0'
outputs = csv_t
[../]
[./t25]
type = PointValue
variable = tot_yy
point = '1.25 0 0'
outputs = csv_t
[../]
[./dt]
type = FunctionValuePostprocessor
outputs = console
function = 2*t
[../]
[]
[Preconditioning]
[./andy]
type = SMP
full = true
petsc_options = '-snes_monitor -snes_linesearch_monitor'
petsc_options_iname = '-ksp_type -pc_type -snes_atol -snes_rtol -snes_max_it -ksp_max_it -sub_pc_type -sub_pc_factor_shift_type'
petsc_options_value = 'gmres asm 1E0 1E-10 200 500 lu NONZERO'
[../]
[]
[Executioner]
type = Transient
solve_type = Newton
start_time = 0
end_time = 0.3
dt = 0.3
#[./TimeStepper]
# type = PostprocessorDT
# postprocessor = dt
# dt = 0.003
#[../]
[]
[Outputs]
execute_on = 'timestep_end'
file_base = borehole_lowres
exodus = true
sync_times = '0.003 0.3'
[./csv_p]
file_base = borehole_lowres_p
type = CSV
[../]
[./csv_s]
file_base = borehole_lowres_s
type = CSV
[../]
[./csv_t]
file_base = borehole_lowres_t
type = CSV
[../]
[]
(modules/contact/test/tests/verification/patch_tests/brick_3/brick3_template2.i)
[GlobalParams]
order = SECOND
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
file = brick3_mesh.e
[]
[Problem]
type = AugmentedLagrangianContactProblem
maximum_lagrangian_update_iterations = 200
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./penetration]
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./saved_z]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./diag_saved_z]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./inc_slip_z]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./accum_slip_z]
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y saved_z'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 4
paired_boundary = 3
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./ref_resid_x]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_x
[../]
[./ref_resid_y]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_y
[../]
[./sigma_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./sigma_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./disp_x28]
type = NodalVariableValue
nodeid = 27
variable = disp_x
[../]
[./disp_x33]
type = NodalVariableValue
nodeid = 32
variable = disp_x
[../]
[./disp_y28]
type = NodalVariableValue
nodeid = 27
variable = disp_y
[../]
[./disp_y33]
type = NodalVariableValue
nodeid = 32
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./bot_y]
type = DirichletBC
variable = disp_y
boundary = 1
value = 0.0
[../]
[./side_x]
type = DirichletBC
variable = disp_x
boundary = 2
value = 0.0
[../]
[./back_z]
type = DirichletBC
variable = disp_z
boundary = 6
value = 0.0
[../]
[./top_press]
type = Pressure
variable = disp_y
boundary = 5
factor = 109.89
[../]
[]
[Materials]
[./bot_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./bot_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./bot_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./top_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./top_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./top_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-8
nl_rel_tol = 1e-7
l_max_its = 50
nl_max_its = 100
dt = 1.0
end_time = 1.0
num_steps = 10
dtmin = 1.0
l_tol = 1e-5
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '1 3 4 5'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '1 3 4 5'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
show = 'bot_react_x bot_react_y disp_x28 disp_y28 disp_x33 disp_y33 stress_yy stress_zz top_react_x top_react_y x_disp y_disp cont_press'
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./leftright]
secondary = 3
primary = 4
normalize_penalty = true
tangential_tolerance = 1e-3
penalty = 1e+7
al_penetration_tolerance = 1e-8
[../]
[]
(modules/contact/test/tests/verification/hertz_cyl/quart_symm_q8/hertz_cyl_qsym_1deg_template1.i)
[GlobalParams]
order = SECOND
volumetric_locking_correction = false
displacements = 'disp_x disp_y'
[]
[Mesh]
file = hertz_cyl_qsym_1deg_q8.e
[]
[Problem]
type = ReferenceResidualProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./tang_force_x]
[../]
[./tang_force_y]
[../]
[]
[Functions]
[./disp_ramp_vert]
type = PiecewiseLinear
x = '0. 1. 2.'
y = '0. -0.0020 -0.0020'
[../]
[./disp_ramp_zero]
type = PiecewiseLinear
x = '0. 1. 2.'
y = '0. 0.0 0.0'
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 4
paired_boundary = 3
[../]
[./tang_force_x]
type = PenetrationAux
variable = tang_force_x
quantity = tangential_force_x
boundary = 4
paired_boundary = 3
[../]
[./tang_force_y]
type = PenetrationAux
variable = tang_force_y
quantity = tangential_force_y
boundary = 4
paired_boundary = 3
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./disp_x281]
type = NodalVariableValue
nodeid = 280
variable = disp_x
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./side_x]
type = DirichletBC
variable = disp_y
boundary = '1 3'
value = 0.0
[../]
[./bot_y]
type = DirichletBC
variable = disp_x
boundary = '1 2 3'
value = 0.0
[../]
[./top_y_disp]
type = FunctionDirichletBC
variable = disp_y
boundary = 5
function = disp_ramp_vert
[../]
[]
[Materials]
[./stuff1_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e10
poissons_ratio = 0.0
[../]
[./stuff1_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./stuff1_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./stuff2_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff2_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./stuff2_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[./stuff3_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '3'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff3_strain]
type = ComputeFiniteStrain
block = '3'
[../]
[./stuff3_stress]
type = ComputeFiniteStrainElasticStress
block = '3'
[../]
[./stuff4_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '4'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff4_strain]
type = ComputeFiniteStrain
block = '4'
[../]
[./stuff4_stress]
type = ComputeFiniteStrainElasticStress
block = '4'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-7
nl_rel_tol = 1e-6
l_max_its = 50
nl_max_its = 100
start_time = 0.0
dt = 0.1
dtmin = 0.1
num_steps = 10
end_time = 1.0
l_tol = 1e-4
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '3 4 5'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '3 4 5'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '4'
sort_by = id
[../]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
show = 'bot_react_x bot_react_y disp_x281 top_react_x top_react_y x_disp y_disp cont_press'
start_time = 0.9
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./interface]
primary = 3
secondary = 4
normalize_penalty = true
tangential_tolerance = 1e-3
penalty = 1e+11
[../]
[]
(modules/contact/test/tests/mortar_aux_kernels/block-dynamics-aux-vel.i)
starting_point = 2e-1
offset = -0.19
[GlobalParams]
displacements = 'disp_x disp_y'
[]
[Mesh]
file = long-bottom-block-1elem-blocks.e
[]
[Variables]
[disp_x]
block = '1 2'
[]
[disp_y]
block = '1 2'
[]
[normal_lm]
block = 3
use_dual = true
[]
[]
[ICs]
[disp_y]
block = 2
variable = disp_y
value = '${fparse starting_point + offset}'
type = ConstantIC
[]
[]
[Kernels]
[DynamicTensorMechanics]
displacements = 'disp_x disp_y'
generate_output = 'stress_xx stress_yy'
strain = FINITE
block = '1 2'
zeta = 1.0
alpha = 0.0
[]
[inertia_x]
type = InertialForce
variable = disp_x
velocity = vel_x
acceleration = accel_x
beta = 0.25
gamma = 0.5
alpha = 0
eta = 0.0
block = '1 2'
[]
[inertia_y]
type = InertialForce
variable = disp_y
velocity = vel_y
acceleration = accel_y
beta = 0.25
gamma = 0.5
alpha = 0
eta = 0.0
block = '1 2'
[]
[]
[Materials]
[elasticity_2]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[]
[elasticity_1]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e8
poissons_ratio = 0.3
[]
[stress]
type = ComputeFiniteStrainElasticStress
block = '1 2'
[]
[strain]
type = ComputeFiniteStrain
block = '1 2'
[]
[density]
type = GenericConstantMaterial
block = '1 2'
prop_names = 'density'
prop_values = '7750'
[]
[]
[AuxVariables]
[gap_vel]
block = '3'
[]
[vel_x]
block = '1 2'
[]
[accel_x]
block = '1 2'
[]
[vel_y]
block = '1 2'
[]
[accel_y]
block = '1 2'
[]
[vel_z]
block = '1 2'
[]
[accel_z]
block = '1 2'
[]
[]
[AuxKernels]
[gap_vel]
type = WeightedGapVelAux
variable = gap_vel
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
disp_x = disp_x
disp_y = disp_y
[]
[accel_x]
type = NewmarkAccelAux
variable = accel_x
displacement = disp_x
velocity = vel_x
beta = 0.25
execute_on = 'linear timestep_end'
[]
[vel_x]
type = NewmarkVelAux
variable = vel_x
acceleration = accel_x
gamma = 0.5
execute_on = 'linear timestep_end'
[]
[accel_y]
type = NewmarkAccelAux
variable = accel_y
displacement = disp_y
velocity = vel_y
beta = 0.25
execute_on = 'linear timestep_end'
[]
[vel_y]
type = NewmarkVelAux
variable = vel_y
acceleration = accel_y
gamma = 0.5
execute_on = 'linear timestep_end'
[]
[]
[Constraints]
[weighted_gap_lm]
type = ComputeDynamicWeightedGapLMMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = normal_lm
disp_x = disp_x
disp_y = disp_y
use_displaced_mesh = true
c = 1e4
interpolate_normals = false
capture_tolerance = 1.0e-5
newmark_beta = 0.25
newmark_gamma = 0.5
[]
[normal_x]
type = NormalMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = normal_lm
secondary_variable = disp_x
component = x
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[normal_y]
type = NormalMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = normal_lm
secondary_variable = disp_y
component = y
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[]
[BCs]
[botx]
type = DirichletBC
variable = disp_x
boundary = 40
value = 0.0
[]
[boty]
type = DirichletBC
variable = disp_y
boundary = 40
value = 0.0
[]
[topy]
type = FunctionDirichletBC
variable = disp_y
boundary = 30
function = '${starting_point} * cos(2 * pi / 4 * t) + ${offset}'
[]
[leftx]
type = FunctionDirichletBC
variable = disp_x
boundary = 50
function = '1e-2 * t'
[]
[]
[Executioner]
type = Transient
end_time = 0.1
dt = 0.05
dtmin = 0.05
solve_type = 'PJFNK'
petsc_options = '-snes_converged_reason -ksp_converged_reason -pc_svd_monitor '
'-snes_linesearch_monitor -snes_ksp_ew'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type -pc_factor_shift_type -pc_factor_shift_amount -mat_mffd_err '
petsc_options_value = 'lu superlu_dist NONZERO 1e-15 1e-5'
nl_max_its = 20
line_search = 'none'
snesmf_reuse_base = false
[TimeIntegrator]
type = NewmarkBeta
beta = 0.25
gamma = 0.5
[]
[]
[Debug]
show_var_residual_norms = true
[]
[Outputs]
exodus = true
checkpoint = true
[]
[Preconditioning]
[smp]
type = SMP
full = true
[]
[]
[Postprocessors]
active = 'num_nl cumulative contact'
[num_nl]
type = NumNonlinearIterations
[]
[cumulative]
type = CumulativeValuePostprocessor
postprocessor = num_nl
[]
[contact]
type = ContactDOFSetSize
variable = normal_lm
subdomain = '3'
execute_on = 'nonlinear timestep_end'
[]
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/patch_recovery.i)
[Mesh]
type = GeneratedMesh
dim = 2
nx = 2
ny = 2
displacements = 'ux uy'
[]
[Variables]
[ux]
[]
[uy]
[]
[]
[AuxVariables]
[stress_xx_recovered]
order = FIRST
family = LAGRANGE
[]
[stress_yy_recovered]
order = FIRST
family = LAGRANGE
[]
[]
[Functions]
[tdisp]
type = ParsedFunction
value = 0.01*t
[]
[]
[Kernels]
[TensorMechanics]
displacements = 'ux uy'
use_displaced_mesh = true
[]
[]
[AuxKernels]
[stress_xx_recovered]
type = NodalPatchRecoveryAux
variable = stress_xx_recovered
nodal_patch_recovery_uo = stress_xx_patch
execute_on = 'TIMESTEP_END'
[]
[stress_yy_recovered]
type = NodalPatchRecoveryAux
variable = stress_yy_recovered
nodal_patch_recovery_uo = stress_yy_patch
execute_on = 'TIMESTEP_END'
[]
[]
[BCs]
[symmy]
type = DirichletBC
variable = uy
boundary = bottom
value = 0
[]
[symmx]
type = DirichletBC
variable = ux
boundary = left
value = 0
[]
[tdisp]
type = FunctionDirichletBC
variable = uy
boundary = top
function = tdisp
[]
[]
[UserObjects]
[slip_rate_gss]
type = CrystalPlasticitySlipRateGSS
variable_size = 12
slip_sys_file_name = input_slip_sys.txt
num_slip_sys_flowrate_props = 2
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
uo_state_var_name = state_var_gss
[]
[slip_resistance_gss]
type = CrystalPlasticitySlipResistanceGSS
variable_size = 12
uo_state_var_name = state_var_gss
[]
[state_var_gss]
type = CrystalPlasticityStateVariable
variable_size = 12
groups = '0 4 8 12'
group_values = '60.8 60.8 60.8'
uo_state_var_evol_rate_comp_name = state_var_evol_rate_comp_gss
scale_factor = 1.0
[]
[state_var_evol_rate_comp_gss]
type = CrystalPlasticityStateVarRateComponentGSS
variable_size = 12
hprops = '1.0 541.5 109.8 2.5'
uo_slip_rate_name = slip_rate_gss
uo_state_var_name = state_var_gss
[]
[stress_xx_patch]
type = NodalPatchRecoveryMaterialProperty
patch_polynomial_order = FIRST
property = 'stress'
component = '0 0'
execute_on = 'TIMESTEP_END'
[]
[stress_yy_patch]
type = NodalPatchRecoveryMaterialProperty
patch_polynomial_order = FIRST
property = 'stress'
component = '1 1'
execute_on = 'TIMESTEP_END'
[]
[]
[Materials]
[crysp]
type = FiniteStrainUObasedCP
stol = 1e-2
tan_mod_type = exact
uo_slip_rates = 'slip_rate_gss'
uo_slip_resistances = 'slip_resistance_gss'
uo_state_vars = 'state_var_gss'
uo_state_var_evol_rate_comps = 'state_var_evol_rate_comp_gss'
[]
[strain]
type = ComputeFiniteStrain
displacements = 'ux uy'
[]
[elasticity_tensor]
type = ComputeElasticityTensorCP
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
[]
[]
[Preconditioning]
[smp]
type = SMP
full = true
[]
[]
[Executioner]
type = Transient
dt = 0.05
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
nl_abs_tol = 1e-10
nl_rel_step_tol = 1e-10
dtmax = 10.0
nl_rel_tol = 1e-10
end_time = 1
dtmin = 0.05
num_steps = 10
nl_abs_step_tol = 1e-10
[]
[Outputs]
exodus = true
[]
(modules/contact/test/tests/verification/patch_tests/brick_3/brick3_mu_0_2_pen.i)
[GlobalParams]
order = SECOND
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
file = brick3_mesh.e
[]
[Problem]
type = ReferenceResidualProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./penetration]
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./saved_z]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./diag_saved_z]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./inc_slip_z]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./accum_slip_z]
[../]
[./tang_force_x]
[../]
[./tang_force_y]
[../]
[./tang_force_z]
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y saved_z'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_end
boundary = 3
paired_boundary = 4
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_end
boundary = 3
paired_boundary = 4
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 3
paired_boundary = 4
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 3
paired_boundary = 4
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 3
paired_boundary = 4
[../]
[./tang_force_x]
type = PenetrationAux
variable = tang_force_x
quantity = tangential_force_x
boundary = 3
paired_boundary = 4
[../]
[./tang_force_y]
type = PenetrationAux
variable = tang_force_y
quantity = tangential_force_y
boundary = 3
paired_boundary = 4
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./ref_resid_x]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_x
[../]
[./ref_resid_y]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_y
[../]
[./sigma_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./sigma_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./disp_x28]
type = NodalVariableValue
nodeid = 27
variable = disp_x
[../]
[./disp_x33]
type = NodalVariableValue
nodeid = 32
variable = disp_x
[../]
[./disp_y28]
type = NodalVariableValue
nodeid = 27
variable = disp_y
[../]
[./disp_y33]
type = NodalVariableValue
nodeid = 32
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./bot_y]
type = DirichletBC
variable = disp_y
boundary = 1
value = 0.0
[../]
[./side_x]
type = DirichletBC
variable = disp_x
boundary = 2
value = 0.0
[../]
[./back_z]
type = DirichletBC
variable = disp_z
boundary = 6
value = 0.0
[../]
[./top_press]
type = Pressure
variable = disp_y
boundary = 5
factor = 109.89
[../]
[]
[Materials]
[./bot_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./bot_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./bot_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./top_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./top_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./top_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-9
nl_rel_tol = 1e-8
l_max_its = 50
nl_max_its = 100
dt = 1.0
end_time = 1.0
num_steps = 10
dtmin = 1.0
l_tol = 1e-5
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '1 3 4 5'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '1 3 4 5'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
file_base = brick3_mu_0_2_pen_out
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
file_base = brick3_mu_0_2_pen_check
show = 'bot_react_x bot_react_y disp_x28 disp_y28 disp_x33 disp_y33 stress_yy stress_zz top_react_x top_react_y x_disp y_disp cont_press'
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./leftright]
secondary = 3
primary = 4
model = coulomb
formulation = penalty
normalize_penalty = true
friction_coefficient = 0.2
penalty = 1e+6
[../]
[]
(modules/tensor_mechanics/test/tests/ad_elastic/finite_elastic-noad.i)
[Mesh]
type = GeneratedMesh
dim = 3
nx = 3
ny = 3
nz = 3
[]
[GlobalParams]
displacements = 'disp_x disp_y disp_z'
[]
[Variables]
# scale with one over Young's modulus
[./disp_x]
scaling = 1e-10
[../]
[./disp_y]
scaling = 1e-10
[../]
[./disp_z]
scaling = 1e-10
[../]
[]
[Kernels]
[./stress_x]
type = StressDivergenceTensors
component = 0
variable = disp_x
use_displaced_mesh = true
[../]
[./stress_y]
type = StressDivergenceTensors
component = 1
variable = disp_y
use_displaced_mesh = true
[../]
[./stress_z]
type = StressDivergenceTensors
component = 2
variable = disp_z
use_displaced_mesh = true
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = disp_y
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = disp_x
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = disp_z
boundary = back
value = 0
[../]
[./tdisp]
type = DirichletBC
variable = disp_z
boundary = front
value = 0.1
[../]
[]
[Materials]
[./elasticity]
type = ComputeIsotropicElasticityTensor
poissons_ratio = 0.3
youngs_modulus = 1e10
[../]
[./strain]
type = ComputeFiniteStrain
[../]
[./stress]
type = ComputeFiniteStrainElasticStress
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.05
solve_type = 'NEWTON'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomeramg
dtmin = 0.05
num_steps = 1
[]
[Outputs]
exodus = true
file_base = finite_elastic_out
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform3.i)
# apply repeated stretches in x z directions, and smaller stretches along the y direction,
# so that sigma_I = sigma_II,
# which means that lode angle = 30deg.
# The allows yield surface in meridional plane to be mapped out
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '1E-6*x*t'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0.25E-6*y*sin(t)'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z*t'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./mc_int]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./mc_int_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_internal_parameter
variable = mc_int
[../]
[./yield_fcn_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./internal]
type = PointValue
point = '0 0 0'
variable = mc_int
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = yield_fcn
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 10
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 50
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningExponential
value_0 = 0
value_residual = 0.8726646 # 50deg
rate = 3000.0
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 4
mc_edge_smoother = 20
yield_function_tolerance = 1E-8
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = mc
debug_fspb = crash
[../]
[]
[Executioner]
end_time = 30
dt = 1
type = Transient
[]
[Outputs]
file_base = small_deform3
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/contact/test/tests/verification/hertz_cyl/quart_symm_q4/hertz_cyl_qsym_1deg_template1.i)
[GlobalParams]
volumetric_locking_correction = true
displacements = 'disp_x disp_y'
[]
[Mesh]
file = hertz_cyl_qsym_1deg_q4.e
[]
[Problem]
type = ReferenceResidualProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./tang_force_x]
[../]
[./tang_force_y]
[../]
[]
[Functions]
[./disp_ramp_vert]
type = PiecewiseLinear
x = '0. 1. 2.'
y = '0. -0.0020 -0.0020'
[../]
[./disp_ramp_zero]
type = PiecewiseLinear
x = '0. 1. 2.'
y = '0. 0.0 0.0'
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 4
paired_boundary = 3
[../]
[./tang_force_x]
type = PenetrationAux
variable = tang_force_x
quantity = tangential_force_x
boundary = 4
paired_boundary = 3
[../]
[./tang_force_y]
type = PenetrationAux
variable = tang_force_y
quantity = tangential_force_y
boundary = 4
paired_boundary = 3
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./ref_resid_x]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_x
[../]
[./ref_resid_y]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_y
[../]
[./disp_x281]
type = NodalVariableValue
nodeid = 280
variable = disp_x
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./side_x]
type = DirichletBC
variable = disp_y
boundary = '1 3'
value = 0.0
[../]
[./bot_y]
type = DirichletBC
variable = disp_x
boundary = '1 2 3'
value = 0.0
[../]
[./top_y_disp]
type = FunctionDirichletBC
variable = disp_y
boundary = 5
function = disp_ramp_vert
[../]
[]
[Materials]
[./stuff1_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e10
poissons_ratio = 0.0
[../]
[./stuff1_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./stuff1_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./stuff2_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff2_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./stuff2_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[./stuff3_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '3'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff3_strain]
type = ComputeFiniteStrain
block = '3'
[../]
[./stuff3_stress]
type = ComputeFiniteStrainElasticStress
block = '3'
[../]
[./stuff4_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '4'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff4_strain]
type = ComputeFiniteStrain
block = '4'
[../]
[./stuff4_stress]
type = ComputeFiniteStrainElasticStress
block = '4'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-6
nl_rel_tol = 1e-5
l_max_its = 50
nl_max_its = 100
start_time = 0.0
dt = 0.1
dtmin = 0.1
num_steps = 10
end_time = 1.0
l_tol = 1e-3
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '3 4 5'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '3 4 5'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '4'
sort_by = id
[../]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
show = 'bot_react_x bot_react_y disp_x281 top_react_x top_react_y x_disp y_disp cont_press'
start_time = 0.9
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./interface]
primary = 3
secondary = 4
model = glued
formulation = kinematic
normalize_penalty = true
tangential_tolerance = 1e-3
penalty = 1e+9
[../]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform_hard_cubic.i)
# apply uniform stretches in x, y and z directions.
# let cohesion = 10, cohesion_residual = 2, cohesion_limit = 0.0003
# With cohesion = C, friction_angle = 60deg, tip_smoother = 4, the
# algorithm should return to
# sigma_m = (C*Cos(60) - 4)/Sin(60)
# This allows checking of the relationship for C
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '1E-6*x*t'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1E-6*y*t'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z*t'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./mc_int]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./mc_int_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_internal_parameter
variable = mc_int
[../]
[./yield_fcn_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./internal]
type = PointValue
point = '0 0 0'
variable = mc_int
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = yield_fcn
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningCubic
value_0 = 10
value_residual = 2
internal_limit = 0.0003
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 60
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 5
convert_to_radians = true
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 4
mc_edge_smoother = 25
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = mc
debug_fspb = crash
debug_jac_at_stress = '10 1 2 1 10 3 2 3 10'
debug_jac_at_pm = 1
debug_jac_at_intnl = 1E-4
debug_stress_change = 1E-5
debug_pm_change = 1E-6
debug_intnl_change = 1E-8
[../]
[]
[Executioner]
end_time = 10
dt = 0.25
type = Transient
[]
[Outputs]
file_base = small_deform_hard_cubic
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/multi/three_surface01.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 1.5
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 0E-6m in y direction and 1.5E-6 in z direction.
# trial stress_yy = 0 and stress_zz = 1.5
#
# Then SimpleTester0 should activate and the algorithm will return to
# stress_yy = 0, stress_zz = 1
# internal0 should be 0.5, and others zero
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1.5E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 1.5
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface01
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/xfem/test/tests/moving_interface/moving_bimaterial_finite_strain.i)
# This test is for two layer materials with different youngs modulus with AD
# The global stress is determined by switching the stress based on level set values
# The material interface is marked by a level set function
# The two layer materials are glued together
[GlobalParams]
displacements = 'disp_x disp_y'
[]
[XFEM]
output_cut_plane = true
[]
[UserObjects]
[level_set_cut_uo]
type = LevelSetCutUserObject
level_set_var = ls
heal_always = true
[]
[]
[Mesh]
use_displaced_mesh = true
[generated_mesh]
type = GeneratedMeshGenerator
dim = 2
nx = 10
ny = 10
xmin = 0
xmax = 5
ymin = 0
ymax = 5
elem_type = QUAD4
[]
[left_bottom]
type = ExtraNodesetGenerator
new_boundary = 'left_bottom'
coord = '0 0'
input = generated_mesh
[]
[left_top]
type = ExtraNodesetGenerator
new_boundary = 'left_top'
coord = '0 5'
input = left_bottom
[]
[]
[Functions]
[ls_func]
type = ParsedFunction
value = 'y-2.73+t'
[]
[]
[Variables]
[disp_x]
[]
[disp_y]
[]
[]
[AuxVariables]
[ls]
[]
[a_strain_xx]
order = CONSTANT
family = MONOMIAL
[]
[a_strain_yy]
order = CONSTANT
family = MONOMIAL
[]
[a_strain_xy]
order = CONSTANT
family = MONOMIAL
[]
[b_strain_xx]
order = CONSTANT
family = MONOMIAL
[]
[b_strain_yy]
order = CONSTANT
family = MONOMIAL
[]
[b_strain_xy]
order = CONSTANT
family = MONOMIAL
[]
[stress_xx]
order = CONSTANT
family = MONOMIAL
[]
[stress_yy]
order = CONSTANT
family = MONOMIAL
[]
[stress_xy]
order = CONSTANT
family = MONOMIAL
[]
[]
[AuxKernels]
[ls_function]
type = FunctionAux
variable = ls
function = ls_func
[]
[a_strain_xx]
type = RankTwoAux
variable = a_strain_xx
rank_two_tensor = A_total_strain
index_i = 0
index_j = 0
[]
[a_strain_yy]
type = RankTwoAux
variable = a_strain_yy
rank_two_tensor = A_total_strain
index_i = 1
index_j = 1
[]
[a_strain_xy]
type = RankTwoAux
variable = a_strain_xy
rank_two_tensor = A_total_strain
index_i = 0
index_j = 1
[]
[b_strain_xx]
type = RankTwoAux
variable = b_strain_xx
rank_two_tensor = B_total_strain
index_i = 0
index_j = 0
[]
[b_strain_yy]
type = RankTwoAux
variable = b_strain_yy
rank_two_tensor = B_total_strain
index_i = 1
index_j = 1
[]
[b_strain_xy]
type = RankTwoAux
variable = b_strain_xy
rank_two_tensor = B_total_strain
index_i = 0
index_j = 1
[]
[stress_xx]
type = RankTwoAux
variable = stress_xx
rank_two_tensor = stress
index_i = 0
index_j = 0
[]
[stress_xy]
type = RankTwoAux
variable = stress_xy
rank_two_tensor = stress
index_i = 0
index_j = 1
[]
[stress_yy]
type = RankTwoAux
variable = stress_yy
rank_two_tensor = stress
index_i = 1
index_j = 1
[]
[]
[Kernels]
[solid_x]
type = StressDivergenceTensors
variable = disp_x
component = 0
use_displaced_mesh = true
[]
[solid_y]
type = StressDivergenceTensors
variable = disp_y
component = 1
use_displaced_mesh = true
[]
[]
[Constraints]
[dispx_constraint]
type = XFEMSingleVariableConstraint
use_displaced_mesh = false
variable = disp_x
alpha = 1e8
geometric_cut_userobject = 'level_set_cut_uo'
[]
[dispy_constraint]
type = XFEMSingleVariableConstraint
use_displaced_mesh = false
variable = disp_y
alpha = 1e8
geometric_cut_userobject = 'level_set_cut_uo'
[]
[]
[BCs]
[bottomx]
type = DirichletBC
boundary = bottom
variable = disp_x
value = 0.0
[]
[bottomy]
type = DirichletBC
boundary = bottom
variable = disp_y
value = 0.0
[]
[topx]
type = FunctionDirichletBC
boundary = top
variable = disp_x
function = 0.03*t
[]
[topy]
type = FunctionDirichletBC
boundary = top
variable = disp_y
function = '0.03*t'
[]
[]
[Materials]
[elasticity_tensor_A]
type = ComputeIsotropicElasticityTensor
base_name = A
youngs_modulus = 1e9
poissons_ratio = 0.3
[]
[strain_A]
type = ComputeFiniteStrain
base_name = A
[]
[stress_A]
type = ComputeFiniteStrainElasticStress
base_name = A
[]
[elasticity_tensor_B]
type = ComputeIsotropicElasticityTensor
base_name = B
youngs_modulus = 1e7
poissons_ratio = 0.3
[]
[strain_B]
type = ComputeFiniteStrain
base_name = B
[]
[stress_B]
type = ComputeFiniteStrainElasticStress
base_name = B
[]
[combined_stress]
type = LevelSetBiMaterialRankTwo
levelset_positive_base = 'A'
levelset_negative_base = 'B'
level_set_var = ls
prop_name = stress
[]
[combined_jacob_mult]
type = LevelSetBiMaterialRankFour
levelset_positive_base = 'A'
levelset_negative_base = 'B'
level_set_var = ls
prop_name = Jacobian_mult
[]
[]
[Postprocessors]
[disp_x_norm]
type = ElementL2Norm
variable = disp_x
[]
[disp_y_norm]
type = ElementL2Norm
variable = disp_y
[]
[]
[Executioner]
type = Transient
solve_type = NEWTON
petsc_options_iname = '-pc_type'
petsc_options_value = 'lu'
automatic_scaling = true
# controls for nonlinear iterations
nl_max_its = 15
nl_rel_tol = 1e-13
nl_abs_tol = 1e-50
# time control
start_time = 0.0
dt = 0.1
num_steps = 4
max_xfem_update = 1
[]
[Outputs]
print_linear_residuals = false
exodus = true
[]
(modules/contact/test/tests/glued/glued_contact_mechanical_constraint_test.i)
# This is a mechanical constraint (contact formulation) version of glued_contact_mechanical_constraint.i
[Mesh]
file = glued_contact_test.e
[]
[GlobalParams]
volumetric_locking_correction = true
displacements = 'disp_x disp_y disp_z'
[]
[Functions]
[./up]
type = PiecewiseLinear
x = '0 1'
y = '0 0.5001'
[../]
[./lateral]
type = PiecewiseLinear
x = '0 1 2 3'
y = '0 0 1 0'
scale_factor = 0.5
[../]
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
[../]
[]
[Contact]
[./dummy_name]
primary = 2
secondary = 3
penalty = 1e6
model = glued
formulation = kinematic
[../]
[]
[BCs]
[./bottom_lateral]
type = FunctionDirichletBC
variable = disp_x
boundary = 1
function = lateral
[../]
[./bottom_up]
type = FunctionDirichletBC
variable = disp_y
boundary = 1
function = up
[../]
[./bottom_out]
type = DirichletBC
variable = disp_z
boundary = 1
value = 0.0
[../]
[./top]
type = DirichletBC
variable = disp_y
boundary = 4
value = 0.0
[../]
[]
[Materials]
[./stiffStuff1]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stiffStuff1_strain]
type= ComputeFiniteStrain
block = '1'
[../]
[./stiffStuff1_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./stiffStuff2]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stiffStuff2_strain]
type= ComputeFiniteStrain
block = '2'
[../]
[./stiffStuff2_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
#petsc_options_iname = '-pc_type -pc_hypre_type -snes_type -snes_ls -snes_linesearch_type -ksp_gmres_restart'
#petsc_options_value = 'hypre boomeramg ls basic basic 101'
petsc_options_iname = '-pc_type -ksp_gmres_restart'
petsc_options_value = 'ilu 101'
line_search = 'none'
nl_abs_tol = 1e-8
nl_rel_tol = 1e-8
l_tol = 1e-4
l_max_its = 100
nl_max_its = 10
dt = 0.1
num_steps = 30
[./Predictor]
type = SimplePredictor
scale = 1.0
[../]
[]
[Postprocessors]
active = ''
[./resid]
type = Residual
[../]
[./iters]
type = NumNonlinearIterations
[../]
[]
[Outputs]
file_base = mechanical_constraint_out
exodus = true
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/crysp_substep.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'ux uy uz'
[]
[Variables]
[./ux]
block = 0
[../]
[./uy]
block = 0
[../]
[./uz]
block = 0
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./rotout]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./e_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./gss1]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'ux uy uz'
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./e_zz]
type = RankTwoAux
variable = e_zz
rank_two_tensor = lage
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./gss1]
type = MaterialStdVectorAux
variable = gss1
property = gss
index = 0
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = uy
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = ux
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = uz
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = uz
boundary = front
function = tdisp
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainCrystalPlasticity
block = 0
gtol = 1e-2
slip_sys_file_name = input_slip_sys.txt
nss = 12
num_slip_sys_flowrate_props = 2 #Number of properties in a slip system
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
hprops = '1.0 541.5 60.8 109.8 2.5'
gprops = '1 4 60.8 5 8 60.8 9 12 60.8'
tan_mod_type = exact
gen_random_stress_flag = false
maximum_substep_iteration = 2
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
block = 0
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'ux uy uz'
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./e_zz]
type = ElementAverageValue
variable = e_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./gss1]
type = ElementAverageValue
variable = gss1
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type'
petsc_options_value = 'lu'
nl_rel_tol = 1e-10
nl_abs_tol = 1e-10
dt = 0.5
dtmax = 10.0
dtmin = 0.5
num_steps = 3
[]
[Outputs]
file_base = crysp_substep_out
exodus = true
csv = true
gnuplot = true
[]
(modules/tensor_mechanics/test/tests/multi/special_rock1.i)
# Plasticity models:
# Mohr-Coulomb with cohesion = 40MPa, friction angle = 35deg, dilation angle = 5deg
# Tensile with strength = 1MPa
#
# Lame lambda = 1GPa. Lame mu = 1.3GPa
#
# A line of elements is perturbed randomly, and return to the yield surface at each quadpoint is checked
#
# NOTE: The yield function tolerances here are set at 100-times what i would usually use
# This is because otherwise the test fails on the 'pearcey' architecture.
# This is because identical stress tensors yield slightly different eigenvalues
# (and hence return-map residuals) on 'pearcey' than elsewhere, which results in
# a different number of NR iterations are needed to return to the yield surface.
# This is presumably because of compiler internals, or the BLAS routines being
# optimised differently or something similar.
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1000
ny = 125
nz = 1
xmin = 0
xmax = 1000
ymin = 0
ymax = 125
zmin = 0
zmax = 1
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[GlobalParams]
volumetric_locking_correction=true
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[ICs]
[./x]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_x
[../]
[./y]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_y
[../]
[./z]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_z
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./linesearch]
order = CONSTANT
family = MONOMIAL
[../]
[./ld]
order = CONSTANT
family = MONOMIAL
[../]
[./constr_added]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./linesearch]
type = MaterialRealAux
property = plastic_linesearch_needed
variable = linesearch
[../]
[./ld]
type = MaterialRealAux
property = plastic_linear_dependence_encountered
variable = ld
[../]
[./constr_added]
type = MaterialRealAux
property = plastic_constraints_added
variable = constr_added
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./max_iter]
type = ElementExtremeValue
variable = iter
outputs = console
[../]
[./av_linesearch]
type = ElementAverageValue
variable = linesearch
outputs = 'console csv'
[../]
[./av_ld]
type = ElementAverageValue
variable = ld
outputs = 'console csv'
[../]
[./av_constr_added]
type = ElementAverageValue
variable = constr_added
outputs = 'console csv'
[../]
[./av_iter]
type = ElementAverageValue
variable = iter
outputs = 'console csv'
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 4E7
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 35
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 5
convert_to_radians = true
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulombMulti
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
use_custom_returnMap = false
yield_function_tolerance = 1.0E+2 # Note larger value
shift = 1.0E+2 # Note larger value
internal_constraint_tolerance = 1.0E-7
[../]
[./mc_smooth]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 4E6
yield_function_tolerance = 1.0
internal_constraint_tolerance = 1.0E-7
[../]
[./ts]
type = TensorMechanicsHardeningConstant
value = 1E6
[../]
[./tensile]
type = TensorMechanicsPlasticTensileMulti
tensile_strength = ts
yield_function_tolerance = 1.0E+2 # Note larger value
shift = 1.0E+2 # Note larger value
internal_constraint_tolerance = 1.0E-7
use_custom_returnMap = false
use_custom_cto = false
[../]
[./tensile_smooth]
type = TensorMechanicsPlasticTensile
tensile_strength = ts
tensile_tip_smoother = 1E5
yield_function_tolerance = 1.0
internal_constraint_tolerance = 1.0E-7
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '1.0E9 1.3E9'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-5 # Note larger value, to match the larger yield_function_tolerances
plastic_models = 'tensile mc'
max_NR_iterations = 5
specialIC = 'rock'
deactivation_scheme = 'safe'
min_stepsize = 1
max_stepsize_for_dumb = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1 1 1'
debug_jac_at_intnl = '1 1 1 1'
debug_stress_change = 1E1
debug_pm_change = '1E-6 1E-6 1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6 1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = special_rock1
exodus = false
csv = true
[]
(modules/tensor_mechanics/test/tests/j2_plasticity/small_deform3.i)
# UserObject J2 test
# apply uniform compression in x direction to give
# trial stress_xx = -7, so sqrt(3*J2) = 7
# with zero Poisson's ratio, this should return to
# stress_xx = -3, stress_yy = -2 = stress_zz
# (note that stress_xx - stress_yy = stress_xx - stress_zz = -1, so sqrt(3*j2) = 1,
# and that the mean stress remains = -7/3)
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '-3.5E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = f
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = f
[../]
[./iter]
type = PointValue
point = '0 0 0'
variable = iter
[../]
[]
[UserObjects]
[./str]
type = TensorMechanicsHardeningConstant
value = 1
[../]
[./j2]
type = TensorMechanicsPlasticJ2
yield_strength = str
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = j2
debug_fspb = crash
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = small_deform3
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/crysp_user_object.i)
[Mesh]
type = GeneratedMesh
dim = 2
elem_type = QUAD4
displacements = 'disp_x disp_y'
nx = 2
ny = 2
[]
[Variables]
[./disp_x]
block = 0
[../]
[./disp_y]
block = 0
[../]
[]
[GlobalParams]
volumetric_locking_correction=true
[]
[AuxVariables]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./e_yy]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./fp_yy]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./rotout]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./gss1]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[UserObjects]
[./prop_read]
type = PropertyReadFile
prop_file_name = 'euler_ang_file.txt'
# Enter file data as prop#1, prop#2, .., prop#nprop
nprop = 3
read_type = element
[../]
[]
[AuxKernels]
[./stress_yy]
type = RankTwoAux
variable = stress_yy
rank_two_tensor = stress
index_j = 1
index_i = 1
execute_on = timestep_end
block = 0
[../]
[./e_yy]
type = RankTwoAux
variable = e_yy
rank_two_tensor = lage
index_j = 1
index_i = 1
execute_on = timestep_end
block = 0
[../]
[./fp_yy]
type = RankTwoAux
variable = fp_yy
rank_two_tensor = fp
index_j = 1
index_i = 1
execute_on = timestep_end
block = 0
[../]
[./gss1]
type = MaterialStdVectorAux
variable = gss1
property = gss
index = 0
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./fix_x]
type = DirichletBC
variable = disp_x
boundary = 'left'
value = 0
[../]
[./fix_y]
type = DirichletBC
variable = disp_y
boundary = 'bottom'
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_y
boundary = top
function = tdisp
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainCrystalPlasticity
block = 0
gtol = 1e-2
slip_sys_file_name = input_slip_sys.txt
nss = 12
num_slip_sys_flowrate_props = 2 #Number of properties in a slip system
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
hprops = '1.0 541.5 60.8 109.8 2.5'
gprops = '1 4 60.8 5 8 60.8 9 12 60.8'
tan_mod_type = exact
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
block = 0
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
read_prop_user_object = prop_read
[../]
[]
[Postprocessors]
[./stress_yy]
type = ElementAverageValue
variable = stress_yy
block = 'ANY_BLOCK_ID 0'
[../]
[./e_yy]
type = ElementAverageValue
variable = e_yy
block = 'ANY_BLOCK_ID 0'
[../]
[./fp_yy]
type = ElementAverageValue
variable = fp_yy
block = 'ANY_BLOCK_ID 0'
[../]
[./gss1]
type = ElementAverageValue
variable = gss1
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type'
petsc_options_value = 'lu'
nl_rel_tol = 1e-10
nl_abs_tol = 1e-10
dt = 0.01
dtmax = 10.0
dtmin = 0.01
num_steps = 10
[]
[Outputs]
file_base = crysp_user_object_out
exodus = true
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y'
use_displaced_mesh = true
[../]
[]
(modules/combined/test/tests/cavity_pressure/initial_temperature.i)
#
# Cavity Pressure Test
#
# This test is designed to compute an internal pressure based on
# p = n * R * T / V
# where
# p is the pressure
# n is the amount of material in the volume (moles)
# R is the universal gas constant
# T is the temperature
# V is the volume
#
# The mesh is composed of one block (1) with an interior cavity of volume 8.
# Block 2 sits in the cavity and has a volume of 1. Thus, the total
# initial volume is 7.
# The test adjusts n, T, and V in the following way:
# n => n0 + alpha * t
# T => T0 + beta * t
# V => V0 + gamma * t
# with
# alpha = n0
# beta = T0 / 2
# gamma = -(0.003322259...) * V0
# T0 = 240.54443866068704
# V0 = 7
# n0 = f(p0)
# p0 = 100
# R = 8.314472 J * K^(-1) * mol^(-1)
#
# So, n0 = p0 * V0 / R / T0 = 100 * 7 / 8.314472 / 240.544439
# = 0.35
#
# The parameters combined at t = 1 gives p = 301.
#
# This test sets the initial temperature to 500, but the CavityPressure
# is told that that initial temperature is T0. Thus, the final solution
# is unchanged.
[GlobalParams]
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
file = 3d.e
[]
[GlobalParams]
volumetric_locking_correction = true
[]
[Functions]
[./displ_positive]
type = PiecewiseLinear
x = '0 1'
y = '0 0.0029069767441859684'
[../]
[./displ_negative]
type = PiecewiseLinear
x = '0 1'
y = '0 -0.0029069767441859684'
[../]
[./temp1]
type = PiecewiseLinear
x = '0 1'
y = '1 1.5'
scale_factor = 240.54443866068704
[../]
[./material_input_function]
type = PiecewiseLinear
x = '0 1'
y = '0 0.35'
[../]
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[./temp]
initial_condition = 500
[../]
[./material_input]
[../]
[]
[AuxVariables]
[./pressure_residual_x]
[../]
[./pressure_residual_y]
[../]
[./pressure_residual_z]
[../]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zx]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
[../]
[./heat]
type = Diffusion
variable = temp
use_displaced_mesh = true
[../]
[./material_input_dummy]
type = Diffusion
variable = material_input
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
index_i = 0
index_j = 0
variable = stress_xx
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
index_i = 1
index_j = 1
variable = stress_yy
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
index_i = 2
index_j = 2
variable = stress_zz
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
index_i = 0
index_j = 1
variable = stress_xy
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
index_i = 1
index_j = 2
variable = stress_yz
[../]
[./stress_zx]
type = RankTwoAux
rank_two_tensor = stress
index_i = 2
index_j = 0
variable = stress_zx
[../]
[]
[BCs]
[./no_x_exterior]
type = DirichletBC
variable = disp_x
boundary = '7 8'
value = 0.0
[../]
[./no_y_exterior]
type = DirichletBC
variable = disp_y
boundary = '9 10'
value = 0.0
[../]
[./no_z_exterior]
type = DirichletBC
variable = disp_z
boundary = '11 12'
value = 0.0
[../]
[./prescribed_left]
type = FunctionDirichletBC
variable = disp_x
boundary = 13
function = displ_positive
[../]
[./prescribed_right]
type = FunctionDirichletBC
variable = disp_x
boundary = 14
function = displ_negative
[../]
[./no_y]
type = DirichletBC
variable = disp_y
boundary = '15 16'
value = 0.0
[../]
[./no_z]
type = DirichletBC
variable = disp_z
boundary = '17 18'
value = 0.0
[../]
[./no_x_interior]
type = DirichletBC
variable = disp_x
boundary = '1 2'
value = 0.0
[../]
[./no_y_interior]
type = DirichletBC
variable = disp_y
boundary = '3 4'
value = 0.0
[../]
[./no_z_interior]
type = DirichletBC
variable = disp_z
boundary = '5 6'
value = 0.0
[../]
[./temperatureInterior]
type = FunctionDirichletBC
boundary = 100
function = temp1
variable = temp
[../]
[./MaterialInput]
type = FunctionDirichletBC
boundary = '100 13 14 15 16'
function = material_input_function
variable = material_input
[../]
[./CavityPressure]
[./1]
boundary = 100
initial_pressure = 100
material_input = materialInput
R = 8.314472
temperature = aveTempInterior
initial_temperature = 240.54443866068704
volume = internalVolume
startup_time = 0.5
output = ppress
save_in = 'pressure_residual_x pressure_residual_y pressure_residual_z'
[../]
[../]
[]
[Materials]
[./elast_tensor1]
type = ComputeElasticityTensor
C_ijkl = '0 5'
fill_method = symmetric_isotropic
block = 1
[../]
[./strain1]
type = ComputeFiniteStrain
block = 1
[../]
[./stress1]
type = ComputeFiniteStrainElasticStress
block = 1
[../]
[./elast_tensor2]
type = ComputeElasticityTensor
C_ijkl = '0 5'
fill_method = symmetric_isotropic
block = 2
[../]
[./strain2]
type = ComputeFiniteStrain
block = 2
[../]
[./stress2]
type = ComputeFiniteStrainElasticStress
block = 2
[../]
[]
[Executioner]
type = Transient
petsc_options_iname = '-pc_type -sub_pc_type'
petsc_options_value = 'asm lu'
nl_rel_tol = 1e-12
l_tol = 1e-12
l_max_its = 20
dt = 0.5
end_time = 1.0
[]
[Postprocessors]
[./internalVolume]
type = InternalVolume
boundary = 100
execute_on = 'initial linear'
[../]
[./aveTempInterior]
type = SideAverageValue
boundary = 100
variable = temp
execute_on = 'initial linear'
[../]
[./materialInput]
type = SideAverageValue
boundary = '7 8 9 10 11 12'
variable = material_input
execute_on = linear
[../]
[]
[Outputs]
exodus = true
[]
(modules/combined/test/tests/cavity_pressure/multiple_postprocessors.i)
#
# Cavity Pressure Test (Volume input as a vector of postprocessors)
#
# This test is designed to compute an internal pressure based on
# p = n * R * T / V
# where
# p is the pressure
# n is the amount of material in the volume (moles)
# R is the universal gas constant
# T is the temperature
# V is the volume
#
# The mesh is composed of one block (1) with an interior cavity of volume 8.
# Block 2 sits in the cavity and has a volume of 1. Thus, the total
# initial volume is 7.
# The test adjusts n, T, and V in the following way:
# n => n0 + alpha * t
# T => T0 + beta * t
# V => V0 + gamma * t
# with
# alpha = n0
# beta = T0 / 2
# gamma = - (0.003322259...) * V0
# T0 = 240.54443866068704
# V0 = 7
# n0 = f(p0)
# p0 = 100
# R = 8.314472 J * K^(-1) * mol^(-1)
#
# So, n0 = p0 * V0 / R / T0 = 100 * 7 / 8.314472 / 240.544439
# = 0.35
#
# In this test the internal volume is calculated as the sum of two Postprocessors
# internalVolumeInterior and internalVolumeExterior. This sum equals the value
# reported by the internalVolume postprocessor.
#
# The parameters combined at t = 1 gives p = 301.
#
[GlobalParams]
displacements = 'disp_x disp_y disp_z'
volumetric_locking_correction = true
[]
[Mesh]
file = 3d.e
[]
[Functions]
[./displ_positive]
type = PiecewiseLinear
x = '0 1'
y = '0 0.0029069767441859684'
[../]
[./displ_negative]
type = PiecewiseLinear
x = '0 1'
y = '0 -0.0029069767441859684'
[../]
[./temp1]
type = PiecewiseLinear
x = '0 1'
y = '1 1.5'
scale_factor = 240.54443866068704
[../]
[./material_input_function]
type = PiecewiseLinear
x = '0 1'
y = '0 0.35'
[../]
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[./temp]
initial_condition = 240.54443866068704
[../]
[./material_input]
[../]
[]
[AuxVariables]
[./pressure_residual_x]
[../]
[./pressure_residual_y]
[../]
[./pressure_residual_z]
[../]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zx]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
[../]
[./heat]
type = Diffusion
variable = temp
use_displaced_mesh = true
[../]
[./material_input_dummy]
type = Diffusion
variable = material_input
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
index_i = 0
index_j = 0
variable = stress_xx
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
index_i = 1
index_j = 1
variable = stress_yy
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
index_i = 2
index_j = 2
variable = stress_zz
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
index_i = 0
index_j = 1
variable = stress_xy
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
index_i = 1
index_j = 2
variable = stress_yz
[../]
[./stress_zx]
type = RankTwoAux
rank_two_tensor = stress
index_i = 2
index_j = 0
variable = stress_zx
[../]
[]
[BCs]
[./no_x_exterior]
type = DirichletBC
variable = disp_x
boundary = '7 8'
value = 0.0
[../]
[./no_y_exterior]
type = DirichletBC
variable = disp_y
boundary = '9 10'
value = 0.0
[../]
[./no_z_exterior]
type = DirichletBC
variable = disp_z
boundary = '11 12'
value = 0.0
[../]
[./prescribed_left]
type = FunctionDirichletBC
variable = disp_x
boundary = 13
function = displ_positive
[../]
[./prescribed_right]
type = FunctionDirichletBC
variable = disp_x
boundary = 14
function = displ_negative
[../]
[./no_y]
type = DirichletBC
variable = disp_y
boundary = '15 16'
value = 0.0
[../]
[./no_z]
type = DirichletBC
variable = disp_z
boundary = '17 18'
value = 0.0
[../]
[./no_x_interior]
type = DirichletBC
variable = disp_x
boundary = '1 2'
value = 0.0
[../]
[./no_y_interior]
type = DirichletBC
variable = disp_y
boundary = '3 4'
value = 0.0
[../]
[./no_z_interior]
type = DirichletBC
variable = disp_z
boundary = '5 6'
value = 0.0
[../]
[./temperatureInterior]
type = FunctionDirichletBC
boundary = 100
function = temp1
variable = temp
[../]
[./MaterialInput]
type = FunctionDirichletBC
boundary = '100 13 14 15 16'
function = material_input_function
variable = material_input
[../]
[./CavityPressure]
[./1]
boundary = 100
initial_pressure = 100
material_input = materialInput
R = 8.314472
temperature = aveTempInterior
volume = 'internalVolumeInterior internalVolumeExterior'
startup_time = 0.5
output = ppress
save_in = 'pressure_residual_x pressure_residual_y pressure_residual_z'
[../]
[../]
[]
[Materials]
[./elast_tensor1]
type = ComputeIsotropicElasticityTensor
youngs_modulus = 1e1
poissons_ratio = 0
block = 1
[../]
[./strain1]
type = ComputeFiniteStrain
block = 1
[../]
[./stress1]
type = ComputeFiniteStrainElasticStress
block = 1
[../]
[./elast_tensor2]
type = ComputeIsotropicElasticityTensor
youngs_modulus = 1e6
poissons_ratio = 0
block = 2
[../]
[./strain2]
type = ComputeFiniteStrain
block = 2
[../]
[./stress2]
type = ComputeFiniteStrainElasticStress
block = 2
[../]
[]
[Executioner]
type = Transient
petsc_options_iname = '-pc_type -sub_pc_type'
petsc_options_value = 'asm lu'
nl_rel_tol = 1e-12
l_tol = 1e-12
l_max_its = 20
dt = 0.5
end_time = 1.0
[]
[Postprocessors]
[./internalVolume]
type = InternalVolume
boundary = 100
execute_on = 'initial linear'
[../]
[./aveTempInterior]
type = SideAverageValue
boundary = 100
variable = temp
execute_on = 'initial linear'
[../]
[./internalVolumeInterior]
type = InternalVolume
boundary = '1 2 3 4 5 6'
execute_on = 'initial linear'
[../]
[./internalVolumeExterior]
type = InternalVolume
boundary = '13 14 15 16 17 18'
execute_on = 'initial linear'
[../]
[./materialInput]
type = SideAverageValue
boundary = '7 8 9 10 11 12'
variable = material_input
execute_on = linear
[../]
[]
[Outputs]
exodus = true
[]
(modules/contact/test/tests/mortar_aux_kernels/block-dynamics-aux-fretting-wear-test.i)
starting_point = 0.5e-1
offset = -0.045
[GlobalParams]
displacements = 'disp_x disp_y'
[]
[Mesh]
file = long-bottom-block-1elem-blocks.e
[]
[Variables]
[disp_x]
block = '1 2'
[]
[disp_y]
block = '1 2'
[]
[normal_lm]
block = 3
use_dual = true
# scaling = 1.0e-5
[]
[frictional_lm]
block = 3
use_dual = true
# scaling = 1.0e-5
[]
[]
[ICs]
[disp_y]
block = 2
variable = disp_y
value = '${fparse starting_point + offset}'
type = ConstantIC
[]
[]
[Kernels]
[DynamicTensorMechanics]
displacements = 'disp_x disp_y'
generate_output = 'stress_xx stress_yy'
strain = FINITE
block = '1 2'
zeta = 1.0
hht_alpha = 0.0
[]
[inertia_x]
type = InertialForce
variable = disp_x
velocity = vel_x
acceleration = accel_x
beta = 0.25
gamma = 0.5
alpha = 0
eta = 0.0
block = '1 2'
[]
[inertia_y]
type = InertialForce
variable = disp_y
velocity = vel_y
acceleration = accel_y
beta = 0.25
gamma = 0.5
alpha = 0
eta = 0.0
block = '1 2'
[]
[]
[Materials]
[elasticity_2]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[]
[elasticity_1]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e8
poissons_ratio = 0.3
[]
[stress]
type = ComputeFiniteStrainElasticStress
block = '1 2'
[]
[strain]
type = ComputeFiniteStrain
block = '1 2'
[]
[density]
type = GenericConstantMaterial
block = '1 2'
prop_names = 'density'
prop_values = '7750'
[]
[]
[AuxVariables]
[worn_depth]
block = '3'
[]
[gap_vel]
block = '3'
[]
[vel_x]
block = '1 2'
[]
[accel_x]
block = '1 2'
[]
[vel_y]
block = '1 2'
[]
[accel_y]
block = '1 2'
[]
[vel_z]
block = '1 2'
[]
[accel_z]
block = '1 2'
[]
[]
[AuxKernels]
[gap_vel]
type = WeightedGapVelAux
variable = gap_vel
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
disp_x = disp_x
disp_y = disp_y
[]
[worn_depth]
type = MortarArchardsLawAux
variable = worn_depth
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
displacements = 'disp_x disp_y'
friction_coefficient = 0.5
energy_wear_coefficient = 1.0e-6
normal_pressure = normal_lm
execute_on = 'LINEAR NONLINEAR'
[]
[accel_x]
type = NewmarkAccelAux
variable = accel_x
displacement = disp_x
velocity = vel_x
beta = 0.25
execute_on = 'linear timestep_end'
[]
[vel_x]
type = NewmarkVelAux
variable = vel_x
acceleration = accel_x
gamma = 0.5
execute_on = 'linear timestep_end'
[]
[accel_y]
type = NewmarkAccelAux
variable = accel_y
displacement = disp_y
velocity = vel_y
beta = 0.25
execute_on = 'linear timestep_end'
[]
[vel_y]
type = NewmarkVelAux
variable = vel_y
acceleration = accel_y
gamma = 0.5
execute_on = 'linear timestep_end'
[]
[]
[Constraints]
[weighted_gap_lm]
type = ComputeDynamicFrictionalForceLMMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = normal_lm
disp_x = disp_x
disp_y = disp_y
use_displaced_mesh = true
wear_depth = worn_depth
c = 1e6
c_t = 1e6
normalize_c = true
mu = 0.5
friction_lm = frictional_lm
interpolate_normals = false
capture_tolerance = 1.0e-5
newmark_beta = 0.25
newmark_gamma = 0.5
[]
[normal_x]
type = NormalMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = normal_lm
secondary_variable = disp_x
component = x
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[normal_y]
type = NormalMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = normal_lm
secondary_variable = disp_y
component = y
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[tangential_x]
type = TangentialMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = frictional_lm
secondary_variable = disp_x
component = x
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[tangential_y]
type = TangentialMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = frictional_lm
secondary_variable = disp_y
component = y
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[]
[BCs]
[botx]
type = DirichletBC
variable = disp_x
boundary = 40
value = 0.0
[]
[boty]
type = DirichletBC
variable = disp_y
boundary = 40
value = 0.0
[]
[topy]
type = FunctionDirichletBC
variable = disp_y
boundary = 30
function = '${starting_point} * cos(4.0 * pi / 4 * t) + ${offset}'
[]
[leftx]
type = FunctionDirichletBC
variable = disp_x
boundary = 50
function = '1e-2 * (cos(32.0 * pi / 4 * t) - 1.0)'
[]
[]
[Executioner]
type = Transient
end_time = 0.5
dt = 0.05
dtmin = .002
solve_type = 'NEWTON'
petsc_options = '-snes_converged_reason -ksp_converged_reason -pc_svd_monitor '
'-snes_linesearch_monitor -snes_ksp_ew'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type -pc_factor_shift_type -pc_factor_shift_amount'
petsc_options_value = 'lu superlu_dist NONZERO 1e-15'
nl_max_its = 40
l_max_its = 15
line_search = 'l2'
snesmf_reuse_base = true
[TimeIntegrator]
type = NewmarkBeta
beta = 0.25
gamma = 0.5
[]
[]
[Debug]
show_var_residual_norms = true
[]
[Outputs]
exodus = true
checkpoint = true
[]
[Preconditioning]
[smp]
type = SMP
full = true
[]
[]
[Postprocessors]
active = 'num_nl cumulative contact'
[num_nl]
type = NumNonlinearIterations
[]
[cumulative]
type = CumulativeValuePostprocessor
postprocessor = num_nl
[]
[contact]
type = ContactDOFSetSize
variable = normal_lm
subdomain = '3'
execute_on = 'nonlinear timestep_end'
[]
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/user_object_Voce_BCC.i)
[Mesh]
type = GeneratedMesh
dim = 2
elem_type = QUAD4
displacements = 'disp_x disp_y'
nx = 2
ny = 2
[]
[GlobalParams]
volumetric_locking_correction = true
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y'
use_displaced_mesh = true
[../]
[]
[AuxVariables]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./e_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./fp_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./gss]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[UserObjects]
[./prop_read]
type = PropertyReadFile
prop_file_name = 'euler_ang_file.txt'
# Enter file data as prop#1, prop#2, .., prop#nprop
nprop = 3
read_type = element
[../]
[]
[AuxKernels]
[./stress_yy]
type = RankTwoAux
variable = stress_yy
rank_two_tensor = stress
index_j = 1
index_i = 1
execute_on = timestep_end
[../]
[./e_yy]
type = RankTwoAux
variable = e_yy
rank_two_tensor = lage
index_j = 1
index_i = 1
execute_on = timestep_end
[../]
[./fp_yy]
type = RankTwoAux
variable = fp_yy
rank_two_tensor = fp
index_j = 1
index_i = 1
execute_on = timestep_end
[../]
[./gss]
type = MaterialStdVectorAux
variable = gss
property = state_var_gss
index = 0
execute_on = timestep_end
[../]
[]
[BCs]
[./fix_x]
type = DirichletBC
variable = disp_x
boundary = 'left'
value = 0
[../]
[./fix_y]
type = DirichletBC
variable = disp_y
boundary = 'bottom'
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_y
boundary = top
function = tdisp
[../]
[]
[UserObjects]
[./slip_rate_gss]
type = CrystalPlasticitySlipRateGSS
variable_size = 48
slip_sys_file_name = input_slip_sys_bcc48.txt
num_slip_sys_flowrate_props = 2
flowprops = '1 12 0.001 0.1 13 24 0.001 0.1 25 48 0.001 0.1'
uo_state_var_name = state_var_gss
[../]
[./slip_resistance_gss]
type = CrystalPlasticitySlipResistanceGSS
variable_size = 48
uo_state_var_name = state_var_gss
[../]
[./state_var_gss]
type = CrystalPlasticityStateVariable
variable_size = 48
groups = '0 12 24 48'
group_values = '50 51 52'
uo_state_var_evol_rate_comp_name = state_var_evol_rate_comp_voce
scale_factor = 1.0
[../]
[./state_var_evol_rate_comp_voce]
type = CrystalPlasticityStateVarRateComponentVoce
variable_size = 48
crystal_lattice_type = 'BCC'
groups = '0 12 24 48'
h0_group_values = '1 2 3'
tau0_group_values = '50 51 52'
tauSat_group_values = '70 81 92'
hardeningExponent_group_values = '1 2 3'
selfHardening_group_values ='4 5 6'
coplanarHardening_group_values='7 8 9'
GroupGroup_Hardening_group_values = '10 20 30
40 50 60
70 80 90'
uo_slip_rate_name = slip_rate_gss
uo_state_var_name = state_var_gss
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainUObasedCP
stol = 1e-2
tan_mod_type = exact
uo_slip_rates = 'slip_rate_gss'
uo_slip_resistances = 'slip_resistance_gss'
uo_state_vars = 'state_var_gss'
uo_state_var_evol_rate_comps = 'state_var_evol_rate_comp_voce'
[../]
[./strain]
type = ComputeFiniteStrain
displacements = 'disp_x disp_y'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
read_prop_user_object = prop_read
[../]
[]
[Postprocessors]
[./stress_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./e_yy]
type = ElementAverageValue
variable = e_yy
[../]
[./fp_yy]
type = ElementAverageValue
variable = fp_yy
[../]
[./gss]
type = ElementAverageValue
variable = gss
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.01
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
nl_abs_tol = 1e-10
nl_rel_step_tol = 1e-10
dtmax = 10.0
nl_rel_tol = 1e-10
end_time = 1
dtmin = 0.01
num_steps = 10
nl_abs_step_tol = 1e-10
[]
[Outputs]
exodus = true
[]
(modules/xfem/test/tests/moving_interface/moving_bimaterial_finite_strain_cut_mesh.i)
# This test is for two layer materials with different youngs modulus with AD
# The global stress is determined by switching the stress based on level set values
# The material interface is marked by a level set function
# The two layer materials are glued together
[GlobalParams]
displacements = 'disp_x disp_y'
[]
[XFEM]
output_cut_plane = true
[]
[UserObjects]
[cut]
type = InterfaceMeshCut2DUserObject
mesh_file = line.e
interface_velocity_function = -1
heal_always = true
[]
[]
[Mesh]
use_displaced_mesh = true
[generated_mesh]
type = GeneratedMeshGenerator
dim = 2
nx = 10
ny = 10
xmin = 0
xmax = 5
ymin = 0
ymax = 5
elem_type = QUAD4
[]
[left_bottom]
type = ExtraNodesetGenerator
new_boundary = 'left_bottom'
coord = '0 0'
input = generated_mesh
[]
[left_top]
type = ExtraNodesetGenerator
new_boundary = 'left_top'
coord = '0 5'
input = left_bottom
[]
[]
# [Functions]
# [ls_func]
# type = ParsedFunction
# value = 'y-2.73+t'
# []
# []
[Variables]
[disp_x]
[]
[disp_y]
[]
[]
[AuxVariables]
[ls]
[]
[a_strain_xx]
order = CONSTANT
family = MONOMIAL
[]
[a_strain_yy]
order = CONSTANT
family = MONOMIAL
[]
[a_strain_xy]
order = CONSTANT
family = MONOMIAL
[]
[b_strain_xx]
order = CONSTANT
family = MONOMIAL
[]
[b_strain_yy]
order = CONSTANT
family = MONOMIAL
[]
[b_strain_xy]
order = CONSTANT
family = MONOMIAL
[]
[stress_xx]
order = CONSTANT
family = MONOMIAL
[]
[stress_yy]
order = CONSTANT
family = MONOMIAL
[]
[stress_xy]
order = CONSTANT
family = MONOMIAL
[]
[]
[AuxKernels]
# [ls_function]
# type = FunctionAux
# variable = ls
# function = ls_func
# []
[a_strain_xx]
type = RankTwoAux
variable = a_strain_xx
rank_two_tensor = A_total_strain
index_i = 0
index_j = 0
[]
[a_strain_yy]
type = RankTwoAux
variable = a_strain_yy
rank_two_tensor = A_total_strain
index_i = 1
index_j = 1
[]
[a_strain_xy]
type = RankTwoAux
variable = a_strain_xy
rank_two_tensor = A_total_strain
index_i = 0
index_j = 1
[]
[b_strain_xx]
type = RankTwoAux
variable = b_strain_xx
rank_two_tensor = B_total_strain
index_i = 0
index_j = 0
[]
[b_strain_yy]
type = RankTwoAux
variable = b_strain_yy
rank_two_tensor = B_total_strain
index_i = 1
index_j = 1
[]
[b_strain_xy]
type = RankTwoAux
variable = b_strain_xy
rank_two_tensor = B_total_strain
index_i = 0
index_j = 1
[]
[stress_xx]
type = RankTwoAux
variable = stress_xx
rank_two_tensor = stress
index_i = 0
index_j = 0
[]
[stress_xy]
type = RankTwoAux
variable = stress_xy
rank_two_tensor = stress
index_i = 0
index_j = 1
[]
[stress_yy]
type = RankTwoAux
variable = stress_yy
rank_two_tensor = stress
index_i = 1
index_j = 1
[]
[]
[Kernels]
[solid_x]
type = StressDivergenceTensors
variable = disp_x
component = 0
use_displaced_mesh = true
[]
[solid_y]
type = StressDivergenceTensors
variable = disp_y
component = 1
use_displaced_mesh = true
[]
[]
[Constraints]
[dispx_constraint]
type = XFEMSingleVariableConstraint
use_displaced_mesh = false
variable = disp_x
alpha = 1e8
geometric_cut_userobject = 'level_set_cut_uo'
[]
[dispy_constraint]
type = XFEMSingleVariableConstraint
use_displaced_mesh = false
variable = disp_y
alpha = 1e8
geometric_cut_userobject = 'level_set_cut_uo'
[]
[]
[BCs]
[bottomx]
type = DirichletBC
boundary = bottom
variable = disp_x
value = 0.0
[]
[bottomy]
type = DirichletBC
boundary = bottom
variable = disp_y
value = 0.0
[]
[topx]
type = FunctionDirichletBC
boundary = top
variable = disp_x
function = 0.03*t
[]
[topy]
type = FunctionDirichletBC
boundary = top
variable = disp_y
function = '0.03*t'
[]
[]
[Materials]
[elasticity_tensor_A]
type = ComputeIsotropicElasticityTensor
base_name = A
youngs_modulus = 1e9
poissons_ratio = 0.3
[]
[strain_A]
type = ComputeFiniteStrain
base_name = A
[]
[stress_A]
type = ComputeFiniteStrainElasticStress
base_name = A
[]
[elasticity_tensor_B]
type = ComputeIsotropicElasticityTensor
base_name = B
youngs_modulus = 1e7
poissons_ratio = 0.3
[]
[strain_B]
type = ComputeFiniteStrain
base_name = B
[]
[stress_B]
type = ComputeFiniteStrainElasticStress
base_name = B
[]
[combined_stress]
type = LevelSetBiMaterialRankTwo
levelset_positive_base = 'A'
levelset_negative_base = 'B'
level_set_var = ls
prop_name = stress
[]
[combined_jacob_mult]
type = LevelSetBiMaterialRankFour
levelset_positive_base = 'A'
levelset_negative_base = 'B'
level_set_var = ls
prop_name = Jacobian_mult
[]
[]
[Postprocessors]
[disp_x_norm]
type = ElementL2Norm
variable = disp_x
[]
[disp_y_norm]
type = ElementL2Norm
variable = disp_y
[]
[]
[Executioner]
type = Transient
solve_type = NEWTON
petsc_options_iname = '-pc_type'
petsc_options_value = 'lu'
automatic_scaling = true
# controls for nonlinear iterations
nl_max_its = 15
nl_rel_tol = 1e-13
nl_abs_tol = 1e-50
# time control
start_time = 0.0
dt = 0.1
num_steps = 4
max_xfem_update = 1
[]
[Outputs]
print_linear_residuals = false
exodus = true
[]
(modules/tensor_mechanics/test/tests/isotropicSD_plasticity/isotropicSD.i)
# UserObject IsotropicSD test, with constant hardening.
# Linear strain is applied in the x and y direction.
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -.5
xmax = .5
ymin = -.5
ymax = .5
zmin = -.5
zmax = .5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./xdisp]
type = FunctionDirichletBC
variable = disp_x
boundary = 'right'
function = '0.005*t'
[../]
[./ydisp]
type = FunctionDirichletBC
variable = disp_y
boundary = 'top'
function = '0.005*t'
[../]
[./yfix]
type = DirichletBC
variable = disp_y
boundary = 'bottom'
value = 0
[../]
[./xfix]
type = DirichletBC
variable = disp_x
boundary = 'left'
value = 0
[../]
[./zfix]
type = DirichletBC
variable = disp_z
boundary = 'back'
value = 0
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./plastic_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./plastic_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./plastic_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./plastic_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./plastic_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./plastic_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[./intnl]
order = CONSTANT
family = MONOMIAL
[../]
[./sdev]
order = CONSTANT
family = MONOMIAL
[../]
[./sdet]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./plastic_xx]
type = RankTwoAux
rank_two_tensor = plastic_strain
variable = plastic_xx
index_i = 0
index_j = 0
[../]
[./plastic_xy]
type = RankTwoAux
rank_two_tensor = plastic_strain
variable = plastic_xy
index_i = 0
index_j = 1
[../]
[./plastic_xz]
type = RankTwoAux
rank_two_tensor = plastic_strain
variable = plastic_xz
index_i = 0
index_j = 2
[../]
[./plastic_yy]
type = RankTwoAux
rank_two_tensor = plastic_strain
variable = plastic_yy
index_i = 1
index_j = 1
[../]
[./plastic_yz]
type = RankTwoAux
rank_two_tensor = plastic_strain
variable = plastic_yz
index_i = 1
index_j = 2
[../]
[./plastic_zz]
type = RankTwoAux
rank_two_tensor = plastic_strain
variable = plastic_zz
index_i = 2
index_j = 2
[../]
[./f]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = f
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[./intnl]
type = MaterialStdVectorAux
index = 0
property = plastic_internal_parameter
variable = intnl
[../]
[./sdev]
type = RankTwoScalarAux
variable = sdev
rank_two_tensor = stress
scalar_type = VonMisesStress
[../]
[]
[Postprocessors]
[./sdev]
type = PointValue
point = '0 0 0'
variable = sdev
[../]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./p_xx]
type = PointValue
point = '0 0 0'
variable = plastic_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./p_xy]
type = PointValue
point = '0 0 0'
variable = plastic_xy
[../]
[./p_xz]
type = PointValue
point = '0 0 0'
variable = plastic_xz
[../]
[./p_yz]
type = PointValue
point = '0 0 0'
variable = plastic_yz
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./p_yy]
type = PointValue
point = '0 0 0'
variable = plastic_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./p_zz]
type = PointValue
point = '0 0 0'
variable = plastic_zz
[../]
[./intnl]
type = PointValue
point = '0 0 0'
variable = intnl
[../]
[]
[UserObjects]
[./str]
type = TensorMechanicsHardeningConstant
value = 300
[../]
[./IsotropicSD]
type = TensorMechanicsPlasticIsotropicSD
b = -0.2
c = -0.779422863
associative = true
yield_strength = str
yield_function_tolerance = 1e-5
internal_constraint_tolerance = 1e-9
use_custom_returnMap = false
use_custom_cto = false
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '121e3 80e3'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1e-9
plastic_models = IsotropicSD
debug_fspb = crash
tangent_operator = elastic
[../]
[]
[Executioner]
num_steps = 3
dt = .5
type = Transient
nl_rel_tol = 1e-6
nl_max_its = 10
l_tol = 1e-4
l_max_its = 50
solve_type = PJFNK
petsc_options_iname = '-pc_type'
petsc_options_value = 'lu'
[]
[Outputs]
perf_graph = false
csv = true
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
(modules/tensor_mechanics/test/tests/action/custom_output.i)
[GlobalParams]
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
[ring]
type = GeneratedMeshGenerator
dim = 3
[]
[]
[BCs]
[fix_x1]
type = DirichletBC
boundary = left
variable = disp_x
value = 0
[]
[fix_x2]
type = FunctionDirichletBC
boundary = right
variable = disp_x
function = 0.1*sin(t)
[]
[fix_y]
type = DirichletBC
boundary = 'left right'
variable = disp_y
value = 0
[]
[fix_z]
type = DirichletBC
boundary = 'left right'
variable = disp_z
value = 0
[]
[]
[Modules/TensorMechanics/Master]
[all]
add_variables = true
strain = FINITE
generate_output = 'vonmises_stress effective_alt_total_strain'
[]
[]
[Materials]
[stress]
type = ComputeFiniteStrainElasticStress
[]
[elastic]
type = ComputeIsotropicElasticityTensor
youngs_modulus = 0.3
shear_modulus = 100
[]
[alt_strain]
type = ComputeFiniteStrain
base_name = alt
[]
[]
[Executioner]
type = Transient
num_steps = 12
solve_type = PJFNK
[]
[Outputs]
exodus = true
print_linear_residuals = false
perf_graph = true
[]
(modules/contact/test/tests/mortar_aux_kernels/block-dynamics-aux-wear-vel.i)
starting_point = 0.5e-1
offset = -0.05
[GlobalParams]
displacements = 'disp_x disp_y'
[]
[Mesh]
file = long-bottom-block-1elem-blocks.e
[]
[Variables]
[disp_x]
block = '1 2'
[]
[disp_y]
block = '1 2'
[]
[normal_lm]
block = 3
use_dual = true
scaling = 1.0e3
[]
[frictional_lm]
block = 3
use_dual = true
[]
[]
[ICs]
[disp_y]
block = 2
variable = disp_y
value = '${fparse starting_point + offset}'
type = ConstantIC
[]
[]
[Kernels]
[DynamicTensorMechanics]
displacements = 'disp_x disp_y'
generate_output = 'stress_xx stress_yy'
strain = FINITE
block = '1 2'
zeta = 1.0
hht_alpha = 0.0
[]
[inertia_x]
type = InertialForce
variable = disp_x
velocity = vel_x
acceleration = accel_x
beta = 0.25
gamma = 0.5
alpha = 0
eta = 0.0
block = '1 2'
[]
[inertia_y]
type = InertialForce
variable = disp_y
velocity = vel_y
acceleration = accel_y
beta = 0.25
gamma = 0.5
alpha = 0
eta = 0.0
block = '1 2'
[]
[]
[Materials]
[elasticity_2]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[]
[elasticity_1]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e8
poissons_ratio = 0.3
[]
[stress]
type = ComputeFiniteStrainElasticStress
block = '1 2'
[]
[strain]
type = ComputeFiniteStrain
block = '1 2'
[]
[density]
type = GenericConstantMaterial
block = '1 2'
prop_names = 'density'
prop_values = '7750'
[]
[]
[AuxVariables]
[worn_depth]
block = '3'
[]
[gap_vel]
block = '3'
[]
[vel_x]
block = '1 2'
[]
[accel_x]
block = '1 2'
[]
[vel_y]
block = '1 2'
[]
[accel_y]
block = '1 2'
[]
[vel_z]
block = '1 2'
[]
[accel_z]
block = '1 2'
[]
[]
[AuxKernels]
[gap_vel]
type = WeightedGapVelAux
variable = gap_vel
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
disp_x = disp_x
disp_y = disp_y
[]
[worn_depth]
type = MortarArchardsLawAux
variable = worn_depth
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
displacements = 'disp_x disp_y'
friction_coefficient = 0.5
energy_wear_coefficient = 1.0
normal_pressure = normal_lm
[]
[accel_x]
type = NewmarkAccelAux
variable = accel_x
displacement = disp_x
velocity = vel_x
beta = 0.25
execute_on = 'linear timestep_end'
[]
[vel_x]
type = NewmarkVelAux
variable = vel_x
acceleration = accel_x
gamma = 0.5
execute_on = 'linear timestep_end'
[]
[accel_y]
type = NewmarkAccelAux
variable = accel_y
displacement = disp_y
velocity = vel_y
beta = 0.25
execute_on = 'linear timestep_end'
[]
[vel_y]
type = NewmarkVelAux
variable = vel_y
acceleration = accel_y
gamma = 0.5
execute_on = 'linear timestep_end'
[]
[]
[Constraints]
[weighted_gap_lm]
type = ComputeDynamicFrictionalForceLMMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = normal_lm
disp_x = disp_x
disp_y = disp_y
use_displaced_mesh = true
c = 1e4
c_t = 1e6
mu = 0.15
friction_lm = frictional_lm
interpolate_normals = false
capture_tolerance = 1.0e-5
newmark_beta = 0.25
newmark_gamma = 0.5
[]
[normal_x]
type = NormalMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = normal_lm
secondary_variable = disp_x
component = x
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[normal_y]
type = NormalMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = normal_lm
secondary_variable = disp_y
component = y
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[tangential_x]
type = TangentialMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = frictional_lm
secondary_variable = disp_x
component = x
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[tangential_y]
type = TangentialMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = frictional_lm
secondary_variable = disp_y
component = y
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[]
[BCs]
[botx]
type = DirichletBC
variable = disp_x
boundary = 40
value = 0.0
[]
[boty]
type = DirichletBC
variable = disp_y
boundary = 40
value = 0.0
[]
[topy]
type = FunctionDirichletBC
variable = disp_y
boundary = 30
function = '${starting_point} * cos(16.0 * pi / 4 * t) + ${offset}'
[]
[leftx]
type = FunctionDirichletBC
variable = disp_x
boundary = 50
function = '1e-2 * t'
[]
[]
[Executioner]
type = Transient
end_time = 0.3
dt = 0.03
dtmin = .002
solve_type = 'NEWTON'
petsc_options = '-snes_converged_reason -ksp_converged_reason -pc_svd_monitor '
'-snes_linesearch_monitor -snes_ksp_ew'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type -pc_factor_shift_type -pc_factor_shift_amount'
petsc_options_value = 'lu superlu_dist NONZERO 1e-15'
nl_max_its = 40
nl_abs_tol = 1.0e-11
nl_rel_tol = 1.0e-11
line_search = 'l2'
snesmf_reuse_base = true
[TimeIntegrator]
type = NewmarkBeta
beta = 0.25
gamma = 0.5
[]
[]
[Debug]
show_var_residual_norms = true
[]
[Outputs]
exodus = true
checkpoint = true
[]
[Preconditioning]
[smp]
type = SMP
full = true
[]
[]
[Postprocessors]
active = 'contact'
[num_nl]
type = NumNonlinearIterations
[]
[cumulative]
type = CumulativeValuePostprocessor
postprocessor = num_nl
[]
[contact]
type = ContactDOFSetSize
variable = normal_lm
subdomain = '3'
execute_on = 'nonlinear timestep_end'
[]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/uni_axial1.i)
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
# back = zmin
# front = zmax
# bottom = ymin
# top = ymax
# left = xmin
# right = xmax
[./xmin_xzero]
type = DirichletBC
variable = disp_x
boundary = 'left'
value = '0'
[../]
[./ymin_yzero]
type = DirichletBC
variable = disp_y
boundary = 'bottom'
value = '0'
[../]
[./zmin_zzero]
type = DirichletBC
variable = disp_z
boundary = 'back'
value = '0'
[../]
[./zmax_disp]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front'
function = '-1E-3*t'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./mc_int]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./mc_int_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_internal_parameter
variable = mc_int
[../]
[./yield_fcn_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./mc_int]
type = PointValue
point = '0 0 0'
variable = mc_int
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = yield_fcn
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 10E6
[../]
[./mc_phi]
type = TensorMechanicsHardeningExponential
value_0 = 0
value_residual = 0.6981317 # 40deg
rate = 10000
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 0
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 0
mc_edge_smoother = 25
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-10
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '5.77E10 3.85E10' # young = 100Gpa, poisson = 0.3
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-10
plastic_models = mc
max_NR_iterations = 1000
debug_fspb = crash
[../]
[]
[Preconditioning]
[./andy]
type = SMP
full = true
[../]
[]
[Executioner]
end_time = 0.5
dt = 0.05
solve_type = PJFNK # cannot use NEWTON because we are using ComputeFiniteStrain, and hence the Jacobian contributions will not be correct, even though ComputeMultiPlasticityStress will compute the correct consistent tangent operator for small strains
type = Transient
line_search = 'none'
nl_rel_tol = 1E-10
l_tol = 1E-3
l_max_its = 200
nl_max_its = 10
petsc_options_iname = '-pc_type -pc_asm_overlap -sub_pc_type -ksp_type -ksp_gmres_restart'
petsc_options_value = ' asm 2 lu gmres 200'
[]
[Outputs]
file_base = uni_axial1
exodus = true
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/stress_recovery/patch/patch_finite_stress.i)
[GlobalParams]
displacements = 'disp_x disp_y'
[]
[Mesh]
type = GeneratedMesh
dim = 2
nx = 2
ny = 2
elem_type = QUAD4
[]
[Variables]
[disp_x]
order = FIRST
family = LAGRANGE
[]
[disp_y]
order = FIRST
family = LAGRANGE
[]
[]
[AuxVariables]
[stress_xx]
order = FIRST
family = MONOMIAL
[]
[stress_yy]
order = FIRST
family = MONOMIAL
[]
[stress_xx_recovered]
order = FIRST
family = LAGRANGE
[]
[stress_yy_recovered]
order = FIRST
family = LAGRANGE
[]
[]
[AuxKernels]
[stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = 'timestep_end'
[]
[stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = 'timestep_end'
[]
[stress_xx_recovered]
type = NodalPatchRecoveryAux
variable = stress_xx_recovered
nodal_patch_recovery_uo = stress_xx_patch
execute_on = 'TIMESTEP_END'
[]
[stress_yy_recovered]
type = NodalPatchRecoveryAux
variable = stress_yy_recovered
nodal_patch_recovery_uo = stress_yy_patch
execute_on = 'TIMESTEP_END'
[]
[]
[Kernels]
[solid_x]
type = StressDivergenceTensors
variable = disp_x
component = 0
[]
[solid_y]
type = StressDivergenceTensors
variable = disp_y
component = 1
[]
[]
[Materials]
[strain]
type = ComputeFiniteStrain
[]
[Cijkl]
type = ComputeIsotropicElasticityTensor
poissons_ratio = 0.3
youngs_modulus = 2.1e+5
[]
[stress]
type = ComputeFiniteStrainElasticStress
[]
[]
[BCs]
[top_xdisp]
type = FunctionDirichletBC
variable = disp_x
boundary = 'top'
function = 0
[]
[top_ydisp]
type = FunctionDirichletBC
variable = disp_y
boundary = 'top'
function = t
[]
[bottom_xdisp]
type = FunctionDirichletBC
variable = disp_x
boundary = 'bottom'
function = 0
[]
[bottom_ydisp]
type = FunctionDirichletBC
variable = disp_y
boundary = 'bottom'
function = 0
[]
[]
[UserObjects]
[stress_xx_patch]
type = NodalPatchRecoveryMaterialProperty
patch_polynomial_order = FIRST
property = 'stress'
component = '0 0'
execute_on = 'TIMESTEP_END'
[]
[stress_yy_patch]
type = NodalPatchRecoveryMaterialProperty
patch_polynomial_order = FIRST
property = 'stress'
component = '1 1'
execute_on = 'TIMESTEP_END'
[]
[]
[Preconditioning]
[smp]
type = SMP
full = true
ksp_norm = default
[]
[]
[Executioner]
type = Transient
solve_type = NEWTON
petsc_options_iname = '-ksp_type -pc_type'
petsc_options_value = 'preonly lu'
nl_abs_tol = 1e-8
nl_rel_tol = 1e-8
l_max_its = 100
nl_max_its = 30
dt = 0.01
dtmin = 1e-11
start_time = 0
end_time = 0.05
[]
[Outputs]
exodus = true
print_linear_residuals = false
[]
(modules/tensor_mechanics/test/tests/hyperelastic_viscoplastic/one_elem.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'ux uy uz'
[]
[Variables]
[./ux]
block = 0
[../]
[./uy]
block = 0
[../]
[./uz]
block = 0
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'ux uy uz'
use_displaced_mesh = true
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./peeq]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./peeq]
type = MaterialRealAux
variable = peeq
property = ep_eqv
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = uy
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = ux
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = uz
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = uz
boundary = front
function = '0.01*t'
[../]
[]
[UserObjects]
[./flowstress]
type = HEVPRambergOsgoodHardening
yield_stress = 100
hardening_exponent = 0.1
reference_plastic_strain = 0.002
intvar_prop_name = ep_eqv
[../]
[./flowrate]
type = HEVPFlowRatePowerLawJ2
reference_flow_rate = 0.0001
flow_rate_exponent = 50.0
flow_rate_tol = 1
strength_prop_name = flowstress
[../]
[./ep_eqv]
type = HEVPEqvPlasticStrain
intvar_rate_prop_name = ep_eqv_rate
[../]
[./ep_eqv_rate]
type = HEVPEqvPlasticStrainRate
flow_rate_prop_name = flowrate
[../]
[]
[Materials]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'ux uy uz'
[../]
[./viscop]
type = FiniteStrainHyperElasticViscoPlastic
block = 0
resid_abs_tol = 1e-18
resid_rel_tol = 1e-8
maxiters = 50
max_substep_iteration = 5
flow_rate_user_objects = 'flowrate'
strength_user_objects = 'flowstress'
internal_var_user_objects = 'ep_eqv'
internal_var_rate_user_objects = 'ep_eqv_rate'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
C_ijkl = '2.8e5 1.2e5 1.2e5 2.8e5 1.2e5 2.8e5 0.8e5 0.8e5 0.8e5'
fill_method = symmetric9
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./peeq]
type = ElementAverageValue
variable = peeq
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.02
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
dtmax = 10.0
nl_rel_tol = 1e-10
dtmin = 0.02
num_steps = 10
[]
[Outputs]
file_base = one_elem
exodus = true
csv = false
[]
(modules/tensor_mechanics/test/tests/auxkernels/principalstress.i)
[Mesh]
type = GeneratedMesh
elem_type = HEX8
dim = 3
nx = 1
ny = 1
nz = 1
xmin=0.0
xmax=1.0
ymin=0.0
ymax=1.0
zmin=0.0
zmax=1.0
displacements = 'disp_x disp_y disp_z'
[]
[Variables]
[./disp_x]
order = FIRST
family = LAGRANGE
[../]
[./disp_y]
order = FIRST
family = LAGRANGE
[../]
[./disp_z]
order = FIRST
family = LAGRANGE
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[Materials]
[./fplastic]
type = FiniteStrainPlasticMaterial
block = 0
yield_stress='0. 445. 0.05 610. 0.1 680. 0.38 810. 0.95 920. 2. 950.'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
C_ijkl = '2.827e5 1.21e5 1.21e5 2.827e5 1.21e5 2.827e5 0.808e5 0.808e5 0.808e5'
fill_method = symmetric9
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./left]
type = DirichletBC
variable = disp_x
boundary = left
value = 0.0
[../]
[./bottom]
type = DirichletBC
variable = disp_y
boundary = bottom
value = 0.0
[../]
[./back]
type = DirichletBC
variable = disp_z
boundary = back
value = 0.0
[../]
[./front]
type = FunctionDirichletBC
variable = disp_z
boundary = front
function = 't'
[../]
[./right]
type = FunctionDirichletBC
variable = disp_y
boundary = right
function = '-0.5*t'
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_max]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_mid]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_min]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./stress_max]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = stress_max
scalar_type = MaxPrincipal
[../]
[./stress_mid]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = stress_mid
scalar_type = MidPrincipal
[../]
[./stress_min]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = stress_min
scalar_type = MinPrincipal
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./stress_max]
type = ElementAverageValue
variable = stress_max
[../]
[./stress_mid]
type = ElementAverageValue
variable = stress_mid
[../]
[./stress_min]
type = ElementAverageValue
variable = stress_min
[../]
[]
[Executioner]
type = Transient
dt=0.1
dtmin=0.1
dtmax=1
end_time=1.0
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
nl_rel_tol = 1e-10
nl_abs_tol = 1e-10
[]
[Outputs]
exodus = true
csv = true
[]
(modules/tensor_mechanics/test/tests/multi/rock1.i)
# Plasticity models:
# Mohr-Coulomb with cohesion = 40MPa, friction angle = 35deg, dilation angle = 10deg
# Tensile with strength = 1MPa
# WeakPlaneShear with cohesion = 1MPa, friction angle = 25deg, dilation angle = 25deg
# WeakPlaneTensile with strength = 0.01MPa
#
# Lame lambda = 1GPa. Lame mu = 1.3GPa
#
# A line of elements is perturbed randomly, and return to the yield surface at each quadpoint is checked
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1000
ny = 1234
nz = 1
xmin = 0
xmax = 1000
ymin = 0
ymax = 1234
zmin = 0
zmax = 1
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[ICs]
[./x]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_x
[../]
[./y]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_y
[../]
[./z]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_z
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./f3]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[./int3]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./f3]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 3
variable = f3
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[./int3]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 3
variable = int3
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./raw_f0]
type = ElementExtremeValue
variable = f0
outputs = console
[../]
[./raw_f1]
type = ElementExtremeValue
variable = f1
outputs = console
[../]
[./raw_f2]
type = ElementExtremeValue
variable = f2
outputs = console
[../]
[./raw_f3]
type = ElementExtremeValue
variable = f3
outputs = console
[../]
[./iter]
type = ElementExtremeValue
variable = iter
outputs = console
[../]
[./f0]
type = FunctionValuePostprocessor
function = should_be_zero0_fcn
[../]
[./f1]
type = FunctionValuePostprocessor
function = should_be_zero1_fcn
[../]
[./f2]
type = FunctionValuePostprocessor
function = should_be_zero2_fcn
[../]
[./f3]
type = FunctionValuePostprocessor
function = should_be_zero3_fcn
[../]
[]
[Functions]
[./should_be_zero0_fcn]
type = ParsedFunction
value = 'if(a<1E-1,0,a)'
vars = 'a'
vals = 'raw_f0'
[../]
[./should_be_zero1_fcn]
type = ParsedFunction
value = 'if(a<1E-1,0,a)'
vars = 'a'
vals = 'raw_f1'
[../]
[./should_be_zero2_fcn]
type = ParsedFunction
value = 'if(a<1E-1,0,a)'
vars = 'a'
vals = 'raw_f2'
[../]
[./should_be_zero3_fcn]
type = ParsedFunction
value = 'if(a<1E-1,0,a)'
vars = 'a'
vals = 'raw_f3'
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 4E7
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 35
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 10
convert_to_radians = true
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 4E6
yield_function_tolerance = 1.0E-1
internal_constraint_tolerance = 1.0E-7
[../]
[./ts]
type = TensorMechanicsHardeningConstant
value = 1E6
[../]
[./tensile]
type = TensorMechanicsPlasticTensile
tensile_strength = ts
tensile_tip_smoother = 1E5
yield_function_tolerance = 1.0E-1
internal_constraint_tolerance = 1.0E-7
[../]
[./coh]
type = TensorMechanicsHardeningConstant
value = 1E6
[../]
[./tanphi]
type = TensorMechanicsHardeningConstant
value = 0.46630766
[../]
[./tanpsi]
type = TensorMechanicsHardeningConstant
value = 0.46630766
[../]
[./wps]
type = TensorMechanicsPlasticWeakPlaneShear
cohesion = coh
tan_friction_angle = tanphi
tan_dilation_angle = tanpsi
smoother = 1E5
yield_function_tolerance = 1.0E-1
internal_constraint_tolerance = 1.0E-7
[../]
[./str]
type = TensorMechanicsHardeningConstant
value = 0.01E6
[../]
[./wpt]
type = TensorMechanicsPlasticWeakPlaneTensile
tensile_strength = str
yield_function_tolerance = 1.0E-1
internal_constraint_tolerance = 1.0E-7
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '1E9 1.3E9'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-7
plastic_models = 'mc tensile wps wpt'
deactivation_scheme = 'optimized_to_safe_to_dumb'
max_NR_iterations = 20
min_stepsize = 1E-4
max_stepsize_for_dumb = 1E-3
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1 1 1'
debug_jac_at_intnl = '1 1 1 1'
debug_stress_change = 1E1
debug_pm_change = '1E-6 1E-6 1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6 1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = rock1
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/planar3.i)
# apply repeated stretches in x z directions, and smaller stretches along the y direction,
# so that sigma_I = sigma_II,
# which means that lode angle = 30deg.
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '1E-6*x*t'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0.25E-6*y*sin(t)'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1.1E-6*z*t'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = f
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = f
[../]
[./iter]
type = PointValue
point = '0 0 0'
variable = iter
[../]
[]
[UserObjects]
[./coh]
type = TensorMechanicsHardeningConstant
value = 10
[../]
[./phi]
type = TensorMechanicsHardeningConstant
value = 0.9
[../]
[./psi]
type = TensorMechanicsHardeningConstant
value = 0.1
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulombMulti
cohesion = coh
friction_angle = phi
dilation_angle = psi
yield_function_tolerance = 1E-8
shift = 1E-8
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = mc
deactivation_scheme = safe
max_NR_iterations = 3
min_stepsize = 1
max_stepsize_for_dumb = 1
debug_fspb = crash
debug_jac_at_stress = '10 5 2 5 11 -1 2 -1 12'
debug_jac_at_pm = '1 1 1 1 1 1'
debug_jac_at_intnl = 1
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6 1E-6 1E-6 1E-6 1E-6'
debug_intnl_change = 1E-6
[../]
[]
[Executioner]
end_time = 10
dt = 1
type = Transient
[]
[Outputs]
file_base = planar3
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/contact/test/tests/pdass_problems/cylinder_friction.i)
[GlobalParams]
volumetric_locking_correction = true
displacements = 'disp_x disp_y'
[]
[Mesh]
[input_file]
type = FileMeshGenerator
file = hertz_cyl_coarser.e
[]
[secondary]
type = LowerDBlockFromSidesetGenerator
new_block_id = 10001
new_block_name = 'secondary_lower'
sidesets = '3'
input = input_file
[]
[primary]
type = LowerDBlockFromSidesetGenerator
new_block_id = 10000
sidesets = '2'
new_block_name = 'primary_lower'
input = secondary
[]
[]
[Problem]
type = ReferenceResidualProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[disp_x]
[]
[disp_y]
[]
[frictionless_normal_lm]
order = FIRST
family = LAGRANGE
block = 'secondary_lower'
use_dual = true
[]
[tangential_lm]
block = 'secondary_lower'
use_dual = true
[]
[]
[AuxVariables]
[stress_xx]
order = CONSTANT
family = MONOMIAL
[]
[stress_yy]
order = CONSTANT
family = MONOMIAL
[]
[stress_xy]
order = CONSTANT
family = MONOMIAL
[]
[saved_x]
[]
[saved_y]
[]
[diag_saved_x]
[]
[diag_saved_y]
[]
[]
[Functions]
[disp_ramp_vert]
type = PiecewiseLinear
x = '0. 1. 3.5'
y = '0. -0.020 -0.020'
[]
[disp_ramp_horz]
type = PiecewiseLinear
x = '0. 1. 3.5'
y = '0. 0.0 0.015'
[]
[]
[Kernels]
[TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y'
extra_vector_tags = 'ref'
block = '1 2 3 4 5 6 7'
[]
[]
[AuxKernels]
[stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
block = '1 2 3 4 5 6 7'
[]
[stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
block = '1 2 3 4 5 6 7'
[]
[stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
block = '1 2 3 4 5 6 7'
[]
[]
[Postprocessors]
[bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[]
[bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[]
[top_react_x]
type = NodalSum
variable = saved_x
boundary = 4
[]
[top_react_y]
type = NodalSum
variable = saved_y
boundary = 4
[]
[_dt]
type = TimestepSize
[]
[num_lin_it]
type = NumLinearIterations
[]
[num_nonlin_it]
type = NumNonlinearIterations
[]
[]
[BCs]
[side_x]
type = DirichletBC
variable = disp_y
boundary = '1 2'
value = 0.0
[]
[bot_y]
type = DirichletBC
variable = disp_x
boundary = '1 2'
value = 0.0
[]
[top_y_disp]
type = FunctionDirichletBC
variable = disp_y
boundary = 4
function = disp_ramp_vert
[]
[top_x_disp]
type = FunctionDirichletBC
variable = disp_x
boundary = 4
function = disp_ramp_horz
[]
[]
[Materials]
[stuff1_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e10
poissons_ratio = 0.0
[]
[stuff1_strain]
type = ComputeFiniteStrain
block = '1'
[]
[stuff1_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[]
[stuff2_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2 3 4 5 6 7'
youngs_modulus = 1e6
poissons_ratio = 0.3
[]
[stuff2_strain]
type = ComputeFiniteStrain
block = '2 3 4 5 6 7'
[]
[stuff2_stress]
type = ComputeFiniteStrainElasticStress
block = '2 3 4 5 6 7'
[]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options = '-snes_ksp_ew'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type -pc_factor_shift_type -pc_factor_shift_amount -mat_mffd_err'
petsc_options_value = 'lu superlu_dist NONZERO 1e-15 1e-5'
line_search = 'none'
nl_abs_tol = 1e-7
start_time = 0.0
end_time = 0.3 # 3.5
l_tol = 1e-4
dt = 0.1
dtmin = 0.001
[]
[Preconditioning]
[SMP]
type = SMP
full = true
[]
[]
[VectorPostprocessors]
[x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '3 4'
sort_by = id
[]
[y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '3 4'
sort_by = id
[]
[cont_press]
type = NodalValueSampler
variable = frictionless_normal_lm
boundary = '3'
sort_by = id
[]
[friction]
type = NodalValueSampler
variable = frictionless_normal_lm
boundary = '3'
sort_by = id
[]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
exodus = false
csv = false
[console]
type = Console
max_rows = 5
[]
[chkfile]
type = CSV
show = 'x_disp y_disp cont_press friction'
file_base = cylinder_friction_check
create_final_symlink = true
execute_on = 'FINAL'
[]
[]
[Constraints]
[weighted_gap_lm]
type = ComputeFrictionalForceLMMechanicalContact
primary_boundary = 2
secondary_boundary = 3
primary_subdomain = 10000
secondary_subdomain = 10001
variable = frictionless_normal_lm
disp_x = disp_x
disp_y = disp_y
use_displaced_mesh = true
friction_lm = tangential_lm
mu = 0.4
c_t = 1.0e5
c = 1.0e6
[]
[x]
type = NormalMortarMechanicalContact
primary_boundary = '2'
secondary_boundary = '3'
primary_subdomain = '10000'
secondary_subdomain = '10001'
variable = frictionless_normal_lm
secondary_variable = disp_x
component = x
use_displaced_mesh = true
compute_lm_residuals = false
[]
[y]
type = NormalMortarMechanicalContact
primary_boundary = '2'
secondary_boundary = '3'
primary_subdomain = '10000'
secondary_subdomain = '10001'
variable = frictionless_normal_lm
secondary_variable = disp_y
component = y
use_displaced_mesh = true
compute_lm_residuals = false
[]
[tangential_x]
type = TangentialMortarMechanicalContact
primary_boundary = 2
secondary_boundary = 3
primary_subdomain = 10000
secondary_subdomain = 10001
variable = tangential_lm
secondary_variable = disp_x
component = x
use_displaced_mesh = true
compute_lm_residuals = false
[]
[tangential_y]
type = TangentialMortarMechanicalContact
primary_boundary = 2
secondary_boundary = 3
primary_subdomain = 10000
secondary_subdomain = 10001
variable = tangential_lm
secondary_variable = disp_y
component = y
use_displaced_mesh = true
compute_lm_residuals = false
[]
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/user_object.i)
[Mesh]
type = GeneratedMesh
dim = 2
elem_type = QUAD4
displacements = 'disp_x disp_y'
nx = 2
ny = 2
[]
[GlobalParams]
volumetric_locking_correction = true
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y'
use_displaced_mesh = true
[../]
[]
[AuxVariables]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./e_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./fp_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./rotout]
order = CONSTANT
family = MONOMIAL
[../]
[./gss]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[UserObjects]
[./prop_read]
type = PropertyReadFile
prop_file_name = 'euler_ang_file.txt'
# Enter file data as prop#1, prop#2, .., prop#nprop
nprop = 3
read_type = element
[../]
[]
[AuxKernels]
[./stress_yy]
type = RankTwoAux
variable = stress_yy
rank_two_tensor = stress
index_j = 1
index_i = 1
execute_on = timestep_end
[../]
[./e_yy]
type = RankTwoAux
variable = e_yy
rank_two_tensor = lage
index_j = 1
index_i = 1
execute_on = timestep_end
[../]
[./fp_yy]
type = RankTwoAux
variable = fp_yy
rank_two_tensor = fp
index_j = 1
index_i = 1
execute_on = timestep_end
[../]
[./gss]
type = MaterialStdVectorAux
variable = gss
property = state_var_gss
index = 0
execute_on = timestep_end
[../]
[]
[BCs]
[./fix_x]
type = DirichletBC
variable = disp_x
boundary = 'left'
value = 0
[../]
[./fix_y]
type = DirichletBC
variable = disp_y
boundary = 'bottom'
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_y
boundary = top
function = tdisp
[../]
[]
[UserObjects]
[./slip_rate_gss]
type = CrystalPlasticitySlipRateGSS
variable_size = 12
slip_sys_file_name = input_slip_sys.txt
num_slip_sys_flowrate_props = 2
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
uo_state_var_name = state_var_gss
[../]
[./slip_resistance_gss]
type = CrystalPlasticitySlipResistanceGSS
variable_size = 12
uo_state_var_name = state_var_gss
[../]
[./state_var_gss]
type = CrystalPlasticityStateVariable
variable_size = 12
groups = '0 4 8 12'
group_values = '60.8 60.8 60.8'
uo_state_var_evol_rate_comp_name = state_var_evol_rate_comp_gss
scale_factor = 1.0
[../]
[./state_var_evol_rate_comp_gss]
type = CrystalPlasticityStateVarRateComponentGSS
variable_size = 12
hprops = '1.0 541.5 109.8 2.5'
uo_slip_rate_name = slip_rate_gss
uo_state_var_name = state_var_gss
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainUObasedCP
stol = 1e-2
tan_mod_type = exact
uo_slip_rates = 'slip_rate_gss'
uo_slip_resistances = 'slip_resistance_gss'
uo_state_vars = 'state_var_gss'
uo_state_var_evol_rate_comps = 'state_var_evol_rate_comp_gss'
[../]
[./strain]
type = ComputeFiniteStrain
displacements = 'disp_x disp_y'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
read_prop_user_object = prop_read
[../]
[]
[Postprocessors]
[./stress_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./e_yy]
type = ElementAverageValue
variable = e_yy
[../]
[./fp_yy]
type = ElementAverageValue
variable = fp_yy
[../]
[./gss]
type = ElementAverageValue
variable = gss
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.01
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
nl_abs_tol = 1e-10
nl_rel_step_tol = 1e-10
dtmax = 10.0
nl_rel_tol = 1e-10
end_time = 1
dtmin = 0.01
num_steps = 10
nl_abs_step_tol = 1e-10
[]
[Outputs]
exodus = true
[]
(modules/tensor_mechanics/test/tests/multi/three_surface06.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 1.5
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 1.1E-6m in y direction and 1.0E-6 in z direction.
# trial stress_yy = 1.1 and stress_zz = 1.0
#
# Then SimpleTester1 and SimpleTester2 should activate and the algorithm will return to
# the corner stress_yy=1.0, stress_zz=0.5
# However, this will mean internal1 < 0, so SimpleTester1 will be deactivated and
# then the algorithm will return to
# stress_yy=0.8, stress_zz=0.7
# internal1 should be 0.0, and internal2 should be 0.3
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1.1E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1.0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 1.5
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface06
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/xfem/test/tests/moving_interface/moving_bimaterial_finite_strain_esm.i)
# This test is for two layer materials with different youngs modulus with AD
# The global stress is determined by switching the stress based on level set values
# The material interface is marked by a level set function
# The two layer materials are glued together
[GlobalParams]
displacements = 'disp_x disp_y'
[]
[XFEM]
output_cut_plane = true
[]
[UserObjects]
[level_set_cut_uo]
type = LevelSetCutUserObject
level_set_var = ls
heal_always = true
[]
[esm]
type = CutElementSubdomainModifier
geometric_cut_userobject = level_set_cut_uo
apply_initial_conditions = false
[]
[]
[Mesh]
use_displaced_mesh = true
[generated_mesh]
type = GeneratedMeshGenerator
dim = 2
nx = 10
ny = 10
xmin = 0
xmax = 5
ymin = 0
ymax = 5
elem_type = QUAD4
[]
[bottom]
type = SubdomainBoundingBoxGenerator
input = generated_mesh
block_id = 0
bottom_left = '0 0 0'
top_right = '5 2.5 0'
[]
[top]
type = SubdomainBoundingBoxGenerator
input = bottom
block_id = 1
bottom_left = '0 2.5 0'
top_right = '5 5 0'
[]
[]
[Functions]
[ls_func]
type = ParsedFunction
value = 'y-2.73+t'
[]
[]
[Variables]
[disp_x]
[]
[disp_y]
[]
[]
[AuxVariables]
[ls]
[]
[strain_xx]
order = CONSTANT
family = MONOMIAL
[]
[strain_yy]
order = CONSTANT
family = MONOMIAL
[]
[strain_xy]
order = CONSTANT
family = MONOMIAL
[]
[stress_xx]
order = CONSTANT
family = MONOMIAL
[]
[stress_yy]
order = CONSTANT
family = MONOMIAL
[]
[stress_xy]
order = CONSTANT
family = MONOMIAL
[]
[]
[AuxKernels]
[ls_function]
type = FunctionAux
variable = ls
function = ls_func
[]
[strain_xx]
type = RankTwoAux
variable = strain_xx
rank_two_tensor = total_strain
index_i = 0
index_j = 0
[]
[strain_yy]
type = RankTwoAux
variable = strain_yy
rank_two_tensor = total_strain
index_i = 1
index_j = 1
[]
[strain_xy]
type = RankTwoAux
variable = strain_xy
rank_two_tensor = total_strain
index_i = 0
index_j = 1
[]
[stress_xx]
type = RankTwoAux
variable = stress_xx
rank_two_tensor = stress
index_i = 0
index_j = 0
[]
[stress_xy]
type = RankTwoAux
variable = stress_xy
rank_two_tensor = stress
index_i = 0
index_j = 1
[]
[stress_yy]
type = RankTwoAux
variable = stress_yy
rank_two_tensor = stress
index_i = 1
index_j = 1
[]
[]
[Kernels]
[solid_x]
type = StressDivergenceTensors
variable = disp_x
component = 0
use_displaced_mesh = true
[]
[solid_y]
type = StressDivergenceTensors
variable = disp_y
component = 1
use_displaced_mesh = true
[]
[]
[Constraints]
[dispx_constraint]
type = XFEMSingleVariableConstraint
use_displaced_mesh = false
variable = disp_x
alpha = 1e8
geometric_cut_userobject = 'level_set_cut_uo'
[]
[dispy_constraint]
type = XFEMSingleVariableConstraint
use_displaced_mesh = false
variable = disp_y
alpha = 1e8
geometric_cut_userobject = 'level_set_cut_uo'
[]
[]
[BCs]
[bottomx]
type = DirichletBC
boundary = bottom
variable = disp_x
value = 0.0
[]
[bottomy]
type = DirichletBC
boundary = bottom
variable = disp_y
value = 0.0
[]
[topx]
type = FunctionDirichletBC
boundary = top
variable = disp_x
function = 0.03*t
[]
[topy]
type = FunctionDirichletBC
boundary = top
variable = disp_y
function = '0.03*t'
[]
[]
[Materials]
[elasticity_tensor_A]
type = ComputeIsotropicElasticityTensor
block = 1
youngs_modulus = 1e9
poissons_ratio = 0.3
[]
[strain_A]
type = ComputeFiniteStrain
block = 1
[]
[stress_A]
type = ComputeFiniteStrainElasticStress
block = 1
[]
[elasticity_tensor_B]
type = ComputeIsotropicElasticityTensor
block = 0
youngs_modulus = 1e7
poissons_ratio = 0.3
[]
[strain_B]
type = ComputeFiniteStrain
block = 0
[]
[stress_B]
type = ComputeFiniteStrainElasticStress
block = 0
[]
[]
[Postprocessors]
[disp_x_norm]
type = ElementL2Norm
variable = disp_x
[]
[disp_y_norm]
type = ElementL2Norm
variable = disp_y
[]
[]
[Executioner]
type = Transient
solve_type = NEWTON
petsc_options_iname = '-pc_type'
petsc_options_value = 'lu'
automatic_scaling = true
# controls for nonlinear iterations
nl_max_its = 15
nl_rel_tol = 1e-13
nl_abs_tol = 1e-50
# time control
start_time = 0.0
dt = 0.1
num_steps = 4
max_xfem_update = 1
[]
[Outputs]
print_linear_residuals = false
exodus = true
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/random.i)
# apply many random large deformations, checking that the algorithm returns correctly to
# the yield surface each time.
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1000
ny = 125
nz = 1
xmin = 0
xmax = 1000
ymin = 0
ymax = 125
zmin = 0
zmax = 1
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[ICs]
[./x]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_x
[../]
[./y]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_y
[../]
[./z]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_z
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0'
[../]
[]
[AuxVariables]
[./yield_fcn]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./yield_fcn_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./yield_fcn_at_zero]
type = PointValue
point = '0 0 0'
variable = yield_fcn
outputs = 'console'
[../]
[./should_be_zero]
type = FunctionValuePostprocessor
function = should_be_zero_fcn
[../]
[./av_iter]
type = ElementAverageValue
variable = iter
outputs = 'console'
[../]
[]
[Functions]
[./should_be_zero_fcn]
type = ParsedFunction
value = 'if(a<1E-3,0,a)'
vars = 'a'
vals = 'yield_fcn_at_zero'
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 1E3
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 30
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 5
convert_to_radians = true
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 0.1E3
mc_edge_smoother = 25
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-6
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0.7E7 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
max_NR_iterations = 1000
ep_plastic_tolerance = 1E-6
min_stepsize = 1E-3
plastic_models = mc
debug_fspb = crash
deactivation_scheme = safe
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = random
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/contact/test/tests/verification/patch_tests/brick_4/brick4_template1.i)
[GlobalParams]
order = SECOND
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
file = brick4_mesh.e
[]
[Problem]
type = ReferenceResidualProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./penetration]
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./saved_z]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./diag_saved_z]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./inc_slip_z]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./accum_slip_z]
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y saved_z'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 4
paired_boundary = 3
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./ref_resid_x]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_x
[../]
[./ref_resid_y]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_y
[../]
[./sigma_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./sigma_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./disp_x59]
type = NodalVariableValue
nodeid = 58
variable = disp_x
[../]
[./disp_x64]
type = NodalVariableValue
nodeid = 63
variable = disp_x
[../]
[./disp_y59]
type = NodalVariableValue
nodeid = 58
variable = disp_y
[../]
[./disp_y64]
type = NodalVariableValue
nodeid = 63
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./bot_y]
type = DirichletBC
variable = disp_y
boundary = 1
value = 0.0
[../]
[./side_x]
type = DirichletBC
variable = disp_x
boundary = 2
value = 0.0
[../]
[./back_z]
type = DirichletBC
variable = disp_z
boundary = 6
value = 0.0
[../]
[./top_press]
type = Pressure
variable = disp_y
boundary = 5
factor = 109.89
[../]
[]
[Materials]
[./bot_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./bot_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./bot_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./top_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./top_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./top_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-7
nl_rel_tol = 1e-6
l_max_its = 50
nl_max_its = 100
dt = 1.0
end_time = 1.0
num_steps = 10
dtmin = 1.0
l_tol = 1e-4
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '1 3 4 5'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '1 3 4 5'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
show = 'bot_react_x bot_react_y disp_x59 disp_y59 disp_x64 disp_y64 stress_yy stress_zz top_react_x top_react_y x_disp y_disp cont_press'
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./leftright]
secondary = 3
primary = 4
normalize_penalty = true
tangential_tolerance = 1e-3
penalty = 1e+9
[../]
[]
(modules/tensor_mechanics/test/tests/initial_stress/mc_tensile.i)
# In this example, an initial stress is applied that
# is inadmissible, and the return-map algorithm must be
# used to return to the yield surface before any other
# computations can be carried out.
# In this case, the return-map algorithm must subdivide
# the initial stress, otherwise it does not converge.
# This test is testing that subdivision process.
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./bottomx]
type = DirichletBC
variable = disp_x
boundary = 'back'
value = 0.0
[../]
[./bottomy]
type = DirichletBC
variable = disp_y
boundary = 'back'
value = 0.0
[../]
[./bottomz]
type = DirichletBC
variable = disp_z
boundary = 'back'
value = 0.0
[../]
[./topx]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front'
function = '2*t-1'
[../]
[./topy]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front'
function = 't-1'
[../]
[./topz]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front'
function = 't-1'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./iter]
type = PointValue
point = '0 0 0'
variable = iter
outputs = console
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 1E5
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 60
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 5
convert_to_radians = true
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 4.0
mc_edge_smoother = 25
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-9
[../]
[./str]
type = TensorMechanicsHardeningConstant
value = 1
[../]
[./pt]
type = TensorMechanicsPlasticTensile
tensile_strength = str
yield_function_tolerance = 1E-3
tensile_tip_smoother = 0.05
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
displacements = 'disp_x disp_y disp_z'
eigenstrain_names = ini_stress
[../]
[./ini_stress]
type = ComputeEigenstrainFromInitialStress
initial_stress = '8E6 4E6 -18E6 4E6 -40E6 -2E6 -18E6 -2E6 -34E6'
eigenstrain_name = ini_stress
[../]
[./mc]
type = ComputeMultiPlasticityStress
ep_plastic_tolerance = 1E-9
plastic_models = 'pt mc'
deactivation_scheme = safe
max_NR_iterations = 100
min_stepsize = 0.1
[../]
[]
[Executioner]
end_time = 2
dt = 1
type = Transient
[]
[Outputs]
file_base = mc_tensile
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/hyperelastic_viscoplastic/one_elem_base.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'ux uy uz'
[]
[Variables]
[./ux]
block = 0
[../]
[./uy]
block = 0
[../]
[./uz]
block = 0
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'ux uy uz'
use_displaced_mesh = true
base_name = test
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./peeq]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = test_stress
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = test_fp
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./peeq]
type = MaterialRealAux
variable = peeq
property = ep_eqv
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = uy
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = ux
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = uz
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = uz
boundary = front
function = '0.01*t'
[../]
[]
[UserObjects]
[./flowstress]
type = HEVPRambergOsgoodHardening
yield_stress = 100
hardening_exponent = 0.1
reference_plastic_strain = 0.002
intvar_prop_name = ep_eqv
[../]
[./flowrate]
type = HEVPFlowRatePowerLawJ2
reference_flow_rate = 0.0001
flow_rate_exponent = 50.0
flow_rate_tol = 1
strength_prop_name = flowstress
base_name = test
[../]
[./ep_eqv]
type = HEVPEqvPlasticStrain
intvar_rate_prop_name = ep_eqv_rate
[../]
[./ep_eqv_rate]
type = HEVPEqvPlasticStrainRate
flow_rate_prop_name = flowrate
[../]
[]
[Materials]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'ux uy uz'
base_name = test
[../]
[./viscop]
type = FiniteStrainHyperElasticViscoPlastic
block = 0
resid_abs_tol = 1e-18
resid_rel_tol = 1e-8
maxiters = 50
max_substep_iteration = 5
flow_rate_user_objects = 'flowrate'
strength_user_objects = 'flowstress'
internal_var_user_objects = 'ep_eqv'
internal_var_rate_user_objects = 'ep_eqv_rate'
base_name = test
[../]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
C_ijkl = '2.8e5 1.2e5 1.2e5 2.8e5 1.2e5 2.8e5 0.8e5 0.8e5 0.8e5'
fill_method = symmetric9
base_name = test
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./peeq]
type = ElementAverageValue
variable = peeq
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.02
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
dtmax = 10.0
nl_rel_tol = 1e-10
dtmin = 0.02
num_steps = 10
[]
[Outputs]
file_base = one_elem_base
exodus = true
csv = false
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/crysp_linesearch.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'ux uy uz'
[]
[Variables]
[./ux]
block = 0
[../]
[./uy]
block = 0
[../]
[./uz]
block = 0
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./e_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./gss1]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'ux uy uz'
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./e_zz]
type = RankTwoAux
variable = e_zz
rank_two_tensor = lage
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./gss1]
type = MaterialStdVectorAux
variable = gss1
property = gss
index = 0
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = uy
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = ux
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = uz
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = uz
boundary = front
function = tdisp
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainCrystalPlasticity
block = 0
rtol = 1e-6
abs_tol = 1e-8
gtol = 1e-2
slip_sys_file_name = input_slip_sys.txt
nss = 12
num_slip_sys_flowrate_props = 2 #Number of properties in a slip system
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
hprops = '1.0 541.5 60.8 109.8 2.5'
gprops = '1 4 60.8 5 8 60.8 9 12 60.8'
tan_mod_type = exact
use_line_search = true
min_line_search_step_size = 0.01
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
block = 0
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'ux uy uz'
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./e_zz]
type = ElementAverageValue
variable = e_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./gss1]
type = ElementAverageValue
variable = gss1
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type'
petsc_options_value = 'lu'
nl_rel_tol = 1e-10
nl_abs_tol = 1e-10
dt = 0.025
dtmax = 10.0
dtmin = 0.02
num_steps = 10
[]
[Outputs]
file_base = crysp_lsearch_out
exodus = true
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/except2.i)
# checking for exception error messages
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '1E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 10
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 30
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 5
convert_to_radians = true
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 1
mc_edge_smoother = 25
mc_lode_cutoff = -1.0E-6
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = mc
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = 1
debug_jac_at_intnl = 1
debug_stress_change = 1E-5
debug_pm_change = 1E-6
debug_intnl_change = 1E-6
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = except2
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/combined/test/tests/cavity_pressure/additional_volume.i)
#
# Cavity Pressure Test
#
# This test is designed to compute an internal pressure based on
# p = n * R * / (V_cavity / T_cavity + V_add / T_add)
# where
# p is the pressure
# n is the amount of material in the volume (moles)
# R is the universal gas constant
# T_cavity is the temperature in the cavity
# T_add is the temperature of the additional volume
#
# The mesh is composed of one block (1) with an interior cavity of volume 8.
# Block 2 sits in the cavity and has a volume of 1. Thus, the total
# initial volume is 7. An additional volume of 2 is added.
#
# The test adjusts n, T, and V in the following way:
# n => n0 + alpha * t
# T => T0 + beta * t
# V => V_cavity0 + gamma * t + V_add
# with
# alpha = n0
# beta = T0 / 2
# gamma = -(0.003322259...) * V0
# T0 = 240.54443866068704
# V_cavity0 = 7
# V_add = 2
# T_add = 100
# n0 = f(p0)
# p0 = 100
# R = 8.314472 J * K^(-1) * mol^(-1)
#
# An additional volume of 2 with a temperature of 100.0 is included.
#
# So, n0 = p0 * (V_cavity / T_cavity + V_add / T_add) / R
# = 100 * (7 / 240.544439 + 2 / 100) / 8.314472
# = 0.59054
#
# The parameters combined at t = 1 gives p = 249.647.
#
# This test sets the initial temperature to 500, but the CavityPressure
# is told that that initial temperature is T0. Thus, the final solution
# is unchanged.
[GlobalParams]
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
file = 3d.e
[]
[GlobalParams]
volumetric_locking_correction = true
[]
[Functions]
[./displ_positive]
type = PiecewiseLinear
x = '0 1'
y = '0 0.0029069767441859684'
[../]
[./displ_negative]
type = PiecewiseLinear
x = '0 1'
y = '0 -0.0029069767441859684'
[../]
[./temp1]
type = PiecewiseLinear
x = '0 1'
y = '1 1.5'
scale_factor = 240.54443866068704
[../]
[./material_input_function]
type = PiecewiseLinear
x = '0 1'
y = '0 0.59054'
[../]
[./additional_volume]
type = ConstantFunction
value = 2
[../]
[./temperature_of_additional_volume]
type = ConstantFunction
value = 100
[../]
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[./temp]
initial_condition = 500
[../]
[./material_input]
[../]
[]
[AuxVariables]
[./pressure_residual_x]
[../]
[./pressure_residual_y]
[../]
[./pressure_residual_z]
[../]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zx]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
[../]
[./heat]
type = Diffusion
variable = temp
use_displaced_mesh = true
[../]
[./material_input_dummy]
type = Diffusion
variable = material_input
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
index_i = 0
index_j = 0
variable = stress_xx
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
index_i = 1
index_j = 1
variable = stress_yy
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
index_i = 2
index_j = 2
variable = stress_zz
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
index_i = 0
index_j = 1
variable = stress_xy
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
index_i = 1
index_j = 2
variable = stress_yz
[../]
[./stress_zx]
type = RankTwoAux
rank_two_tensor = stress
index_i = 2
index_j = 0
variable = stress_zx
[../]
[]
[BCs]
[./no_x_exterior]
type = DirichletBC
variable = disp_x
boundary = '7 8'
value = 0.0
[../]
[./no_y_exterior]
type = DirichletBC
variable = disp_y
boundary = '9 10'
value = 0.0
[../]
[./no_z_exterior]
type = DirichletBC
variable = disp_z
boundary = '11 12'
value = 0.0
[../]
[./prescribed_left]
type = FunctionDirichletBC
variable = disp_x
boundary = 13
function = displ_positive
[../]
[./prescribed_right]
type = FunctionDirichletBC
variable = disp_x
boundary = 14
function = displ_negative
[../]
[./no_y]
type = DirichletBC
variable = disp_y
boundary = '15 16'
value = 0.0
[../]
[./no_z]
type = DirichletBC
variable = disp_z
boundary = '17 18'
value = 0.0
[../]
[./no_x_interior]
type = DirichletBC
variable = disp_x
boundary = '1 2'
value = 0.0
[../]
[./no_y_interior]
type = DirichletBC
variable = disp_y
boundary = '3 4'
value = 0.0
[../]
[./no_z_interior]
type = DirichletBC
variable = disp_z
boundary = '5 6'
value = 0.0
[../]
[./temperatureInterior]
type = FunctionDirichletBC
boundary = 100
function = temp1
variable = temp
[../]
[./MaterialInput]
type = FunctionDirichletBC
boundary = '100 13 14 15 16'
function = material_input_function
variable = material_input
[../]
[./CavityPressure]
[./1]
boundary = 100
initial_pressure = 100
material_input = materialInput
R = 8.314472
temperature = aveTempInterior
initial_temperature = 240.54443866068704
volume = internalVolume
startup_time = 0.5
output = ppress
save_in = 'pressure_residual_x pressure_residual_y pressure_residual_z'
additional_volumes = volume1
temperature_of_additional_volumes = temperature1
[../]
[../]
[]
[Materials]
[./elast_tensor1]
type = ComputeElasticityTensor
C_ijkl = '0 5'
fill_method = symmetric_isotropic
block = 1
[../]
[./strain1]
type = ComputeFiniteStrain
block = 1
[../]
[./stress1]
type = ComputeFiniteStrainElasticStress
block = 1
[../]
[./elast_tensor2]
type = ComputeElasticityTensor
C_ijkl = '0 5'
fill_method = symmetric_isotropic
block = 2
[../]
[./strain2]
type = ComputeFiniteStrain
block = 2
[../]
[./stress2]
type = ComputeFiniteStrainElasticStress
block = 2
[../]
[]
[Executioner]
type = Transient
petsc_options_iname = '-pc_type -sub_pc_type'
petsc_options_value = 'asm lu'
nl_rel_tol = 1e-12
l_tol = 1e-12
l_max_its = 20
dt = 0.5
end_time = 1.0
snesmf_reuse_base = false
[]
[Postprocessors]
[./internalVolume]
type = InternalVolume
boundary = 100
execute_on = 'initial linear'
[../]
[./aveTempInterior]
type = SideAverageValue
boundary = 100
variable = temp
execute_on = 'initial linear'
[../]
[./materialInput]
type = SideAverageValue
boundary = '7 8 9 10 11 12'
variable = material_input
execute_on = linear
[../]
[./volume1]
type = FunctionValuePostprocessor
function = additional_volume
execute_on = 'initial linear'
[../]
[./temperature1]
type = FunctionValuePostprocessor
function = temperature_of_additional_volume
execute_on = 'initial linear'
[../]
[]
[Outputs]
exodus = true
[]
(modules/contact/test/tests/mortar_aux_kernels/block-dynamics-aux-wear.i)
starting_point = 0.5e-1
offset = -0.05
[GlobalParams]
displacements = 'disp_x disp_y'
[]
[Mesh]
file = long-bottom-block-1elem-blocks.e
[]
[Variables]
[disp_x]
block = '1 2'
[]
[disp_y]
block = '1 2'
[]
[normal_lm]
block = 3
use_dual = true
[]
[]
[ICs]
[disp_y]
block = 2
variable = disp_y
value = '${fparse starting_point + offset}'
type = ConstantIC
[]
[]
[Kernels]
[DynamicTensorMechanics]
displacements = 'disp_x disp_y'
generate_output = 'stress_xx stress_yy'
strain = FINITE
block = '1 2'
zeta = 1.0
hht_alpha = 0.0
[]
[inertia_x]
type = InertialForce
variable = disp_x
velocity = vel_x
acceleration = accel_x
beta = 0.25
gamma = 0.5
alpha = 0
eta = 0.0
block = '1 2'
[]
[inertia_y]
type = InertialForce
variable = disp_y
velocity = vel_y
acceleration = accel_y
beta = 0.25
gamma = 0.5
alpha = 0
eta = 0.0
block = '1 2'
[]
[]
[Materials]
[elasticity_2]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[]
[elasticity_1]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e8
poissons_ratio = 0.3
[]
[stress]
type = ComputeFiniteStrainElasticStress
block = '1 2'
[]
[strain]
type = ComputeFiniteStrain
block = '1 2'
[]
[density]
type = GenericConstantMaterial
block = '1 2'
prop_names = 'density'
prop_values = '7750'
[]
[]
[AuxVariables]
[worn_depth]
block = '3'
[]
[vel_x]
block = '1 2'
[]
[accel_x]
block = '1 2'
[]
[vel_y]
block = '1 2'
[]
[accel_y]
block = '1 2'
[]
[vel_z]
block = '1 2'
[]
[accel_z]
block = '1 2'
[]
[]
[AuxKernels]
[worn_depth]
type = MortarArchardsLawAux
variable = worn_depth
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
displacements = 'disp_x disp_y'
friction_coefficient = 0.5
energy_wear_coefficient = 1.0
normal_pressure = normal_lm
[]
[accel_x]
type = NewmarkAccelAux
variable = accel_x
displacement = disp_x
velocity = vel_x
beta = 0.25
execute_on = 'linear timestep_end'
[]
[vel_x]
type = NewmarkVelAux
variable = vel_x
acceleration = accel_x
gamma = 0.5
execute_on = 'linear timestep_end'
[]
[accel_y]
type = NewmarkAccelAux
variable = accel_y
displacement = disp_y
velocity = vel_y
beta = 0.25
execute_on = 'linear timestep_end'
[]
[vel_y]
type = NewmarkVelAux
variable = vel_y
acceleration = accel_y
gamma = 0.5
execute_on = 'linear timestep_end'
[]
[]
[Constraints]
[weighted_gap_lm]
type = ComputeDynamicWeightedGapLMMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = normal_lm
disp_x = disp_x
disp_y = disp_y
use_displaced_mesh = true
c = 1e4
interpolate_normals = false
capture_tolerance = 1.0e-5
newmark_beta = 0.25
newmark_gamma = 0.5
[]
[normal_x]
type = NormalMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = normal_lm
secondary_variable = disp_x
component = x
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[normal_y]
type = NormalMortarMechanicalContact
primary_boundary = 20
secondary_boundary = 10
primary_subdomain = 4
secondary_subdomain = 3
variable = normal_lm
secondary_variable = disp_y
component = y
use_displaced_mesh = true
compute_lm_residuals = false
interpolate_normals = false
[]
[]
[BCs]
[botx]
type = DirichletBC
variable = disp_x
boundary = 40
value = 0.0
[]
[boty]
type = DirichletBC
variable = disp_y
boundary = 40
value = 0.0
[]
[topy]
type = FunctionDirichletBC
variable = disp_y
boundary = 30
function = '${starting_point} * cos(8.0 * pi / 4 * t) + ${offset}'
[]
[leftx]
type = FunctionDirichletBC
variable = disp_x
boundary = 50
function = '1e-2 * t'
[]
[]
[Executioner]
type = Transient
end_time = 0.675
dt = 0.075
dtmin = .075
solve_type = 'NEWTON'
petsc_options = '-snes_converged_reason -ksp_converged_reason -pc_svd_monitor '
'-snes_linesearch_monitor -snes_ksp_ew'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type -pc_factor_shift_type -pc_factor_shift_amount '
petsc_options_value = 'lu superlu_dist NONZERO 1e-15'
nl_max_its = 30
line_search = 'l2'
snesmf_reuse_base = false
[TimeIntegrator]
type = NewmarkBeta
beta = 0.25
gamma = 0.5
[]
[]
[Debug]
show_var_residual_norms = true
[]
[Outputs]
exodus = true
checkpoint = true
[]
[Preconditioning]
[smp]
type = SMP
full = true
[]
[]
[Postprocessors]
active = 'num_nl cumulative contact'
[num_nl]
type = NumNonlinearIterations
[]
[cumulative]
type = CumulativeValuePostprocessor
postprocessor = num_nl
[]
[contact]
type = ContactDOFSetSize
variable = normal_lm
subdomain = '3'
execute_on = 'nonlinear timestep_end'
[]
[]
(modules/tensor_mechanics/test/tests/volumetric_deform_grad/elastic_stress.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'disp_x disp_y disp_z'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
use_displaced_mesh = true
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = disp_y
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = disp_x
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = disp_z
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_z
boundary = front
function = '0.01*t'
[../]
[]
[Materials]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./elastic_stress]
type = ComputeDeformGradBasedStress
deform_grad_name = deformation_gradient
elasticity_tensor_name = elasticity_tensor
stress_name = stress
jacobian_name = Jacobian_mult
block = 0
[../]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
C_ijkl = '2.8e5 1.2e5 1.2e5 2.8e5 1.2e5 2.8e5 0.8e5 0.8e5 0.8e5'
fill_method = symmetric9
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.02
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_hypre_type -ksp_gmres_restart'
petsc_options_value = 'hypre boomeramg 101'
dtmax = 10.0
nl_rel_tol = 1e-10
dtmin = 0.02
num_steps = 10
[]
[Outputs]
csv = true
[]
(modules/tensor_mechanics/test/tests/multi/two_surface04.i)
# Plasticit models:
# SimpleTester with a = 0 and b = 1 and strength = 1
# SimpleTester with a = 1 and b = 1 and strength = 2
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 4.0E-6m in y directions and 2.0E-6 in z direction.
# trial stress_zz = 2 and stress_yy = 4
#
# Then both SimpleTesters should activate initially and return to the "corner" point
# (stress_zz = 1 = stress_yy), but then the plastic multiplier for SimpleTester1 will
# be negative, and so it will be deactivated, and the algorithm will return to
# stress_zz = 0, stress_yy = 2
# internal1 should be zero, internal2 should be 2
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '4E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '2E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[]
[UserObjects]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 2
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = two_surface04
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/contact/test/tests/mortar_dynamics/block-dynamics-friction-action.i)
starting_point = 2e-1
offset = -0.19
[GlobalParams]
displacements = 'disp_x disp_y'
[]
[Mesh]
[file]
type = FileMeshGenerator
file = long-bottom-block-no-lower-d.e
[]
[]
[Variables]
[disp_x]
block = '1 2'
[]
[disp_y]
block = '1 2'
[]
[]
[ICs]
[disp_y]
block = 2
variable = disp_y
value = '${fparse starting_point + offset}'
type = ConstantIC
[]
[]
[Kernels]
[DynamicTensorMechanics]
displacements = 'disp_x disp_y'
generate_output = 'stress_xx stress_yy'
strain = FINITE
block = '1 2'
zeta = 0.05
alpha = 0.0
[]
[inertia_x]
type = InertialForce
variable = disp_x
velocity = vel_x
acceleration = accel_x
beta = 0.25
gamma = 0.5
alpha = 0
eta = 0.0
block = '1 2'
[]
[inertia_y]
type = InertialForce
variable = disp_y
velocity = vel_y
acceleration = accel_y
beta = 0.25
gamma = 0.5
alpha = 0
eta = 0.0
block = '1 2'
[]
[]
[Materials]
[elasticity_2]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[]
[elasticity_1]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e8
poissons_ratio = 0.3
[]
[stress]
type = ComputeFiniteStrainElasticStress
block = '1 2'
[]
[strain]
type = ComputeFiniteStrain
block = '1 2'
[]
[density]
type = GenericConstantMaterial
block = '1 2'
prop_names = 'density'
prop_values = '7750'
[]
[]
[AuxVariables]
[vel_x]
block = '1 2'
[]
[accel_x]
block = '1 2'
[]
[vel_y]
block = '1 2'
[]
[accel_y]
block = '1 2'
[]
[vel_z]
block = '1 2'
[]
[accel_z]
block = '1 2'
[]
[]
[AuxKernels]
[accel_x]
type = NewmarkAccelAux
variable = accel_x
displacement = disp_x
velocity = vel_x
beta = 0.25
execute_on = 'LINEAR timestep_end'
[]
[vel_x]
type = NewmarkVelAux
variable = vel_x
acceleration = accel_x
gamma = 0.5
execute_on = 'LINEAR timestep_end'
[]
[accel_y]
type = NewmarkAccelAux
variable = accel_y
displacement = disp_y
velocity = vel_y
beta = 0.25
execute_on = 'LINEAR timestep_end'
[]
[vel_y]
type = NewmarkVelAux
variable = vel_y
acceleration = accel_y
gamma = 0.5
execute_on = 'LINEAR timestep_end'
[]
[]
[Contact]
[mechanical]
formulation = mortar
model = coulomb
primary = 20
secondary = 10
friction_coefficient = 0.5
c_normal = 1.0e4
c_tangential = 1.0e4
interpolate_normals = false
mortar_dynamics = true
newmark_beta = 0.25
newmark_gamma = 0.5
capture_tolerance = 1.0e-3
[]
[]
[BCs]
[botx]
type = DirichletBC
variable = disp_x
boundary = 40
value = 0.0
[]
[boty]
type = DirichletBC
variable = disp_y
boundary = 40
value = 0.0
[]
[topy]
type = FunctionDirichletBC
variable = disp_y
boundary = 30
function = '${starting_point} * cos(2 * pi / 4 * t) + ${offset}'
[]
[leftx]
type = FunctionDirichletBC
variable = disp_x
boundary = 30 # 50
function = '0' # '1e-2*t'
[]
[]
[Executioner]
type = Transient
end_time = 75
dt = 0.05
dtmin = .005
solve_type = 'PJFNK'
petsc_options = '-snes_converged_reason -ksp_converged_reason -pc_svd_monitor '
'-snes_linesearch_monitor -snes_ksp_ew'
petsc_options_iname = '-pc_type -pc_factor_shift_type -pc_factor_shift_amount -mat_mffd_err '
petsc_options_value = 'lu NONZERO 1e-15 1e-5'
nl_max_its = 50
line_search = 'none'
snesmf_reuse_base = false
[TimeIntegrator]
type = NewmarkBeta
beta = 0.25
gamma = 0.5
[]
[]
[Debug]
show_var_residual_norms = true
[]
[Outputs]
exodus = true
[]
[VectorPostprocessors]
[mechanical_tangential_lm]
type = NodalValueSampler
block = 'mechanical_secondary_subdomain'
variable = mechanical_tangential_lm
sort_by = 'x'
execute_on = TIMESTEP_END
[]
[]
[Preconditioning]
[smp]
type = SMP
full = true
[]
[]
(modules/fsi/test/tests/fsi_acoustics/3D_struc_acoustic/3D_struc_acoustic.i)
# Test for `StructureAcousticInterface` interface kernel. The domain is 3D with lengths
# 10 X 0.1 X 0.1 meters. The fluid domain is on the right and the structural domain
# is on the left. Fluid end is subjected to a 250Hz sine wave with a single peak.
# Structural domain has the same material properties as the fluid. Interface between
# structure and fluid is located at 5.0m in the x-direction. Fluid pressure is recorded
# at (5, 0.05, 0.05). Structural stress is also recorded at the same location. Fluid
# pressure and structural stress should be almost equal and opposite to each other.
#
# Input parameters:
# Dimensions = 3
# Lengths = 10 X 0.1 X 0.1 meters
# Fluid speed of sound = 1500 m/s
# Fluid density = 1e-6 Giga kg/m^3
# Structural bulk modulus = 2.25 GPa
# Structural shear modulus = 0 GPa
# Structural density = 1e-6 Giga kg/m^3
# Fluid domain = true
# Fluid BC = single peak sine wave applied as a pressure on the fluid end
# Structural domain = true
# Structural BC = Neumann BC with value zero applied on the structural end.
# Fluid-structure interface location = 5.0m along the x-direction
[Mesh]
[gen]
type = GeneratedMeshGenerator
dim = 3
nx = 100
ny = 1
nz = 1
xmax = 10
ymax = 0.1
zmax = 0.1
[]
[./subdomain1]
input = gen
type = SubdomainBoundingBoxGenerator
bottom_left = '5.0 0.0 0.0'
block_id = 1
top_right = '10.0 0.1 0.1'
[../]
[./interface1]
type = SideSetsBetweenSubdomainsGenerator
input = subdomain1
primary_block = 1
paired_block = 0
new_boundary = 'interface1'
[../]
[]
[GlobalParams]
[]
[Variables]
[./p]
block = 1
[../]
[./disp_x]
block = 0
[../]
[./disp_y]
block = 0
[../]
[./disp_z]
block = 0
[../]
[]
[AuxVariables]
[./vel_x]
order = FIRST
family = LAGRANGE
block = 0
[../]
[./accel_x]
order = FIRST
family = LAGRANGE
block = 0
[../]
[./vel_y]
order = FIRST
family = LAGRANGE
block = 0
[../]
[./accel_y]
order = FIRST
family = LAGRANGE
block = 0
[../]
[./vel_z]
order = FIRST
family = LAGRANGE
block = 0
[../]
[./accel_z]
order = FIRST
family = LAGRANGE
block = 0
[../]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[Kernels]
[./diffusion]
type = Diffusion
variable = 'p'
block = 1
[../]
[./inertia]
type = AcousticInertia
variable = p
block = 1
[../]
[./DynamicTensorMechanics]
displacements = 'disp_x disp_y disp_z'
block = 0
[../]
[./inertia_x]
type = InertialForce
variable = disp_x
block = 0
[../]
[./inertia_y]
type = InertialForce
variable = disp_y
block = 0
[../]
[./inertia_z]
type = InertialForce
variable = disp_z
block = 0
[../]
[]
[AuxKernels]
[./accel_x]
type = TestNewmarkTI
displacement = disp_x
variable = accel_x
first = false
block = 0
[../]
[./vel_x]
type = TestNewmarkTI
displacement = disp_x
variable = vel_x
block = 0
[../]
[./accel_y]
type = TestNewmarkTI
displacement = disp_y
variable = accel_y
first = false
block = 0
[../]
[./vel_y]
type = TestNewmarkTI
displacement = disp_y
variable = vel_y
block = 0
[../]
[./accel_z]
type = TestNewmarkTI
displacement = disp_z
variable = accel_z
first = false
block = 0
[../]
[./vel_z]
type = TestNewmarkTI
displacement = disp_z
variable = vel_z
block = 0
[../]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
block = 0
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
block = 0
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
block = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
block = 0
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
block = 0
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
block = 0
[../]
[]
[InterfaceKernels]
[./interface1]
type = StructureAcousticInterface
variable = p
neighbor_var = disp_x
boundary = 'interface1'
D = 1e-6
component = 0
[../]
[./interface2]
type = StructureAcousticInterface
variable = p
neighbor_var = disp_y
boundary = 'interface1'
D = 1e-6
component = 1
[../]
[./interface3]
type = StructureAcousticInterface
variable = p
neighbor_var = disp_z
boundary = 'interface1'
D = 1e-6
component = 2
[../]
[]
[BCs]
[./bottom_accel]
type = FunctionDirichletBC
variable = p
boundary = 'right'
function = accel_bottom
[../]
[./disp_x1]
type = NeumannBC
boundary = 'left'
variable = disp_x
value = 0.0
[../]
[./disp_y1]
type = NeumannBC
boundary = 'left'
variable = disp_y
value = 0.0
[../]
[./disp_z1]
type = NeumannBC
boundary = 'left'
variable = disp_z
value = 0.0
[../]
[]
[Functions]
[./accel_bottom]
type = PiecewiseLinear
data_file = ../1D_struc_acoustic/Input_1Peak_highF.csv
scale_factor = 1e-2
format = 'columns'
[../]
[]
[Materials]
[./co_sq]
type = GenericConstantMaterial
prop_names = inv_co_sq
prop_values = 4.44e-7
block = '1'
[../]
[./density0]
type = GenericConstantMaterial
block = 0
prop_names = density
prop_values = 1e-6
[../]
[./elasticity_base]
type = ComputeIsotropicElasticityTensor
bulk_modulus = 2.25
shear_modulus = 0.0
block = 0
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./stress]
type = ComputeFiniteStrainElasticStress
block = 0
[../]
[]
[Preconditioning]
[./andy]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
solve_type = 'NEWTON'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_package'
petsc_options_value = 'lu superlu_dist'
start_time = 0.0
end_time = 0.005
dt = 0.0001
dtmin = 0.00001
nl_abs_tol = 1e-8
nl_rel_tol = 1e-8
l_tol = 1e-8
l_max_its = 25
timestep_tolerance = 1e-8
automatic_scaling = true
[TimeIntegrator]
type = NewmarkBeta
[]
[]
[Postprocessors]
[./p1]
type = PointValue
point = '5.0 0.05 0.05'
variable = p
[../]
[./stress_xx]
type = PointValue
point = '5.0 0.05 0.05'
variable = stress_xx
[../]
[]
[Outputs]
csv = true
exodus = true
perf_graph = true
print_linear_residuals = true
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/crysp.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'ux uy uz'
[]
[Variables]
[./ux]
block = 0
[../]
[./uy]
block = 0
[../]
[./uz]
block = 0
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./rotout]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./e_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./gss1]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'ux uy uz'
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./e_zz]
type = RankTwoAux
variable = e_zz
rank_two_tensor = lage
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./gss1]
type = MaterialStdVectorAux
variable = gss1
property = gss
index = 0
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = uy
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = ux
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = uz
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = uz
boundary = front
function = tdisp
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainCrystalPlasticity
block = 0
gtol = 1e-2
slip_sys_file_name = input_slip_sys.txt
nss = 12
num_slip_sys_flowrate_props = 2 #Number of properties in a slip system
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
hprops = '1.0 541.5 60.8 109.8 2.5'
gprops = '1 4 60.8 5 8 60.8 9 12 60.8'
tan_mod_type = exact
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
block = 0
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'ux uy uz'
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./e_zz]
type = ElementAverageValue
variable = e_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./gss1]
type = ElementAverageValue
variable = gss1
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type'
petsc_options_value = 'lu'
nl_rel_tol = 1e-10
nl_abs_tol = 1e-10
dt = 0.05
dtmax = 10.0
dtmin = 0.05
num_steps = 10
[]
[Outputs]
file_base = out
exodus = true
[]
(modules/tensor_mechanics/test/tests/j2_plasticity/small_deform2.i)
# UserObject J2 test
# apply uniform stretch in z direction to give
# trial stress_zz = 7, so sqrt(3*J2) = 7
# with zero Poisson's ratio, this should return to
# stress_zz = 3, stress_xx = 2 = stress_yy
# (note that stress_zz - stress_xx = stress_zz - stress_yy = 1, so sqrt(3*j2) = 1,
# and that the mean stress remains = 7/3)
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '3.5E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = f
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = f
[../]
[./iter]
type = PointValue
point = '0 0 0'
variable = iter
[../]
[]
[UserObjects]
[./str]
type = TensorMechanicsHardeningConstant
value = 1
[../]
[./j2]
type = TensorMechanicsPlasticJ2
yield_strength = str
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = j2
debug_fspb = crash
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = small_deform2
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform1_uo.i)
# apply uniform stretch in x, y and z directions.
# With cohesion = 10, friction_angle = 60deg, tip_smoother = 4, the
# algorithm should return to
# sigma_m = (10*Cos(60) - 4)/Sin(60) = 1.1547
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '1E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = f
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = f
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 10
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 60
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 5
convert_to_radians = true
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 4
mc_edge_smoother = 25
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = mc
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = 1
debug_jac_at_intnl = 1
debug_stress_change = 1E-5
debug_pm_change = 1E-6
debug_intnl_change = 1E-6
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = small_deform1_uo
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/finite_strain_tensor_mechanics_tests/finite_strain_patch.i)
# Patch Test
# This test is designed to compute constant xx, yy, zz, xy, yz, and zx
# stress on a set of irregular hexes. The mesh is composed of one
# block with seven elements. The elements form a unit cube with one
# internal element. There is a nodeset for each exterior node.
# The cube is displaced by 1e-6 units in x, 2e-6 in y, and 3e-6 in z.
# The faces are sheared as well (1e-6, 2e-6, and 3e-6 for xy, yz, and
# zx). This gives a uniform strain/stress state for all six unique
# tensor components.
# With Young's modulus at 1e6 and Poisson's ratio at 0, the shear
# modulus is 5e5 (G=E/2/(1+nu)). Therefore,
#
# stress xx = 1e6 * 1e-6 = 1
# stress yy = 1e6 * 2e-6 = 2
# stress zz = 1e6 * 3e-6 = 3
# stress xy = 2 * 5e5 * 1e-6 / 2 = 0.5
# (2 * G * gamma_xy / 2 = 2 * G * epsilon_xy)
# stress yz = 2 * 5e5 * 2e-6 / 2 = 1
# stress zx = 2 * 5e5 * 3e-6 / 2 = 1.5
[Mesh]
# Comment
# Mesh
file = patch_mesh.e
[]
[GlobalParams]
displacements = 'disp_x disp_y disp_z'
[]
[Functions]
# Functions
[./rampConstant1]
type = PiecewiseLinear
x = '0. 1. 2.'
y = '0. 1. 1.'
scale_factor = 1e-6
[../]
[./rampConstant2]
type = PiecewiseLinear
x = '0. 1. 2.'
y = '0. 1. 1.'
scale_factor = 2e-6
[../]
[./rampConstant3]
type = PiecewiseLinear
x = '0. 1. 2.'
y = '0. 1. 1.'
scale_factor = 3e-6
[../]
[./rampConstant4]
type = PiecewiseLinear
x = '0. 1. 2.'
y = '0. 1. 1.'
scale_factor = 4e-6
[../]
[./rampConstant6]
type = PiecewiseLinear
x = '0. 1. 2.'
y = '0. 1. 1.'
scale_factor = 6e-6
[../]
[]
[Variables]
# Variables
[./disp_x]
order = FIRST
family = LAGRANGE
[../]
[./disp_y]
order = FIRST
family = LAGRANGE
[../]
[./disp_z]
order = FIRST
family = LAGRANGE
[../]
[]
[AuxVariables]
# AuxVariables
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zx]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
[../]
[]
[AuxKernels]
# AuxKernels
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zx
index_i = 2
index_j = 0
[../]
[]
[BCs]
# BCs
[./node1_x]
type = DirichletBC
variable = disp_x
boundary = 1
value = 0.0
[../]
[./node1_y]
type = FunctionDirichletBC
variable = disp_y
boundary = 1
function = rampConstant2
[../]
[./node1_z]
type = FunctionDirichletBC
variable = disp_z
boundary = 1
function = rampConstant3
[../]
[./node2_x]
type = FunctionDirichletBC
variable = disp_x
boundary = 2
function = rampConstant1
[../]
[./node2_y]
type = FunctionDirichletBC
variable = disp_y
boundary = 2
function = rampConstant2
[../]
[./node2_z]
type = FunctionDirichletBC
variable = disp_z
boundary = 2
function = rampConstant6
[../]
[./node3_x]
type = FunctionDirichletBC
variable = disp_x
boundary = 3
function = rampConstant1
[../]
[./node3_y]
type = DirichletBC
variable = disp_y
boundary = 3
value = 0.0
[../]
[./node3_z]
type = FunctionDirichletBC
variable = disp_z
boundary = 3
function = rampConstant3
[../]
[./node4_x]
type = DirichletBC
variable = disp_x
boundary = 4
value = 0.0
[../]
[./node4_y]
type = DirichletBC
variable = disp_y
boundary = 4
value = 0.0
[../]
[./node4_z]
type = DirichletBC
variable = disp_z
boundary = 4
value = 0.0
[../]
[./node5_x]
type = FunctionDirichletBC
variable = disp_x
boundary = 5
function = rampConstant1
[../]
[./node5_y]
type = FunctionDirichletBC
variable = disp_y
boundary = 5
function = rampConstant4
[../]
[./node5_z]
type = FunctionDirichletBC
variable = disp_z
boundary = 5
function = rampConstant3
[../]
[./node6_x]
type = FunctionDirichletBC
variable = disp_x
boundary = 6
function = rampConstant2
[../]
[./node6_y]
type = FunctionDirichletBC
variable = disp_y
boundary = 6
function = rampConstant4
[../]
[./node6_z]
type = FunctionDirichletBC
variable = disp_z
boundary = 6
function = rampConstant6
[../]
[./node7_x]
type = FunctionDirichletBC
variable = disp_x
boundary = 7
function = rampConstant2
[../]
[./node7_y]
type = FunctionDirichletBC
variable = disp_y
boundary = 7
function = rampConstant2
[../]
[./node7_z]
type = FunctionDirichletBC
variable = disp_z
boundary = 7
function = rampConstant3
[../]
[./node8_x]
type = FunctionDirichletBC
variable = disp_x
boundary = 8
function = rampConstant1
[../]
[./node8_y]
type = FunctionDirichletBC
variable = disp_y
boundary = 8
function = rampConstant2
[../]
[./node8_z]
type = DirichletBC
variable = disp_z
boundary = 8
value = 0.0
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = '1 2 3 4 5 6 7'
C_ijkl = '1.0e6 0.0 0.0 1.0e6 0.0 1.0e6 0.5e6 0.5e6 0.5e6'
fill_method = symmetric9
[../]
[./strain]
type = ComputeFiniteStrain
block = '1 2 3 4 5 6 7'
displacements = 'disp_x disp_y disp_z'
[../]
[./stress]
type = ComputeFiniteStrainElasticStress
block = '1 2 3 4 5 6 7'
[../]
[]
[Preconditioning]
[./SMP]
type = SMP
full = true
[../]
[]
[Executioner]
# Executioner
type = Transient
solve_type = 'NEWTON'
nl_abs_tol = 1e-10
l_max_its = 20
start_time = 0.0
dt = 1.0
num_steps = 2
petsc_options_iname = -pc_type
petsc_options_value = lu
end_time = 2.0
[]
[Outputs]
exodus = true
[] # Output
(modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/crysp_fileread.i)
[Mesh]
type = GeneratedMesh
dim = 3
nx=1
ny=1
nz=1
xmin=0.0
xmax=1.0
ymin=0.0
ymax=1.0
zmin=0.0
zmax=1.0
elem_type = HEX8
displacements = 'disp_x disp_y disp_z'
[]
[Variables]
[./disp_x]
block = 0
[../]
[./disp_y]
block = 0
[../]
[./disp_z]
block = 0
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./rotout]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./e_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./gss1]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = 'initial timestep_end'
block = 0
[../]
[./e_zz]
type = RankTwoAux
variable = e_zz
rank_two_tensor = lage
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./gss1]
type = MaterialStdVectorAux
variable = gss1
property = gss
index = 0
execute_on = 'initial timestep_end'
block = 0
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = disp_y
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = disp_x
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = disp_z
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_z
boundary = front
function = tdisp
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainCrystalPlasticity
block = 0
gtol = 1e-2
slip_sys_file_name = input_slip_sys.txt
slip_sys_res_prop_file_name = input_slip_sys_res.txt
slip_sys_flow_prop_file_name = input_slip_sys_flow_prop.txt
hprops = '1.0 541.5 60.8 109.8 2.5'
nss = 12
intvar_read_type = slip_sys_res_file
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
block = 0
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
execute_on = 'initial timestep_end'
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
execute_on = 'initial timestep_end'
[../]
[./e_zz]
type = ElementAverageValue
variable = e_zz
execute_on = 'initial timestep_end'
[../]
[./gss1]
type = ElementAverageValue
variable = gss1
execute_on = 'initial timestep_end'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type'
petsc_options_value = 'lu'
nl_rel_tol = 1e-10
nl_abs_tol = 1e-10
dt = 0.05
dtmax = 10.0
dtmin = 0.05
num_steps = 10
[]
[Outputs]
file_base = crysp_fileread_out
exodus = true
[]
(modules/tensor_mechanics/test/tests/j2_plasticity/hard1.i)
# UserObject J2 test, with hardening, but with rate=0
# apply uniform compression in x direction to give
# trial stress_xx = -5, so sqrt(3*J2) = 5
# with zero Poisson's ratio, this should return to
# stress_xx = -3, stress_yy = -1 = stress_zz,
# for strength = 2
# (note that stress_xx - stress_yy = stress_xx - stress_zz = -2, so sqrt(3*j2) = 2,
# and that the mean stress remains = -5/3)
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '-2.5E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = f
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = f
[../]
[./iter]
type = PointValue
point = '0 0 0'
variable = iter
[../]
[]
[UserObjects]
[./str]
type = TensorMechanicsHardeningConstant
value = 2
[../]
[./j2]
type = TensorMechanicsPlasticJ2
yield_strength = str
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = j2
debug_fspb = crash
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = hard1
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/contact/test/tests/verification/patch_tests/brick_1/brick1_template1.i)
[GlobalParams]
volumetric_locking_correction = true
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
file = brick1_mesh.e
[]
[Problem]
type = ReferenceResidualProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./penetration]
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./saved_z]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./diag_saved_z]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./inc_slip_z]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./accum_slip_z]
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y saved_z'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 4
paired_boundary = 3
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./ref_resid_x]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_x
[../]
[./ref_resid_y]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_y
[../]
[./sigma_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./sigma_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./disp_x5]
type = NodalVariableValue
nodeid = 4
variable = disp_x
[../]
[./disp_x8]
type = NodalVariableValue
nodeid = 7
variable = disp_x
[../]
[./disp_x13]
type = NodalVariableValue
nodeid = 12
variable = disp_x
[../]
[./disp_x16]
type = NodalVariableValue
nodeid = 15
variable = disp_x
[../]
[./disp_y5]
type = NodalVariableValue
nodeid = 4
variable = disp_y
[../]
[./disp_y8]
type = NodalVariableValue
nodeid = 7
variable = disp_y
[../]
[./disp_y13]
type = NodalVariableValue
nodeid = 12
variable = disp_y
[../]
[./disp_y16]
type = NodalVariableValue
nodeid = 15
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./bot_y]
type = DirichletBC
variable = disp_y
boundary = 1
value = 0.0
[../]
[./side_x]
type = DirichletBC
variable = disp_x
boundary = 2
value = 0.0
[../]
[./back_z]
type = DirichletBC
variable = disp_z
boundary = 6
value = 0.0
[../]
[./top_press]
type = Pressure
variable = disp_y
boundary = 5
factor = 109.89
[../]
[]
[Materials]
[./bot_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./bot_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./bot_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./top_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./top_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./top_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-9
nl_rel_tol = 1e-8
l_max_its = 50
nl_max_its = 100
dt = 1.0
end_time = 1.0
num_steps = 10
dtmin = 1.0
l_tol = 1e-5
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '1 3 4 5'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '1 3 4 5'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
show = 'bot_react_x bot_react_y disp_x5 disp_x8 disp_x13 disp_x16 disp_y5 disp_y8 disp_y13 disp_y16 stress_yy stress_zz top_react_x top_react_y x_disp y_disp cont_press'
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./leftright]
secondary = 3
primary = 4
normalize_penalty = true
tangential_tolerance = 1e-3
penalty = 1e+9
[../]
[]
(modules/contact/test/tests/verification/patch_tests/brick_1/brick1_template2.i)
[GlobalParams]
volumetric_locking_correction = true
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
file = brick1_mesh.e
[]
[Problem]
type = AugmentedLagrangianContactProblem
maximum_lagrangian_update_iterations = 200
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./penetration]
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./saved_z]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./diag_saved_z]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./inc_slip_z]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./accum_slip_z]
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y saved_z'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 4
paired_boundary = 3
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./ref_resid_x]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_x
[../]
[./ref_resid_y]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_y
[../]
[./sigma_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./sigma_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./disp_x5]
type = NodalVariableValue
nodeid = 4
variable = disp_x
[../]
[./disp_x8]
type = NodalVariableValue
nodeid = 7
variable = disp_x
[../]
[./disp_x13]
type = NodalVariableValue
nodeid = 12
variable = disp_x
[../]
[./disp_x16]
type = NodalVariableValue
nodeid = 15
variable = disp_x
[../]
[./disp_y5]
type = NodalVariableValue
nodeid = 4
variable = disp_y
[../]
[./disp_y8]
type = NodalVariableValue
nodeid = 7
variable = disp_y
[../]
[./disp_y13]
type = NodalVariableValue
nodeid = 12
variable = disp_y
[../]
[./disp_y16]
type = NodalVariableValue
nodeid = 15
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./bot_y]
type = DirichletBC
variable = disp_y
boundary = 1
value = 0.0
[../]
[./side_x]
type = DirichletBC
variable = disp_x
boundary = 2
value = 0.0
[../]
[./back_z]
type = DirichletBC
variable = disp_z
boundary = 6
value = 0.0
[../]
[./top_press]
type = Pressure
variable = disp_y
boundary = 5
factor = 109.89
[../]
[]
[Materials]
[./bot_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./bot_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./bot_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./top_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./top_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./top_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-9
nl_rel_tol = 1e-8
l_max_its = 50
nl_max_its = 100
dt = 1.0
end_time = 1.0
num_steps = 10
dtmin = 1.0
l_tol = 1e-5
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '1 3 4 5'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '1 3 4 5'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
show = 'bot_react_x bot_react_y disp_x5 disp_x8 disp_x13 disp_x16 disp_y5 disp_y8 disp_y13 disp_y16 stress_yy stress_zz top_react_x top_react_y x_disp y_disp cont_press'
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./leftright]
secondary = 3
primary = 4
normalize_penalty = true
tangential_tolerance = 1e-3
penalty = 5e+9
al_penetration_tolerance = 1e-8
[../]
[]
(modules/tensor_mechanics/test/tests/multi/six_surface14.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 3
# SimpleTester3 with a = 0 and b = 1 and strength = 1.1
# SimpleTester4 with a = 1 and b = 0 and strength = 1.1
# SimpleTester5 with a = 1 and b = 1 and strength = 3.1
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 2.1E-6m in y direction and 3E-6 in z direction.
# trial stress_yy = 2.1 and stress_zz = 3.0
#
# This is similar to three_surface14.i, and a description is found there.
# The result should be stress_zz=1=stress_yy, with internal0=2
# and internal1=1.1
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '2.1E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '3.0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./f3]
order = CONSTANT
family = MONOMIAL
[../]
[./f4]
order = CONSTANT
family = MONOMIAL
[../]
[./f5]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[./int3]
order = CONSTANT
family = MONOMIAL
[../]
[./int4]
order = CONSTANT
family = MONOMIAL
[../]
[./int5]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./f3]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 3
variable = f3
[../]
[./f4]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 4
variable = f4
[../]
[./f5]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 5
variable = f5
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[./int3]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 3
variable = int3
[../]
[./int4]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 4
variable = int4
[../]
[./int5]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 5
variable = int5
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./f3]
type = PointValue
point = '0 0 0'
variable = f3
[../]
[./f4]
type = PointValue
point = '0 0 0'
variable = f4
[../]
[./f5]
type = PointValue
point = '0 0 0'
variable = f5
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[./int3]
type = PointValue
point = '0 0 0'
variable = int3
[../]
[./int4]
type = PointValue
point = '0 0 0'
variable = int4
[../]
[./int5]
type = PointValue
point = '0 0 0'
variable = int5
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 3
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple3]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1.1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple4]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1.1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple5]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 3.1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2 simple3 simple4 simple5'
max_NR_iterations = 4
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1 1'
debug_jac_at_intnl = '1 1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = six_surface14
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/crysp_save_euler.i)
[Mesh]
type = GeneratedMesh
dim = 2
elem_type = QUAD4
displacements = 'disp_x disp_y'
nx = 2
ny = 2
[]
[Variables]
[./disp_x]
block = 0
[../]
[./disp_y]
block = 0
[../]
[]
[GlobalParams]
volumetric_locking_correction = true
[]
[AuxVariables]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./e_yy]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./fp_yy]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./rotout]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./gss1]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./euler1]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./euler2]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./euler3]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[UserObjects]
[./prop_read]
type = PropertyReadFile
prop_file_name = 'euler_ang_file.txt'
# Enter file data as prop#1, prop#2, .., prop#nprop
nprop = 3
read_type = element
[../]
[]
[AuxKernels]
[./stress_yy]
type = RankTwoAux
variable = stress_yy
rank_two_tensor = stress
index_j = 1
index_i = 1
execute_on = timestep_end
block = 0
[../]
[./e_yy]
type = RankTwoAux
variable = e_yy
rank_two_tensor = lage
index_j = 1
index_i = 1
execute_on = timestep_end
block = 0
[../]
[./fp_yy]
type = RankTwoAux
variable = fp_yy
rank_two_tensor = fp
index_j = 1
index_i = 1
execute_on = timestep_end
block = 0
[../]
[./gss1]
type = MaterialStdVectorAux
variable = gss1
property = gss
index = 0
execute_on = timestep_end
block = 0
[../]
[./euler1]
type = MaterialRealVectorValueAux
variable = euler1
property = Euler_angles
component = 0
execute_on = timestep_end
block = 0
[../]
[./euler2]
type = MaterialRealVectorValueAux
variable = euler2
property = Euler_angles
component = 1
execute_on = timestep_end
block = 0
[../]
[./euler3]
type = MaterialRealVectorValueAux
variable = euler3
property = Euler_angles
component = 2
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./fix_x]
type = DirichletBC
variable = disp_x
boundary = 'left'
value = 0
[../]
[./fix_y]
type = DirichletBC
variable = disp_y
boundary = 'bottom'
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_y
boundary = top
function = tdisp
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainCrystalPlasticity
block = 0
gtol = 1e-2
slip_sys_file_name = input_slip_sys.txt
nss = 12
num_slip_sys_flowrate_props = 2 #Number of properties in a slip system
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
hprops = '1.0 541.5 60.8 109.8 2.5'
gprops = '1 4 60.8 5 8 60.8 9 12 60.8'
tan_mod_type = exact
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
block = 0
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
read_prop_user_object = prop_read
[../]
[]
[Postprocessors]
[./stress_yy]
type = ElementAverageValue
variable = stress_yy
block = 'ANY_BLOCK_ID 0'
[../]
[./e_yy]
type = ElementAverageValue
variable = e_yy
block = 'ANY_BLOCK_ID 0'
[../]
[./fp_yy]
type = ElementAverageValue
variable = fp_yy
block = 'ANY_BLOCK_ID 0'
[../]
[./gss1]
type = ElementAverageValue
variable = gss1
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type'
petsc_options_value = 'lu'
nl_rel_tol = 1e-10
nl_abs_tol = 1e-10
dt = 0.01
dtmax = 10.0
dtmin = 0.01
num_steps = 10
[]
[Outputs]
file_base = crysp_save_euler_out
exodus = true
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y'
use_displaced_mesh = true
[../]
[]
(modules/tensor_mechanics/test/tests/auxkernels/ranktwoscalaraux.i)
[Mesh]
displacements = 'disp_x disp_y disp_z'
[generated_mesh]
type = GeneratedMeshGenerator
elem_type = HEX8
dim = 3
nx = 1
ny = 1
nz = 1
xmin = 0.0
xmax = 1.0
ymin = 0.0
ymax = 1.0
zmin = 0.0
zmax = 1.0
[]
[node]
type = ExtraNodesetGenerator
coord = '0.0 0.0 0.0'
new_boundary = 6
input = generated_mesh
[]
[snode]
type = ExtraNodesetGenerator
coord = '1.0 0.0 0.0'
new_boundary = 7
input = node
[]
[]
[Variables]
[./disp_x]
order = FIRST
family = LAGRANGE
[../]
[./disp_y]
order = FIRST
family = LAGRANGE
[../]
[./disp_z]
order = FIRST
family = LAGRANGE
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[Materials]
[./fplastic]
type = FiniteStrainPlasticMaterial
block = 0
yield_stress='0. 445. 0.05 610. 0.1 680. 0.38 810. 0.95 920. 2. 950.'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
C_ijkl = '2.827e5 1.21e5 1.21e5 2.827e5 1.21e5 2.827e5 0.808e5 0.808e5 0.808e5'
fill_method = symmetric9
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[]
[Functions]
[./topfunc]
type = ParsedFunction
value = 't'
[../]
[]
[BCs]
[./bottom3]
type = DirichletBC
variable = disp_z
boundary = 0
value = 0.0
[../]
[./top]
type = FunctionDirichletBC
variable = disp_z
boundary = 5
function = topfunc
[../]
[./corner1]
type = DirichletBC
variable = disp_x
boundary = 6
value = 0.0
[../]
[./corner2]
type = DirichletBC
variable = disp_y
boundary = 6
value = 0.0
[../]
[./corner3]
type = DirichletBC
variable = disp_z
boundary = 6
value = 0.0
[../]
[./side1]
type = DirichletBC
variable = disp_y
boundary = 7
value = 0.0
[../]
[./side2]
type = DirichletBC
variable = disp_z
boundary = 7
value = 0.0
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./vonmises]
order = CONSTANT
family = MONOMIAL
[../]
[./hydrostatic]
order = CONSTANT
family = MONOMIAL
[../]
[./L2norm]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./vonmises]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = vonmises
scalar_type = VonMisesStress
[../]
[./hydrostatic]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = hydrostatic
scalar_type = Hydrostatic
[../]
[./L2norm]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = L2norm
scalar_type = L2norm
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./vonmises]
type = ElementAverageValue
variable = vonmises
[../]
[./hydrostatic]
type = ElementAverageValue
variable = hydrostatic
[../]
[./L2norm]
type = ElementAverageValue
variable = L2norm
[../]
[]
[Executioner]
type = Transient
dt=0.1
dtmin=0.1
dtmax=1
end_time=1.0
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
nl_rel_tol = 1e-10
nl_abs_tol = 1e-10
[]
[Outputs]
exodus = true
csv = true
[]
(modules/combined/test/tests/cavity_pressure/3d.i)
#
# Cavity Pressure Test
#
# This test is designed to compute an internal pressure based on
# p = n * R * T / V
# where
# p is the pressure
# n is the amount of material in the volume (moles)
# R is the universal gas constant
# T is the temperature
# V is the volume
#
# The mesh is composed of one block (1) with an interior cavity of volume 8.
# Block 2 sits in the cavity and has a volume of 1. Thus, the total
# initial volume is 7.
# The test adjusts n, T, and V in the following way:
# n => n0 + alpha * t
# T => T0 + beta * t
# V => V0 + gamma * t
# with
# alpha = n0
# beta = T0 / 2
# gamma = - (0.003322259...) * V0
# T0 = 240.54443866068704
# V0 = 7
# n0 = f(p0)
# p0 = 100
# R = 8.314472 J * K^(-1) * mol^(-1)
#
# So, n0 = p0 * V0 / R / T0 = 100 * 7 / 8.314472 / 240.544439
# = 0.35
#
# The parameters combined at t = 1 gives p = 301.
#
[GlobalParams]
displacements = 'disp_x disp_y disp_z'
volumetric_locking_correction = true
[]
[Mesh]
file = 3d.e
[]
[Functions]
[./displ_positive]
type = PiecewiseLinear
x = '0 1'
y = '0 0.0029069767441859684'
[../]
[./displ_negative]
type = PiecewiseLinear
x = '0 1'
y = '0 -0.0029069767441859684'
[../]
[./temp1]
type = PiecewiseLinear
x = '0 1'
y = '1 1.5'
scale_factor = 240.54443866068704
[../]
[./material_input_function]
type = PiecewiseLinear
x = '0 1'
y = '0 0.35'
[../]
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[./temp]
initial_condition = 240.54443866068704
[../]
[./material_input]
[../]
[]
[AuxVariables]
[./pressure_residual_x]
[../]
[./pressure_residual_y]
[../]
[./pressure_residual_z]
[../]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zx]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
[../]
[./heat]
type = Diffusion
variable = temp
use_displaced_mesh = true
[../]
[./material_input_dummy]
type = Diffusion
variable = material_input
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
index_i = 0
index_j = 0
variable = stress_xx
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
index_i = 1
index_j = 1
variable = stress_yy
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
index_i = 2
index_j = 2
variable = stress_zz
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
index_i = 0
index_j = 1
variable = stress_xy
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
index_i = 1
index_j = 2
variable = stress_yz
[../]
[./stress_zx]
type = RankTwoAux
rank_two_tensor = stress
index_i = 2
index_j = 0
variable = stress_zx
[../]
[]
[BCs]
[./no_x_exterior]
type = DirichletBC
variable = disp_x
boundary = '7 8'
value = 0.0
[../]
[./no_y_exterior]
type = DirichletBC
variable = disp_y
boundary = '9 10'
value = 0.0
[../]
[./no_z_exterior]
type = DirichletBC
variable = disp_z
boundary = '11 12'
value = 0.0
[../]
[./prescribed_left]
type = FunctionDirichletBC
variable = disp_x
boundary = 13
function = displ_positive
[../]
[./prescribed_right]
type = FunctionDirichletBC
variable = disp_x
boundary = 14
function = displ_negative
[../]
[./no_y]
type = DirichletBC
variable = disp_y
boundary = '15 16'
value = 0.0
[../]
[./no_z]
type = DirichletBC
variable = disp_z
boundary = '17 18'
value = 0.0
[../]
[./no_x_interior]
type = DirichletBC
variable = disp_x
boundary = '1 2'
value = 0.0
[../]
[./no_y_interior]
type = DirichletBC
variable = disp_y
boundary = '3 4'
value = 0.0
[../]
[./no_z_interior]
type = DirichletBC
variable = disp_z
boundary = '5 6'
value = 0.0
[../]
[./temperatureInterior]
type = FunctionDirichletBC
boundary = 100
function = temp1
variable = temp
[../]
[./MaterialInput]
type = FunctionDirichletBC
boundary = '100 13 14 15 16'
function = material_input_function
variable = material_input
[../]
[./CavityPressure]
[./1]
boundary = 100
initial_pressure = 100
material_input = materialInput
R = 8.314472
temperature = aveTempInterior
volume = internalVolume
startup_time = 0.5
output = ppress
save_in = 'pressure_residual_x pressure_residual_y pressure_residual_z'
[../]
[../]
[]
[Materials]
[./elast_tensor1]
type = ComputeIsotropicElasticityTensor
youngs_modulus = 1e1
poissons_ratio = 0
block = 1
[../]
[./strain1]
type = ComputeFiniteStrain
block = 1
[../]
[./stress1]
type = ComputeFiniteStrainElasticStress
block = 1
[../]
[./elast_tensor2]
type = ComputeIsotropicElasticityTensor
youngs_modulus = 1e6
poissons_ratio = 0
block = 2
[../]
[./strain2]
type = ComputeFiniteStrain
block = 2
[../]
[./stress2]
type = ComputeFiniteStrainElasticStress
block = 2
[../]
[]
[Executioner]
type = Transient
petsc_options_iname = '-pc_type -sub_pc_type'
petsc_options_value = 'asm lu'
nl_rel_tol = 1e-12
l_tol = 1e-12
l_max_its = 20
dt = 0.5
end_time = 1.0
[]
[Postprocessors]
[./internalVolume]
type = InternalVolume
boundary = 100
execute_on = 'initial linear'
[../]
[./aveTempInterior]
type = SideAverageValue
boundary = 100
variable = temp
execute_on = 'initial linear'
[../]
[./materialInput]
type = SideAverageValue
boundary = '7 8 9 10 11 12'
variable = material_input
execute_on = linear
[../]
[]
[Outputs]
exodus = true
[]
(modules/tensor_mechanics/test/tests/volumetric_deform_grad/volumetric_strain_interface.i)
#This test has volumetric deformation gradient as identity
#Test the interface
#Results should match with elasticity
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'disp_x disp_y disp_z'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
use_displaced_mesh = true
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = disp_y
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = disp_x
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = disp_z
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_z
boundary = front
function = '0.01*t'
[../]
[]
[Materials]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./volumetric_strain]
type = ComputeVolumetricDeformGrad
pre_deform_grad_name = deformation_gradient
volumetric_deform_grad_name = volumetric_deformation_gradient
post_deform_grad_name = elastic_deformation_gradient
block = 0
[../]
[./elastic_stress]
type = ComputeDeformGradBasedStress
deform_grad_name = elastic_deformation_gradient
elasticity_tensor_name = elasticity_tensor
stress_name = elastic_stress
jacobian_name = elastic_jacobian
block = 0
[../]
[./corrected_stress]
type = VolumeDeformGradCorrectedStress
pre_stress_name = elastic_stress
deform_grad_name = volumetric_deformation_gradient
pre_jacobian_name = elastic_jacobian
stress_name = stress
jacobian_name = Jacobian_mult
block = 0
[../]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
C_ijkl = '2.8e5 1.2e5 1.2e5 2.8e5 1.2e5 2.8e5 0.8e5 0.8e5 0.8e5'
fill_method = symmetric9
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.02
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_hypre_type -ksp_gmres_restart'
petsc_options_value = 'hypre boomeramg 101'
dtmax = 10.0
nl_rel_tol = 1e-10
dtmin = 0.02
num_steps = 10
[]
[Outputs]
csv = true
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform4.i)
# apply repeated stretches in z direction, and smaller stretches in the x and y directions
# so that sigma_II = sigma_III,
# which means that lode angle = -30deg.
# The allows yield surface in meridional plane to be mapped out
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0.25E-6*x*sin(t)'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0.25E-6*y*sin(t)'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z*t'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./mc_int]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./mc_int_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_internal_parameter
variable = mc_int
[../]
[./yield_fcn_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./internal]
type = PointValue
point = '0 0 0'
variable = mc_int
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = yield_fcn
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 10
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 50
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningExponential
value_0 = 0
value_residual = 0.8726646 # 50deg
rate = 3000.0
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 4
mc_edge_smoother = 20
yield_function_tolerance = 1E-8
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = mc
debug_fspb = crash
[../]
[]
[Executioner]
end_time = 30
dt = 1
type = Transient
[]
[Outputs]
file_base = small_deform4
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform_hard2.i)
# apply uniform stretches in x, y and z directions.
# let friction_angle = 60deg, friction_angle_residual=10deg, friction_angle_rate = 0.5E4
# With cohesion = C, friction_angle = phi, tip_smoother = T, the
# algorithm should return to
# sigma_m = (C*Cos(phi) - T)/Sin(phi)
# Or, when T=C,
# phi = 2*pi*n - 2*arctan(sigma_m/C)
# This allows checking of the relationship for phi
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '1E-6*x*t'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1E-6*y*t'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z*t'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./mc_int]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./mc_int_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_internal_parameter
variable = mc_int
[../]
[./yield_fcn_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./internal]
type = PointValue
point = '0 0 0'
variable = mc_int
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = yield_fcn
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 10
[../]
[./mc_phi]
type = TensorMechanicsHardeningExponential
value_0 = 1.04719755 # 60deg
value_residual = 0.17453293 # 10deg
rate = 0.5E4
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 5
convert_to_radians = true
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 10
mc_edge_smoother = 25
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = mc
debug_fspb = crash
debug_jac_at_stress = '10 1 2 1 10 3 2 3 10'
debug_jac_at_pm = 1
debug_jac_at_intnl = 1E-3
debug_stress_change = 1E-5
debug_pm_change = 1E-6
debug_intnl_change = 1E-6
[../]
[]
[Executioner]
end_time = 10
dt = 1
type = Transient
[]
[Outputs]
file_base = small_deform_hard2
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/drucker_prager/random_hyperbolic.i)
# drucker-prager hyperbolic.
# apply many random large deformations, checking that the algorithm returns correctly to
# the yield surface each time.
[Mesh]
type = GeneratedMesh
dim = 3
nx = 100
ny = 125
nz = 1
xmin = 0
xmax = 100
ymin = 0
ymax = 125
zmin = 0
zmax = 1
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[ICs]
[./x]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_x
[../]
[./y]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_y
[../]
[./z]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_z
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0'
[../]
[]
[AuxVariables]
[./yield_fcn]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./yield_fcn_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./yield_fcn_at_zero]
type = PointValue
point = '0 0 0'
variable = yield_fcn
outputs = 'console'
[../]
[./should_be_zero]
type = FunctionValuePostprocessor
function = should_be_zero_fcn
[../]
[./av_iter]
type = ElementAverageValue
variable = iter
outputs = 'console'
[../]
[]
[Functions]
[./should_be_zero_fcn]
type = ParsedFunction
value = 'if(a<1E-3,0,a)'
vars = 'a'
vals = 'yield_fcn_at_zero'
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 1E3
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 30
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 5
convert_to_radians = true
[../]
[./dp]
type = TensorMechanicsPlasticDruckerPragerHyperbolic
mc_cohesion = mc_coh
mc_friction_angle = mc_phi
mc_dilation_angle = mc_psi
smoother = 0.1E3
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-6
use_custom_returnMap = true
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0.7E7 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./dp]
type = ComputeMultiPlasticityStress
block = 0
max_NR_iterations = 1000
ep_plastic_tolerance = 1E-6
min_stepsize = 1E-3
plastic_models = dp
debug_fspb = crash
deactivation_scheme = safe
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = random_hyperbolic
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/multi/paper1.i)
# This runs the models mentioned in the first example of the Multi-Surface paper
#
# Plasticity models:
# SimpleTester with a = 1 and b = 0 and strength = 1E9 (only does elasticity)
# SimpleTester with a = 1 and b = 0 and strength = 0
# SimpleTester with a = 1 and b = 0 and strength = 1E-3
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A line of elements is perturbed randomly, and return to the yield surface at each quadpoint is checked
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 125
nz = 1
xmin = 0
xmax = 1
ymin = 0
ymax = 125
zmin = 0
zmax = 1
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[ICs]
[./x]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_x
[../]
[./y]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_y
[../]
[./z]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_z
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./linesearch]
order = CONSTANT
family = MONOMIAL
[../]
[./ld]
order = CONSTANT
family = MONOMIAL
[../]
[./constr_added]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./linesearch]
type = MaterialRealAux
property = plastic_linesearch_needed
variable = linesearch
[../]
[./ld]
type = MaterialRealAux
property = plastic_linear_dependence_encountered
variable = ld
[../]
[./constr_added]
type = MaterialRealAux
property = plastic_constraints_added
variable = constr_added
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./max_iter]
type = ElementExtremeValue
variable = iter
outputs = console
[../]
[./av_linesearch]
type = ElementAverageValue
variable = linesearch
outputs = console
[../]
[./av_ld]
type = ElementAverageValue
variable = ld
outputs = console
[../]
[./av_constr_added]
type = ElementAverageValue
variable = constr_added
outputs = console
[../]
[./av_iter]
type = ElementAverageValue
variable = iter
outputs = console
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1E9
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 0
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1E-3
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[]
[Materials]
active = 'elasticity_tensor strain single'
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./elastic_model]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-7
plastic_models = 'simple0'
[../]
[./single]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-7
plastic_models = 'simple1'
[../]
[./double]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-7
plastic_models = 'simple1 simple2'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = paper1
exodus = false
csv = true
[]
(modules/tensor_mechanics/test/tests/multi/eight_surface14.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 3
# SimpleTester3 with a = 0 and b = 1 and strength = 1.1
# SimpleTester4 with a = 1 and b = 0 and strength = 1.1
# SimpleTester5 with a = 1 and b = 1 and strength = 3.1
# SimpleTester6 with a = 1 and b = 2 and strength = 3.1
# SimpleTester7 with a = 2 and b = 1 and strength = 3.1
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 2.1E-6m in y direction and 3E-6 in z direction.
# trial stress_yy = 2.1 and stress_zz = 3.0
#
# This is similar to three_surface14.i, and a description is found there.
# The result should be stress_zz=1=stress_yy, with internal0=2
# and internal1=1.1
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '2.1E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '3.0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./f3]
order = CONSTANT
family = MONOMIAL
[../]
[./f4]
order = CONSTANT
family = MONOMIAL
[../]
[./f5]
order = CONSTANT
family = MONOMIAL
[../]
[./f6]
order = CONSTANT
family = MONOMIAL
[../]
[./f7]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[./int3]
order = CONSTANT
family = MONOMIAL
[../]
[./int4]
order = CONSTANT
family = MONOMIAL
[../]
[./int5]
order = CONSTANT
family = MONOMIAL
[../]
[./int6]
order = CONSTANT
family = MONOMIAL
[../]
[./int7]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./f3]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 3
variable = f3
[../]
[./f4]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 4
variable = f4
[../]
[./f5]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 5
variable = f5
[../]
[./f6]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 6
variable = f6
[../]
[./f7]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 7
variable = f7
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[./int3]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 3
variable = int3
[../]
[./int4]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 4
variable = int4
[../]
[./int5]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 5
variable = int5
[../]
[./int6]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 6
variable = int6
[../]
[./int7]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 7
variable = int7
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./f3]
type = PointValue
point = '0 0 0'
variable = f3
[../]
[./f4]
type = PointValue
point = '0 0 0'
variable = f4
[../]
[./f5]
type = PointValue
point = '0 0 0'
variable = f5
[../]
[./f6]
type = PointValue
point = '0 0 0'
variable = f6
[../]
[./f7]
type = PointValue
point = '0 0 0'
variable = f7
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[./int3]
type = PointValue
point = '0 0 0'
variable = int3
[../]
[./int4]
type = PointValue
point = '0 0 0'
variable = int4
[../]
[./int5]
type = PointValue
point = '0 0 0'
variable = int5
[../]
[./int6]
type = PointValue
point = '0 0 0'
variable = int6
[../]
[./int7]
type = PointValue
point = '0 0 0'
variable = int7
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 3
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple3]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1.1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple4]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1.1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple5]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 3.1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple6]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 2
strength = 3.1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple7]
type = TensorMechanicsPlasticSimpleTester
a = 2
b = 1
strength = 3.1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2 simple3 simple4 simple5 simple6 simple7'
deactivation_scheme = optimized_to_safe
max_NR_iterations = 4
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1 1'
debug_jac_at_intnl = '1 1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = eight_surface14
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/contact/test/tests/verification/hertz_cyl/half_symm_q8/hertz_cyl_half_1deg_template1.i)
[GlobalParams]
order = SECOND
volumetric_locking_correction = false
displacements = 'disp_x disp_y'
[]
[Mesh]
file = hertz_cyl_half_1deg.e
[]
[Problem]
type = ReferenceResidualProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./tang_force_x]
[../]
[./tang_force_y]
[../]
[]
[Functions]
[./disp_ramp_vert]
type = PiecewiseLinear
x = '0. 1. 3.5'
y = '0. -0.0020 -0.0020'
[../]
[./disp_ramp_horz]
type = PiecewiseLinear
x = '0. 1. 3.5'
y = '0. 0.0 0.0014'
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_end
boundary = 3
paired_boundary = 2
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_end
boundary = 3
paired_boundary = 2
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 3
paired_boundary = 2
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 3
paired_boundary = 2
[../]
[./tang_force_x]
type = PenetrationAux
variable = tang_force_x
quantity = tangential_force_x
boundary = 3
paired_boundary = 2
[../]
[./tang_force_y]
type = PenetrationAux
variable = tang_force_y
quantity = tangential_force_y
boundary = 3
paired_boundary = 2
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 3
paired_boundary = 2
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 4
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 4
[../]
[./disp_x639]
type = NodalVariableValue
nodeid = 638
variable = disp_x
[../]
[./disp_y639]
type = NodalVariableValue
nodeid = 638
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./side_x]
type = DirichletBC
variable = disp_y
boundary = '1 2'
value = 0.0
[../]
[./bot_y]
type = DirichletBC
variable = disp_x
boundary = '1 2'
value = 0.0
[../]
[./top_y_disp]
type = FunctionDirichletBC
variable = disp_y
boundary = 4
function = disp_ramp_vert
[../]
[./top_x_disp]
type = FunctionDirichletBC
variable = disp_x
boundary = 4
function = disp_ramp_horz
[../]
[]
[Materials]
[./stuff1_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e10
poissons_ratio = 0.0
[../]
[./stuff1_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./stuff1_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./stuff2_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff2_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./stuff2_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[./stuff3_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '3'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff3_strain]
type = ComputeFiniteStrain
block = '3'
[../]
[./stuff3_stress]
type = ComputeFiniteStrainElasticStress
block = '3'
[../]
[./stuff4_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '4'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff4_strain]
type = ComputeFiniteStrain
block = '4'
[../]
[./stuff4_stress]
type = ComputeFiniteStrainElasticStress
block = '4'
[../]
[./stuff5_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '5'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff5_strain]
type = ComputeFiniteStrain
block = '5'
[../]
[./stuff5_stress]
type = ComputeFiniteStrainElasticStress
block = '5'
[../]
[./stuff6_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '6'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff6_strain]
type = ComputeFiniteStrain
block = '6'
[../]
[./stuff6_stress]
type = ComputeFiniteStrainElasticStress
block = '6'
[../]
[./stuff7_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '7'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff7_strain]
type = ComputeFiniteStrain
block = '7'
[../]
[./stuff7_stress]
type = ComputeFiniteStrainElasticStress
block = '7'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-6
nl_rel_tol = 1e-5
l_max_its = 100
nl_max_its = 200
start_time = 0.0
end_time = 3.5
l_tol = 1e-3
dt = 0.1
dtmin = 0.1
[]
[Preconditioning]
[./SMP]
type = SMP
full = true
[../]
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '3 4'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '3 4'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
show = 'x_disp y_disp cont_press'
start_time = 0.9
execute_vector_postprocessors_on = timestep_end
[../]
[./chkfile2]
type = CSV
show = 'bot_react_x bot_react_y disp_x639 disp_y639 top_react_x top_react_y'
start_time = 0.9
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./interface]
primary = 2
secondary = 3
normalize_penalty = true
tangential_tolerance = 1e-3
penalty = 1e+10
[../]
[]
(modules/tensor_mechanics/test/tests/multi/two_surface02.i)
# Plasticit models:
# SimpleTester with a = 0 and b = 1 and strength = 1
# SimpleTester with a = 1 and b = 1 and strength = 2
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 1.5E-6m in the y z directions.
# trial stress_zz = 1.5 and stress_yy = 1.5
#
# Then both SimpleTesters should activate, and the final stress
# should have have stress_zz = 1 = stress_yy (ie, the "corner" point)
# the plastic strain for SimpleTester1 should be zero
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1.5E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1.5E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[]
[UserObjects]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 2
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = two_surface02
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/contact/test/tests/verification/patch_tests/brick_4/brick4_template2.i)
[GlobalParams]
order = SECOND
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
file = brick4_mesh.e
[]
[Problem]
type = AugmentedLagrangianContactProblem
maximum_lagrangian_update_iterations = 200
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./penetration]
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./saved_z]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./diag_saved_z]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./inc_slip_z]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./accum_slip_z]
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y saved_z'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 4
paired_boundary = 3
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./ref_resid_x]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_x
[../]
[./ref_resid_y]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_y
[../]
[./sigma_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./sigma_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./disp_x59]
type = NodalVariableValue
nodeid = 58
variable = disp_x
[../]
[./disp_x64]
type = NodalVariableValue
nodeid = 63
variable = disp_x
[../]
[./disp_y59]
type = NodalVariableValue
nodeid = 58
variable = disp_y
[../]
[./disp_y64]
type = NodalVariableValue
nodeid = 63
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./bot_y]
type = DirichletBC
variable = disp_y
boundary = 1
value = 0.0
[../]
[./side_x]
type = DirichletBC
variable = disp_x
boundary = 2
value = 0.0
[../]
[./back_z]
type = DirichletBC
variable = disp_z
boundary = 6
value = 0.0
[../]
[./top_press]
type = Pressure
variable = disp_y
boundary = 5
factor = 109.89
[../]
[]
[Materials]
[./bot_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./bot_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./bot_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./top_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./top_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./top_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-7
nl_rel_tol = 1e-6
l_max_its = 50
nl_max_its = 100
dt = 1.0
end_time = 1.0
num_steps = 10
dtmin = 1.0
l_tol = 1e-4
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '1 3 4 5'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '1 3 4 5'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
show = 'bot_react_x bot_react_y disp_x59 disp_y59 disp_x64 disp_y64 stress_yy stress_zz top_react_x top_react_y x_disp y_disp cont_press'
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./leftright]
secondary = 3
primary = 4
normalize_penalty = true
tangential_tolerance = 1e-3
penalty = 1e+9
al_penetration_tolerance = 1e-8
[../]
[]
(modules/tensor_mechanics/test/tests/multi/three_surface11.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 3
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 0E-6m in y direction and 2E-6 in z direction.
# trial stress_yy = 0 and stress_zz = 2.0
#
# Then SimpleTester0 should activate and the algorithm will return to
# stress_zz=1
# internal0 should be 1.0
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0.0E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '2.0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 3
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface11
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/multi/three_surface03.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 1.5
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 0.5E-6m in y direction and 2.0E-6 in z direction.
# trial stress_yy = 0.5 and stress_zz = 2.0
#
# Then SimpleTester0 and SimpleTester2 should activate and the algorithm will return to
# the corner stress_yy=0.5, stress_zz=1
# internal0 should be 1.0, and others zero
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0.5E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '2.0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 1.5
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface03
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/j2_plasticity/small_deform1.i)
# UserObject J2 test
# apply uniform stretch in x, y and z directions.
# no plasticity should be observed
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '1E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = f
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = f
[../]
[./iter]
type = PointValue
point = '0 0 0'
variable = iter
[../]
[]
[UserObjects]
[./str]
type = TensorMechanicsHardeningConstant
value = 1
[../]
[./j2]
type = TensorMechanicsPlasticJ2
yield_strength = str
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = j2
debug_fspb = crash
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = small_deform1
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/fileread.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'ux uy uz'
[]
[Variables]
[./ux]
[../]
[./uy]
[../]
[./uz]
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./rotout]
order = CONSTANT
family = MONOMIAL
[../]
[./e_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./gss]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'ux uy uz'
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./e_zz]
type = RankTwoAux
variable = e_zz
rank_two_tensor = lage
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./gss]
type = MaterialStdVectorAux
variable = gss
property = state_var_gss
index = 0
execute_on = timestep_end
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = uy
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = ux
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = uz
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = uz
boundary = front
function = tdisp
[../]
[]
[UserObjects]
[./slip_rate_gss]
type = CrystalPlasticitySlipRateGSS
variable_size = 12
slip_sys_file_name = input_slip_sys.txt
num_slip_sys_flowrate_props = 2
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
uo_state_var_name = state_var_gss
[../]
[./slip_resistance_gss]
type = CrystalPlasticitySlipResistanceGSS
variable_size = 12
uo_state_var_name = state_var_gss
[../]
[./state_var_gss]
type = CrystalPlasticityStateVariable
variable_size = 12
intvar_read_type = file_input
state_variable_file_name = input_state_variable.txt
uo_state_var_evol_rate_comp_name = state_var_evol_rate_comp_gss
scale_factor = 1.0
[../]
[./state_var_evol_rate_comp_gss]
type = CrystalPlasticityStateVarRateComponentGSS
variable_size = 12
hprops = '1.0 541.5 109.8 2.5'
uo_slip_rate_name = slip_rate_gss
uo_state_var_name = state_var_gss
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainUObasedCP
stol = 1e-2
tan_mod_type = exact
uo_slip_rates = 'slip_rate_gss'
uo_slip_resistances = 'slip_resistance_gss'
uo_state_vars = 'state_var_gss'
uo_state_var_evol_rate_comps = 'state_var_evol_rate_comp_gss'
[../]
[./strain]
type = ComputeFiniteStrain
displacements = 'ux uy uz'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
[../]
[./e_zz]
type = ElementAverageValue
variable = e_zz
[../]
[./gss]
type = ElementAverageValue
variable = gss
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.05
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
nl_abs_tol = 1e-10
nl_rel_step_tol = 1e-10
dtmax = 10.0
nl_rel_tol = 1e-10
end_time = 1
dtmin = 0.05
num_steps = 10
nl_abs_step_tol = 1e-10
[]
[Outputs]
exodus = true
[]
(modules/contact/test/tests/verification/hertz_cyl/half_symm_q8/hertz_cyl_half_1deg_template3.i)
[GlobalParams]
order = SECOND
volumetric_locking_correction = false
displacements = 'disp_x disp_y'
[]
[Mesh]
file = hertz_cyl_half_1deg.e
[]
[Problem]
type = ReferenceResidualProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./tang_force_x]
[../]
[./tang_force_y]
[../]
[]
[Functions]
[./disp_ramp_vert]
type = PiecewiseLinear
x = '0. 1. 11.'
y = '0. -0.0020 -0.0020'
[../]
[./disp_ramp_horz]
type = PiecewiseLinear
x = '0. 1. 11.'
y = '0. 0.0 0.0014'
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_end
boundary = 3
paired_boundary = 2
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_end
boundary = 3
paired_boundary = 2
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 3
paired_boundary = 2
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 3
paired_boundary = 2
[../]
[./tang_force_x]
type = PenetrationAux
variable = tang_force_x
quantity = tangential_force_x
boundary = 3
paired_boundary = 2
[../]
[./tang_force_y]
type = PenetrationAux
variable = tang_force_y
quantity = tangential_force_y
boundary = 3
paired_boundary = 2
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 3
paired_boundary = 2
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 4
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 4
[../]
[./disp_x639]
type = NodalVariableValue
nodeid = 638
variable = disp_x
[../]
[./disp_y639]
type = NodalVariableValue
nodeid = 638
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./side_x]
type = DirichletBC
variable = disp_y
boundary = '1 2'
value = 0.0
[../]
[./bot_y]
type = DirichletBC
variable = disp_x
boundary = '1 2'
value = 0.0
[../]
[./top_y_disp]
type = FunctionDirichletBC
variable = disp_y
boundary = 4
function = disp_ramp_vert
[../]
[./top_x_disp]
type = FunctionDirichletBC
variable = disp_x
boundary = 4
function = disp_ramp_horz
[../]
[]
[Materials]
[./stuff1_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e10
poissons_ratio = 0.0
[../]
[./stuff1_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./stuff1_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./stuff2_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff2_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./stuff2_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[./stuff3_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '3'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff3_strain]
type = ComputeFiniteStrain
block = '3'
[../]
[./stuff3_stress]
type = ComputeFiniteStrainElasticStress
block = '3'
[../]
[./stuff4_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '4'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff4_strain]
type = ComputeFiniteStrain
block = '4'
[../]
[./stuff4_stress]
type = ComputeFiniteStrainElasticStress
block = '4'
[../]
[./stuff5_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '5'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff5_strain]
type = ComputeFiniteStrain
block = '5'
[../]
[./stuff5_stress]
type = ComputeFiniteStrainElasticStress
block = '5'
[../]
[./stuff6_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '6'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff6_strain]
type = ComputeFiniteStrain
block = '6'
[../]
[./stuff6_stress]
type = ComputeFiniteStrainElasticStress
block = '6'
[../]
[./stuff7_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '7'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff7_strain]
type = ComputeFiniteStrain
block = '7'
[../]
[./stuff7_stress]
type = ComputeFiniteStrainElasticStress
block = '7'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-7
nl_rel_tol = 1e-6
l_max_its = 100
nl_max_its = 200
start_time = 0.0
end_time = 2.0
l_tol = 5e-4
dt = 0.1
dtmin = 0.1
[]
[Preconditioning]
[./SMP]
type = SMP
full = true
[../]
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '3 4'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '3 4'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
show = 'x_disp y_disp cont_press'
start_time = 0.9
execute_vector_postprocessors_on = timestep_end
[../]
[./chkfile2]
type = CSV
show = 'bot_react_x bot_react_y disp_x639 disp_y639 top_react_x top_react_y'
start_time = 0.9
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./interface]
primary = 2
secondary = 3
model = coulomb
friction_coefficient = 0.0
formulation = penalty
normalize_penalty = true
tangential_tolerance = 1e-3
penalty = 1e+9
[../]
[]
[Dampers]
[./contact_slip]
type = ContactSlipDamper
primary = '2'
secondary = '3'
[../]
[]
(modules/tensor_mechanics/test/tests/multi/three_surface12.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 3
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 1.5E-6m in y direction and 1.5E-6 in z direction.
# trial stress_yy = .15 and stress_zz = 1.5
#
# Then SimpleTester0 and SimpleTester1 should activate and the algorithm will return to
# stress_zz=1=stress_yy
# internal0 should be 0.5 and internal1 should be 0.5
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1.5E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1.5E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 3
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface12
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/prop_block_read.i)
[Mesh]
[gen]
type = GeneratedMeshGenerator
dim = 2
xmin = 0
ymin = 0
xmax = 1
ymax = 1
nx = 2
ny = 2
elem_type = QUAD4
[]
[./subdomain_id]
input = gen
type = ElementSubdomainIDGenerator
subdomain_ids = '0 1
0 1'
[../]
displacements = 'disp_x disp_y'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[]
[GlobalParams]
volumetric_locking_correction = true
[]
[AuxVariables]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./e_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./fp_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./gss]
order = CONSTANT
family = MONOMIAL
[../]
[./euler1]
order = CONSTANT
family = MONOMIAL
[../]
[./euler2]
order = CONSTANT
family = MONOMIAL
[../]
[./euler3]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[UserObjects]
[./prop_read]
type = PropertyReadFile
prop_file_name = 'euler_ang_file.txt'
# Enter file data as prop#1, prop#2, .., prop#nprop
nprop = 3
read_type = block
nblock= 2
[../]
[]
[AuxKernels]
[./stress_yy]
type = RankTwoAux
variable = stress_yy
rank_two_tensor = stress
index_j = 1
index_i = 1
execute_on = timestep_end
[../]
[./e_yy]
type = RankTwoAux
variable = e_yy
rank_two_tensor = lage
index_j = 1
index_i = 1
execute_on = timestep_end
[../]
[./fp_yy]
type = RankTwoAux
variable = fp_yy
rank_two_tensor = fp
index_j = 1
index_i = 1
execute_on = timestep_end
[../]
[./gss]
type = MaterialStdVectorAux
variable = gss
property = state_var_gss
index = 0
execute_on = timestep_end
[../]
[./euler1]
type = MaterialRealVectorValueAux
variable = euler1
property = Euler_angles
component = 0
execute_on = timestep_end
[../]
[./euler2]
type = MaterialRealVectorValueAux
variable = euler2
property = Euler_angles
component = 1
execute_on = timestep_end
[../]
[./euler3]
type = MaterialRealVectorValueAux
variable = euler3
property = Euler_angles
component = 2
execute_on = timestep_end
[../]
[]
[BCs]
[./fix_x]
type = DirichletBC
variable = disp_x
boundary = 'left'
value = 0
[../]
[./fix_y]
type = DirichletBC
variable = disp_y
boundary = 'bottom'
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_y
boundary = top
function = tdisp
[../]
[]
[UserObjects]
[./slip_rate_gss]
type = CrystalPlasticitySlipRateGSS
variable_size = 12
slip_sys_file_name = input_slip_sys.txt
num_slip_sys_flowrate_props = 2
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
uo_state_var_name = state_var_gss
[../]
[./slip_resistance_gss]
type = CrystalPlasticitySlipResistanceGSS
variable_size = 12
uo_state_var_name = state_var_gss
[../]
[./state_var_gss]
type = CrystalPlasticityStateVariable
variable_size = 12
groups = '0 4 8 12'
group_values = '60.8 60.8 60.8'
uo_state_var_evol_rate_comp_name = state_var_evol_rate_comp_gss
scale_factor = 1.0
[../]
[./state_var_evol_rate_comp_gss]
type = CrystalPlasticityStateVarRateComponentGSS
variable_size = 12
hprops = '1.0 541.5 109.8 2.5'
uo_slip_rate_name = slip_rate_gss
uo_state_var_name = state_var_gss
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainUObasedCP
stol = 1e-2
tan_mod_type = exact
uo_slip_rates = 'slip_rate_gss'
uo_slip_resistances = 'slip_resistance_gss'
uo_state_vars = 'state_var_gss'
uo_state_var_evol_rate_comps = 'state_var_evol_rate_comp_gss'
[../]
[./strain]
type = ComputeFiniteStrain
displacements = 'disp_x disp_y'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
read_prop_user_object = prop_read
[../]
[]
[Postprocessors]
[./stress_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./e_yy]
type = ElementAverageValue
variable = e_yy
[../]
[./fp_yy]
type = ElementAverageValue
variable = fp_yy
[../]
[./gss]
type = ElementAverageValue
variable = gss
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.01
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
nl_abs_tol = 1e-10
nl_rel_step_tol = 1e-10
dtmax = 10.0
nl_rel_tol = 1e-10
end_time = 1
dtmin = 0.01
num_steps = 10
nl_abs_step_tol = 1e-10
[]
[Outputs]
exodus = true
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y'
use_displaced_mesh = true
[../]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform_hard1.i)
# apply uniform stretches in x, y and z directions.
# let mc_cohesion = 10, mc_cohesion_residual = 2, mc_cohesion_rate =
# With cohesion = C, friction_angle = 60deg, tip_smoother = 4, the
# algorithm should return to
# sigma_m = (C*Cos(60) - 4)/Sin(60)
# This allows checking of the relationship for C
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '1E-6*x*t'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1E-6*y*t'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z*t'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./mc_int]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./mc_int_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_internal_parameter
variable = mc_int
[../]
[./yield_fcn_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./internal]
type = PointValue
point = '0 0 0'
variable = mc_int
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = yield_fcn
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningExponential
value_0 = 10
value_residual = 2
rate = 1E4
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 60
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 5
convert_to_radians = true
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 4
mc_edge_smoother = 25
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = mc
debug_fspb = crash
debug_jac_at_stress = '10 1 2 1 10 3 2 3 10'
debug_jac_at_pm = 1
debug_jac_at_intnl = 1E-4
debug_stress_change = 1E-5
debug_pm_change = 1E-6
debug_intnl_change = 1E-8
[../]
[]
[Executioner]
end_time = 10
dt = 1
type = Transient
[]
[Outputs]
file_base = small_deform_hard1
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/multi/four_surface14.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 3
# SimpleTester3 with a = 0 and b = 1 and strength = 1.1
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 2.1E-6m in y direction and 3E-6 in z direction.
# trial stress_yy = 2.1 and stress_zz = 3.0
#
# This is similar to three_surface14.i, and a description is found there.
# The result should be stress_zz=1=stress_yy, with internal0=2
# and internal1=1.1
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '2.1E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '3.0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./f3]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[./int3]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./f3]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 3
variable = f3
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[./int3]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 3
variable = int3
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./f3]
type = PointValue
point = '0 0 0'
variable = f3
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[./int3]
type = PointValue
point = '0 0 0'
variable = int3
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 3
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple3]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1.1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2 simple3'
max_NR_iterations = 4
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1 1'
debug_jac_at_intnl = '1 1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = four_surface14
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/elem_prop_read_user_object/prop_grain_read_3d.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'disp_x disp_y disp_z'
nx = 30
ny = 30
nz = 30
[]
[Variables]
[./disp_x]
block = 0
[../]
[./disp_y]
block = 0
[../]
[./disp_z]
block = 0
[../]
[]
[AuxVariables]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./e_yy]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.05*t
[../]
[]
[UserObjects]
[./prop_read]
type = PropertyReadFile
prop_file_name = 'input_file.txt'
nprop = 4
read_type = grain
ngrain = 4
[../]
[]
[AuxKernels]
[./stress_yy]
type = RankTwoAux
variable = stress_yy
rank_two_tensor = stress
index_j = 1
index_i = 1
execute_on = timestep_end
block = 0
[../]
[./e_yy]
type = RankTwoAux
variable = e_yy
rank_two_tensor = elastic_strain
index_j = 1
index_i = 1
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./fix_x]
type = DirichletBC
variable = disp_x
boundary = 'left'
value = 0
[../]
[./fix_y]
type = DirichletBC
variable = disp_y
boundary = 'bottom'
value = 0
[../]
[./fix_z]
type = DirichletBC
variable = disp_z
boundary = 'back'
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_y
boundary = top
function = tdisp
[../]
[]
[Materials]
[./elasticity_tensor_with_Euler]
type = ComputeElasticityTensorCP
block = 0
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
read_prop_user_object = prop_read
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./stress]
type = ComputeFiniteStrainElasticStress
block = 0
[../]
[]
[Postprocessors]
[./stress_yy]
type = ElementAverageValue
variable = stress_yy
block = 'ANY_BLOCK_ID 0'
[../]
[./e_yy]
type = ElementAverageValue
variable = e_yy
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.05
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
nl_abs_tol = 1e-10
nl_rel_step_tol = 1e-10
dtmax = 10.0
nl_rel_tol = 1e-10
end_time = 1
dtmin = 0.05
num_steps = 2
nl_abs_step_tol = 1e-10
[]
[Outputs]
file_base = prop_grain_read_3d_out
exodus = true
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
use_displaced_mesh = true
[../]
[]
(modules/tensor_mechanics/test/tests/multi/two_surface01.i)
# Plasticit models:
# SimpleTester with a = 0 and b = 1 and strength = 1
# SimpleTester with a = 1 and b = 1 and strength = 2
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 1.5E-6m in the z directions.
# stress_zz = 1.5
#
# Then only the first SimpleTester should activate, and the final stress
# should have have only nonzero component stress_zz = 1
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1.5E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[]
[UserObjects]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 2
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = two_surface01
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/multi/three_surface07.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 1.5
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 1.5E-6m in y direction and 0.8E-6 in z direction.
# trial stress_yy = 1.5 and stress_zz = 0.8
#
# Then SimpleTester1 and SimpleTester2 should activate and the algorithm will return to
# the corner stress_yy=1.0, stress_zz=0.5
# internal1 should be 0.2, and internal2 should be 0.3
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1.5E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0.8E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 1.5
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface07
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform2.i)
# apply repeated stretches in x, y and z directions, so that mean_stress = 0
# This maps out the yield surface in the octahedral plane for zero mean stress
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '2E-6*x*sin(t)'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '2E-6*y*sin(2*t)'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '-2E-6*z*(sin(t)+sin(2*t))'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./yield_fcn_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = yield_fcn
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = yield_fcn
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = yield_fcn
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 10
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 20
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 0
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 4
mc_edge_smoother = 20
yield_function_tolerance = 1E-3
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = mc
debug_fspb = crash
[../]
[]
[Executioner]
end_time = 100
dt = 1
type = Transient
[]
[Outputs]
file_base = small_deform2
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform_hard3.i)
# apply repeated stretches in x z directions, and smaller stretches along the y direction,
# so that sigma_I = sigma_II,
# which means that lode angle = 30deg.
# The allows yield surface in meridional plane to be mapped out
#
# friction_angle = 50deg, friction_angle_residual=51deg, friction_angle_rate = 1E7 (huge)
# cohesion = 10, cohesion_residual = 9.9, cohesion_rate = 1E7 (huge)
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '1E-6*x*t'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0.25E-6*y*sin(t)'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z*t'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./mc_int]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./mc_int_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_internal_parameter
variable = mc_int
[../]
[./yield_fcn_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./internal]
type = PointValue
point = '0 0 0'
variable = mc_int
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = yield_fcn
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningExponential
value_0 = 10
value_residual = 9.9
rate = 1E7
[../]
[./mc_phi]
type = TensorMechanicsHardeningExponential
value_0 = 0.8726646 # 50deg
value_residual = 0.8901179 # 51deg
rate = 1E7
[../]
[./mc_psi]
type = TensorMechanicsHardeningExponential
value_0 = 0
value_residual = 0.8726646 # 50deg
rate = 3000
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 4
mc_edge_smoother = 20
yield_function_tolerance = 1E-6
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = mc
debug_fspb = crash
debug_jac_at_stress = '10 1 2 1 11 -3 2 -3 8'
debug_jac_at_pm = 1
debug_jac_at_intnl = 1
debug_stress_change = 1E-5
debug_pm_change = 1E-6
debug_intnl_change = 1E-6
[../]
[]
[Executioner]
end_time = 30
dt = 1
type = Transient
[]
[Outputs]
file_base = small_deform_hard3
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/planar_hard2.i)
# apply uniform stretches in x, y and z directions.
# let friction_angle = 60deg, friction_angle_residual=10deg, friction_angle_rate = 0.5E4
# With cohesion = C, friction_angle = phi, the
# algorithm should return to
# sigma_m = C*Cos(phi)/Sin(phi)
# Or, when T=C,
# phi = arctan(C/sigma_m)
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '1E-6*x*t'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1E-6*y*t'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z*t'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./mc_int]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./mc_int_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_internal_parameter
variable = mc_int
[../]
[./yield_fcn_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./internal]
type = PointValue
point = '0 0 0'
variable = mc_int
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = yield_fcn
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 10
[../]
[./mc_phi]
type = TensorMechanicsHardeningExponential
value_0 = 1.04719755 # 60deg
value_residual = 0.17453293 # 10deg
rate = 0.5E4
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 5
convert_to_radians = true
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulombMulti
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
shift = 1E-12
use_custom_returnMap = true
yield_function_tolerance = 1E-5
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0.0E7 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-12
plastic_models = mc
[../]
[]
[Executioner]
end_time = 10
dt = 1
type = Transient
[]
[Outputs]
file_base = planar_hard2
exodus = false
[./csv]
type = CSV
execute_on = timestep_end
[../]
[]
(modules/tensor_mechanics/test/tests/multi/three_surface21.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 1.5
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 2.0E-6m in y direction and 2.0E-6 in z direction.
# trial stress_yy = 2.0 and stress_zz = 2.0
#
# Then all yield functions will activate
# However, there is linear dependence. SimpleTester1 or SimpleTester0 will be rutned off (they are equi-distant).
# The algorithm will return to one corner point, but there will be negative plastic multipliers
# so the other SimpleTester0 or SimpleTester1 will turn off, and the algorithm will return to
# stress_yy=0.75 and stress_zz=0.75
# internal2=1.25
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '2.0E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '2.0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 1.5
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface21
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/contact/test/tests/mortar_dynamics/block-dynamics-action.i)
starting_point = 2e-1
offset = -0.19
[GlobalParams]
displacements = 'disp_x disp_y'
[]
[Mesh]
[file]
type = FileMeshGenerator
file = long-bottom-block-no-lower-d.e
[]
[]
[Variables]
[disp_x]
block = '1 2'
[]
[disp_y]
block = '1 2'
[]
[]
[ICs]
[disp_y]
block = 2
variable = disp_y
value = '${fparse starting_point + offset}'
type = ConstantIC
[]
[]
[Kernels]
[DynamicTensorMechanics]
displacements = 'disp_x disp_y'
generate_output = 'stress_xx stress_yy'
strain = FINITE
block = '1 2'
stiffness_damping_coefficient = 1.0
hht_alpha = 0.0
[]
[inertia_x]
type = InertialForce
variable = disp_x
velocity = vel_x
acceleration = accel_x
beta = 0.25
gamma = 0.5
alpha = 0
eta = 0.0
block = '1 2'
[]
[inertia_y]
type = InertialForce
variable = disp_y
velocity = vel_y
acceleration = accel_y
beta = 0.25
gamma = 0.5
alpha = 0
eta = 0.0
block = '1 2'
[]
[]
[Materials]
[elasticity_2]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[]
[elasticity_1]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e8
poissons_ratio = 0.3
[]
[stress]
type = ComputeFiniteStrainElasticStress
block = '1 2'
[]
[strain]
type = ComputeFiniteStrain
block = '1 2'
[]
[density]
type = GenericConstantMaterial
block = '1 2'
prop_names = 'density'
prop_values = '7750'
[]
[]
[AuxVariables]
[vel_x]
block = '1 2'
[]
[accel_x]
block = '1 2'
[]
[vel_y]
block = '1 2'
[]
[accel_y]
block = '1 2'
[]
[vel_z]
block = '1 2'
[]
[accel_z]
block = '1 2'
[]
[]
[AuxKernels]
[accel_x]
type = NewmarkAccelAux
variable = accel_x
displacement = disp_x
velocity = vel_x
beta = 0.25
execute_on = 'LINEAR timestep_end'
[]
[vel_x]
type = NewmarkVelAux
variable = vel_x
acceleration = accel_x
gamma = 0.5
execute_on = 'LINEAR timestep_end'
[]
[accel_y]
type = NewmarkAccelAux
variable = accel_y
displacement = disp_y
velocity = vel_y
beta = 0.25
execute_on = 'LINEAR timestep_end'
[]
[vel_y]
type = NewmarkVelAux
variable = vel_y
acceleration = accel_y
gamma = 0.5
execute_on = 'LINEAR timestep_end'
[]
[]
[Contact]
[mechanical]
primary = 20
secondary = 10
formulation = mortar
model = frictionless
c_normal = 1e4
interpolate_normals = false
capture_tolerance = 1.0e-5
[]
[]
[BCs]
[botx]
type = DirichletBC
variable = disp_x
boundary = 40
value = 0.0
[]
[boty]
type = DirichletBC
variable = disp_y
boundary = 40
value = 0.0
[]
[topy]
type = FunctionDirichletBC
variable = disp_y
boundary = 30
function = '${starting_point} * cos(2 * pi / 4 * t) + ${offset}'
[]
[leftx]
type = FunctionDirichletBC
variable = disp_x
boundary = 50
function = '1e-2 * t'
[]
[]
[Executioner]
type = Transient
end_time = 75
dt = 0.05
dtmin = .05
solve_type = 'PJFNK'
petsc_options = '-snes_converged_reason -ksp_converged_reason -pc_svd_monitor '
'-snes_linesearch_monitor -snes_ksp_ew'
petsc_options_iname = '-pc_type -pc_factor_shift_type -pc_factor_shift_amount -mat_mffd_err '
petsc_options_value = 'lu NONZERO 1e-15 1e-5'
nl_max_its = 20
line_search = 'none'
snesmf_reuse_base = false
[TimeIntegrator]
type = NewmarkBeta
beta = 0.25
gamma = 0.5
[]
[]
[Debug]
show_var_residual_norms = true
[]
[Outputs]
exodus = true
checkpoint = true
[]
[Preconditioning]
[smp]
type = SMP
full = true
[]
[]
[Postprocessors]
active = ''
[num_nl]
type = NumNonlinearIterations
[]
[cumulative]
type = CumulativeValuePostprocessor
postprocessor = num_nl
[]
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/cp_slip_rate_integ/crysp_linesearch.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'disp_x disp_y disp_z'
[]
[Variables]
[./disp_x]
block = 0
[../]
[./disp_y]
block = 0
[../]
[./disp_z]
block = 0
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./e_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./gss1]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.0001*t
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./e_zz]
type = RankTwoAux
variable = e_zz
rank_two_tensor = lage
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./gss1]
type = MaterialStdVectorAux
variable = gss1
property = gss
index = 0
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = disp_y
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = disp_x
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = disp_z
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = disp_z
boundary = front
function = tdisp
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainCPSlipRateRes
block = 0
slip_sys_file_name = input_slip_sys.txt
nss = 12
num_slip_sys_flowrate_props = 2 #Number of properties in a slip system
flowprops = '1 4 0.001 0.01 5 8 0.001 0.01 9 12 0.001 0.01'
hprops = '1.0 541.5 60.8 109.8 2.5'
gprops = '1 4 60.8 5 8 60.8 9 12 60.8'
tan_mod_type = exact
slip_incr_tol = 1
maximum_substep_iteration = 12
use_line_search = true
rtol = 1e-8
abs_tol = 1e-12
line_search_method = 'BISECTION'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
block = 0
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./e_zz]
type = ElementAverageValue
variable = e_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./gss1]
type = ElementAverageValue
variable = gss1
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type'
petsc_options_value = 'lu'
nl_rel_tol = 1e-10
nl_abs_tol = 1e-10
dt = 10
dtmin = 0.05
dtmax = 1e4
num_steps = 10
[]
[Outputs]
file_base = crysp_linesearch_out
exodus = true
print_linear_residuals = true
perf_graph = true
[]
(modules/tensor_mechanics/test/tests/jacobian_damper/cube_load.i)
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
displacements = 'disp_x disp_y disp_z'
# This test uses ElementalVariableValue postprocessors on specific
# elements, so element numbering needs to stay unchanged
allow_renumbering = false
[]
[Variables]
[./disp_x]
order = FIRST
family = LAGRANGE
[../]
[./disp_y]
order = FIRST
family = LAGRANGE
[../]
[./disp_z]
order = FIRST
family = LAGRANGE
[../]
[]
[AuxVariables]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./total_strain_yy]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Functions]
[./top_pull]
type = PiecewiseLinear
x = '0 1 2'
y = '0 0.025 0.05'
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./total_strain_yy]
type = RankTwoAux
rank_two_tensor = total_strain
variable = total_strain_yy
index_i = 1
index_j = 1
[../]
[]
[BCs]
[./y_pull_function]
type = FunctionDirichletBC
variable = disp_y
boundary = 3
function = top_pull
[../]
[./x_bot]
type = DirichletBC
variable = disp_x
boundary = 4
value = 0.0
[../]
[./y_bot]
type = DirichletBC
variable = disp_y
boundary = 1
value = 0.0
[../]
[./z_bot]
type = DirichletBC
variable = disp_z
boundary = 0
value = 0.0
[../]
[]
[Postprocessors]
[./stress_yy_el]
type = ElementalVariableValue
variable = stress_yy
elementid = 0
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeIsotropicElasticityTensor
poissons_ratio = 0.3
youngs_modulus = 2e5
[../]
[./strain]
type = ComputeFiniteStrain
displacements = 'disp_x disp_y disp_z'
[../]
[./stress]
type = ComputeFiniteStrainElasticStress
[../]
[]
[Dampers]
[./disp_x_damp]
type = ElementJacobianDamper
max_increment = 0.002
displacements = 'disp_x disp_y disp_z'
[../]
[]
[Executioner]
type = Transient
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options = '-snes_ksp_ew'
petsc_options_iname = '-ksp_gmres_restart -pc_type -pc_hypre_type -pc_hypre_boomeramg_max_iter'
petsc_options_value = '201 hypre boomeramg 4'
line_search = 'none'
l_max_its = 100
nl_max_its = 100
nl_rel_tol = 1e-12
nl_abs_tol = 1e-10
l_tol = 1e-9
start_time = 0.0
end_time = 2
dt = 1
[]
[Outputs]
exodus = true
[]
(modules/tensor_mechanics/test/tests/multi/three_surface13.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 3
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 2.0E-6m in y direction and 0E-6 in z direction.
# trial stress_yy = 2 and stress_zz = 0
#
# Then SimpleTester1 should activate and the algorithm will return to
# stress_yy=1
# internal1 should be 1
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '2.0E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0.0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 3
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface13
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/hyperelastic_viscoplastic/one_elem_multi.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'ux uy uz'
[]
[Variables]
[./ux]
block = 0
[../]
[./uy]
block = 0
[../]
[./uz]
block = 0
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'ux uy uz'
use_displaced_mesh = true
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./peeq_soft]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./peeq_hard]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./peeq_soft]
type = MaterialRealAux
variable = peeq_soft
property = ep_eqv1
execute_on = timestep_end
block = 0
[../]
[./peeq_hard]
type = MaterialRealAux
variable = peeq_hard
property = ep_eqv2
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = uy
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = ux
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = uz
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = uz
boundary = front
function = '0.01*t'
[../]
[]
[UserObjects]
[./flowstress1]
type = HEVPRambergOsgoodHardening
yield_stress = 100
hardening_exponent = 0.1
reference_plastic_strain = 0.002
intvar_prop_name = ep_eqv1
[../]
[./flowstress2]
type = HEVPRambergOsgoodHardening
yield_stress = 100
hardening_exponent = 0.3
reference_plastic_strain = 0.002
intvar_prop_name = ep_eqv2
[../]
[./flowrate1]
type = HEVPFlowRatePowerLawJ2
reference_flow_rate = 0.0001
flow_rate_exponent = 50.0
flow_rate_tol = 1
strength_prop_name = flowstress1
[../]
[./flowrate2]
type = HEVPFlowRatePowerLawJ2
reference_flow_rate = 0.0001
flow_rate_exponent = 50.0
flow_rate_tol = 1
strength_prop_name = flowstress2
[../]
[./ep_eqv1]
type = HEVPEqvPlasticStrain
intvar_rate_prop_name = ep_eqv_rate1
[../]
[./ep_eqv_rate1]
type = HEVPEqvPlasticStrainRate
flow_rate_prop_name = flowrate1
[../]
[./ep_eqv2]
type = HEVPEqvPlasticStrain
intvar_rate_prop_name = ep_eqv_rate2
[../]
[./ep_eqv_rate2]
type = HEVPEqvPlasticStrainRate
flow_rate_prop_name = flowrate2
[../]
[]
[Materials]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'ux uy uz'
[../]
[./viscop]
type = FiniteStrainHyperElasticViscoPlastic
block = 0
resid_abs_tol = 1e-18
resid_rel_tol = 1e-8
maxiters = 50
max_substep_iteration = 5
flow_rate_user_objects = 'flowrate1 flowrate2'
strength_user_objects = 'flowstress1 flowstress2'
internal_var_user_objects = 'ep_eqv1 ep_eqv2'
internal_var_rate_user_objects = 'ep_eqv_rate1 ep_eqv_rate2'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
C_ijkl = '2.8e5 1.2e5 1.2e5 2.8e5 1.2e5 2.8e5 0.8e5 0.8e5 0.8e5'
fill_method = symmetric9
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./peeq_soft]
type = ElementAverageValue
variable = peeq_soft
block = 'ANY_BLOCK_ID 0'
[../]
[./peeq_hard]
type = ElementAverageValue
variable = peeq_hard
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.02
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
dtmax = 10.0
nl_rel_tol = 1e-10
dtmin = 0.02
num_steps = 10
[]
[Outputs]
file_base = one_elem_multi
exodus = true
csv = false
[]
(modules/tensor_mechanics/test/tests/multi/paper3.i)
# This runs the third example models described in the 'MultiSurface' plasticity paper
# Just change the deactivation_scheme
#
# Plasticity models:
# Mohr-Coulomb with cohesion = 40MPa, friction angle = 35deg, dilation angle = 5deg
# Tensile with strength = 1MPa
# WeakPlaneTensile with strength = 1000Pa
# WeakPlaneShear with cohesion = 0.1MPa and friction angle = 25, dilation angle = 5deg
#
# Lame lambda = 1.2GPa. Lame mu = 1.2GPa (Young = 3GPa, poisson = 0.5)
#
# A line of elements is perturbed randomly, and return to the yield surface at each quadpoint is checked
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1000
ny = 125
nz = 1
xmin = 0
xmax = 1000
ymin = 0
ymax = 125
zmin = 0
zmax = 1
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[GlobalParams]
volumetric_locking_correction=true
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[ICs]
[./x]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_x
[../]
[./y]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_y
[../]
[./z]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_z
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./linesearch]
order = CONSTANT
family = MONOMIAL
[../]
[./ld]
order = CONSTANT
family = MONOMIAL
[../]
[./constr_added]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./linesearch]
type = MaterialRealAux
property = plastic_linesearch_needed
variable = linesearch
[../]
[./ld]
type = MaterialRealAux
property = plastic_linear_dependence_encountered
variable = ld
[../]
[./constr_added]
type = MaterialRealAux
property = plastic_constraints_added
variable = constr_added
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./max_iter]
type = ElementExtremeValue
variable = iter
outputs = console
[../]
[./av_iter]
type = ElementAverageValue
variable = iter
outputs = 'console csv'
[../]
[./av_linesearch]
type = ElementAverageValue
variable = linesearch
outputs = 'console csv'
[../]
[./av_ld]
type = ElementAverageValue
variable = ld
outputs = 'console csv'
[../]
[./av_constr_added]
type = ElementAverageValue
variable = constr_added
outputs = 'console csv'
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 4E7
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 35
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningConstant
value = 5
convert_to_radians = true
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulombMulti
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
yield_function_tolerance = 1.0
shift = 1.0
internal_constraint_tolerance = 1.0E-7
[../]
[./mc_smooth]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
mc_tip_smoother = 4E6
yield_function_tolerance = 1.0
internal_constraint_tolerance = 1.0E-7
[../]
[./ts]
type = TensorMechanicsHardeningConstant
value = 1E6
[../]
[./tensile]
type = TensorMechanicsPlasticTensileMulti
tensile_strength = ts
yield_function_tolerance = 1.0
shift = 1.0
internal_constraint_tolerance = 1.0E-7
use_custom_returnMap = false
use_custom_cto = false
[../]
[./tensile_smooth]
type = TensorMechanicsPlasticTensile
tensile_strength = ts
tensile_tip_smoother = 1E5
yield_function_tolerance = 1.0
internal_constraint_tolerance = 1.0E-7
[../]
[./wpt_str]
type = TensorMechanicsHardeningConstant
value = 1.0E3
[../]
[./wpt]
type = TensorMechanicsPlasticWeakPlaneTensile
tensile_strength = wpt_str
yield_function_tolerance = 1.0
internal_constraint_tolerance = 1.0E-7
[../]
[./wps_c]
type = TensorMechanicsHardeningConstant
value = 1.0E5
[../]
[./wps_tan_phi]
type = TensorMechanicsHardeningConstant
value = 0.466
[../]
[./wps_tan_psi]
type = TensorMechanicsHardeningConstant
value = 0.087
[../]
[./wps]
type = TensorMechanicsPlasticWeakPlaneShear
cohesion = wps_c
tan_friction_angle = wps_tan_phi
tan_dilation_angle = wps_tan_psi
smoother = 1.0E4
yield_function_tolerance = 1.0
internal_constraint_tolerance = 1.0E-7
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '1.2E9 1.2E9'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-7
plastic_models = 'tensile_smooth mc_smooth wpt wps'
max_NR_iterations = 30
specialIC = 'none'
deactivation_scheme = 'optimized'
min_stepsize = 1E-6
max_stepsize_for_dumb = 1E-2
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1 1 1'
debug_jac_at_intnl = '1 1 1 1'
debug_stress_change = 1E1
debug_pm_change = '1E-6 1E-6 1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6 1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = paper3
exodus = false
csv = true
[]
(modules/tensor_mechanics/test/tests/multi/three_surface04.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 1.5
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 0.8E-6m in y direction and 1.5E-6 in z direction.
# trial stress_yy = 0.8 and stress_zz = 1.5
#
# Then SimpleTester0 and SimpleTester2 should activate and the algorithm will return to
# the corner stress_yy=0.5, stress_zz=1
# internal0 should be 0.2, and internal2 should be 0.3
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0.8E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1.5E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 1.5
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface04
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/finite_strain_tensor_mechanics_tests/elastic_rotation.i)
#
# Rotation Test
#
# This test is designed to compute a uniaxial stress and then follow that
# stress as the mesh is rotated 90 degrees.
#
# The mesh is composed of one block with a single element. The nodal
# displacements in the x and y directions are prescribed. Poisson's
# ratio is zero.
#
[Mesh]
file = rotation_test.e
[]
[GlobalParams]
displacements = 'disp_x disp_y disp_z'
[]
[Functions]
# Functions
[./x_200]
type = ParsedFunction
vars = 'delta t0'
vals = '-1e-6 1.0'
value = 'if(t<=1.0, delta*t, (1.0+delta)*cos(pi/2*(t-t0)) - 1.0)'
[../]
[./y_200]
type = ParsedFunction
vars = 'delta t0'
vals = '-1e-6 1.0'
value = 'if(t<=1.0, 0.0, (1.0+delta)*sin(pi/2*(t-t0)))'
[../]
[./x_300]
type = ParsedFunction
vars = 'delta t0'
vals = '-1e-6 1.0'
value = 'if(t<=1.0, delta*t, (1.0+delta)*cos(pi/2.0*(t-t0)) - sin(pi/2.0*(t-t0)) - 1.0)'
[../]
[./y_300]
type = ParsedFunction
vars = 'delta t0'
vals = '-1e-6 1.0'
value = 'if(t<=1.0, 0.0, cos(pi/2.0*(t-t0)) + (1+delta)*sin(pi/2.0*(t-t0)) - 1.0)'
[../]
[./x_400]
type = ParsedFunction
vars = 'delta t0'
vals = '-1e-6 1.0'
value = 'if(t<=1.0, 0.0, -sin(pi/2.0*(t-t0)))'
[../]
[./y_400]
type = ParsedFunction
vars = 'delta t0'
vals = '-1e-6 1.0'
value = 'if(t<=1.0, 0.0, cos(pi/2.0*(t-t0)) - 1.0)'
[../]
[]
[Variables]
# Variables
[./disp_x]
order = FIRST
family = LAGRANGE
[../]
[./disp_y]
order = FIRST
family = LAGRANGE
[../]
[./disp_z]
order = FIRST
family = LAGRANGE
[../]
[]
[AuxVariables]
# AuxVariables
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
[../]
[]
[AuxKernels]
# AuxKernels
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[]
[BCs]
# BCs
[./no_x]
type = DirichletBC
variable = disp_x
boundary = 100
value = 0.0
[../]
[./no_y]
type = DirichletBC
variable = disp_y
boundary = 100
value = 0.0
[../]
[./x_200]
type = FunctionDirichletBC
variable = disp_x
boundary = 200
function = x_200
[../]
[./y_200]
type = FunctionDirichletBC
variable = disp_y
boundary = 200
function = y_200
[../]
[./x_300]
type = FunctionDirichletBC
variable = disp_x
boundary = 300
function = x_300
[../]
[./y_300]
type = FunctionDirichletBC
variable = disp_y
boundary = 300
function = y_300
[../]
[./x_400]
type = FunctionDirichletBC
variable = disp_x
boundary = 400
function = x_400
[../]
[./y_400]
type = FunctionDirichletBC
variable = disp_y
boundary = 400
function = y_400
[../]
[./no_z]
type = DirichletBC
variable = disp_z
boundary = '100 200 300 400'
value = 0.0
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 1
C_ijkl = '1.0e6 0.0 0.0 1.0e6 0.0 1.0e6 0.5e6 0.5e6 0.5e6'
fill_method = symmetric9
[../]
[./strain]
type = ComputeFiniteStrain
block = 1
displacements = 'disp_x disp_y disp_z'
[../]
[./stress]
type = ComputeFiniteStrainElasticStress
block = 1
[../]
[]
[Postprocessors]
[./stress_xx]
type = ElementAverageValue
variable = stress_xx
[../]
[./stress_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./stress_xy]
type = ElementAverageValue
variable = stress_xy
[../]
[]
[Preconditioning]
[./SMP]
type = SMP
full = true
[../]
[]
[Executioner]
# Executioner
type = Transient
solve_type = 'NEWTON'
petsc_options_iname = '-pc_type '
petsc_options_value = 'lu'
nl_rel_tol = 1e-30
nl_abs_tol = 1e-20
l_max_its = 20
start_time = 0.0
dt = 0.01
end_time = 2.0
[]
[Outputs]
exodus = true
[] # Outputs
(modules/contact/test/tests/verification/patch_tests/brick_1/brick1_mu_0_2_pen.i)
[GlobalParams]
volumetric_locking_correction = true
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
file = brick1_mesh.e
[]
[Problem]
type = ReferenceResidualProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./penetration]
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./saved_z]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./diag_saved_z]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./inc_slip_z]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./accum_slip_z]
[../]
[./tang_force_x]
[../]
[./tang_force_y]
[../]
[./tang_force_z]
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y saved_z'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_end
boundary = 3
paired_boundary = 4
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_end
boundary = 3
paired_boundary = 4
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 3
paired_boundary = 4
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 3
paired_boundary = 4
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 3
paired_boundary = 4
[../]
[./tang_force_x]
type = PenetrationAux
variable = tang_force_x
quantity = tangential_force_x
boundary = 3
paired_boundary = 4
[../]
[./tang_force_y]
type = PenetrationAux
variable = tang_force_y
quantity = tangential_force_y
boundary = 3
paired_boundary = 4
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./ref_resid_x]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_x
[../]
[./ref_resid_y]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_y
[../]
[./sigma_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./sigma_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./disp_x5]
type = NodalVariableValue
nodeid = 4
variable = disp_x
[../]
[./disp_x8]
type = NodalVariableValue
nodeid = 7
variable = disp_x
[../]
[./disp_x13]
type = NodalVariableValue
nodeid = 12
variable = disp_x
[../]
[./disp_x16]
type = NodalVariableValue
nodeid = 15
variable = disp_x
[../]
[./disp_y5]
type = NodalVariableValue
nodeid = 4
variable = disp_y
[../]
[./disp_y8]
type = NodalVariableValue
nodeid = 7
variable = disp_y
[../]
[./disp_y13]
type = NodalVariableValue
nodeid = 12
variable = disp_y
[../]
[./disp_y16]
type = NodalVariableValue
nodeid = 15
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./bot_y]
type = DirichletBC
variable = disp_y
boundary = 1
value = 0.0
[../]
[./side_x]
type = DirichletBC
variable = disp_x
boundary = 2
value = 0.0
[../]
[./back_z]
type = DirichletBC
variable = disp_z
boundary = 6
value = 0.0
[../]
[./top_press]
type = Pressure
variable = disp_y
boundary = 5
factor = 109.89
[../]
[]
[Materials]
[./bot_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./bot_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./bot_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./top_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./top_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./top_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-9
nl_rel_tol = 1e-8
l_max_its = 50
nl_max_its = 100
dt = 1.0
end_time = 1.0
num_steps = 10
dtmin = 1.0
l_tol = 1e-5
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '1 3 4 5'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '1 3 4 5'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
file_base = brick1_mu_0_2_pen_out
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
file_base = brick1_mu_0_2_pen_check
show = 'bot_react_x bot_react_y disp_x5 disp_x8 disp_x13 disp_x16 disp_y5 disp_y8 disp_y13 disp_y16 stress_yy stress_zz top_react_x top_react_y x_disp y_disp cont_press'
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./leftright]
secondary = 3
primary = 4
model = coulomb
formulation = penalty
normalize_penalty = true
friction_coefficient = 0.2
penalty = 1e+9
[../]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/small_deform6.i)
# apply repeated stretches in z direction, and smaller stretches in the x and y directions
# so that sigma_II = sigma_III,
# which means that lode angle = -30deg.
# The allows yield surface in meridional plane to be mapped out
# Using cap smoothing
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0.9E-6*x*sin(t)'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0.9E-6*y*sin(t)'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1E-6*z*t'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./mc_int]
order = CONSTANT
family = MONOMIAL
[../]
[./yield_fcn]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./mc_int_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_internal_parameter
variable = mc_int
[../]
[./yield_fcn_auxk]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = yield_fcn
[../]
[./iter_auxk]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./internal]
type = PointValue
point = '0 0 0'
variable = mc_int
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = yield_fcn
[../]
[./iter]
type = PointValue
point = '0 0 0'
variable = iter
[../]
[]
[UserObjects]
[./mc_coh]
type = TensorMechanicsHardeningConstant
value = 10
[../]
[./mc_phi]
type = TensorMechanicsHardeningConstant
value = 50
convert_to_radians = true
[../]
[./mc_psi]
type = TensorMechanicsHardeningExponential
value_0 = 0
value_residual = 0.8726646 # 50deg
rate = 3000.0
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulomb
cohesion = mc_coh
friction_angle = mc_phi
dilation_angle = mc_psi
tip_scheme = cap
mc_tip_smoother = 0
cap_start = 3
cap_rate = 0.8
mc_edge_smoother = 20
yield_function_tolerance = 1E-8
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = mc
debug_fspb = crash
[../]
[]
[Executioner]
end_time = 30
dt = 1
type = Transient
[]
[Outputs]
file_base = small_deform6
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/contact/test/tests/verification/patch_tests/brick_1/brick1_aug.i)
[GlobalParams]
volumetric_locking_correction = true
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
file = brick1_mesh.e
[]
[Problem]
type = AugmentedLagrangianContactProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
maximum_lagrangian_update_iterations = 100
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./penetration]
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./saved_z]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./diag_saved_z]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./inc_slip_z]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./accum_slip_z]
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y saved_z'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 4
paired_boundary = 3
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./ref_resid_x]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_x
[../]
[./ref_resid_y]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_y
[../]
[./sigma_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./sigma_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./disp_x5]
type = NodalVariableValue
nodeid = 4
variable = disp_x
[../]
[./disp_x8]
type = NodalVariableValue
nodeid = 7
variable = disp_x
[../]
[./disp_x13]
type = NodalVariableValue
nodeid = 12
variable = disp_x
[../]
[./disp_x16]
type = NodalVariableValue
nodeid = 15
variable = disp_x
[../]
[./disp_y5]
type = NodalVariableValue
nodeid = 4
variable = disp_y
[../]
[./disp_y8]
type = NodalVariableValue
nodeid = 7
variable = disp_y
[../]
[./disp_y13]
type = NodalVariableValue
nodeid = 12
variable = disp_y
[../]
[./disp_y16]
type = NodalVariableValue
nodeid = 15
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./bot_y]
type = DirichletBC
variable = disp_y
boundary = 1
value = 0.0
[../]
[./side_x]
type = DirichletBC
variable = disp_x
boundary = 2
value = 0.0
[../]
[./back_z]
type = DirichletBC
variable = disp_z
boundary = 6
value = 0.0
[../]
[./top_press]
type = Pressure
variable = disp_y
boundary = 5
factor = 109.89
[../]
[]
[Materials]
[./bot_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./bot_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./bot_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./top_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./top_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./top_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-9
nl_rel_tol = 1e-8
l_max_its = 50
nl_max_its = 100
dt = 1.0
end_time = 1.0
num_steps = 10
dtmin = 1.0
l_tol = 1e-5
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '1 3 4 5'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '1 3 4 5'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
show = 'bot_react_x bot_react_y disp_x5 disp_x8 disp_x13 disp_x16 disp_y5 disp_y8 disp_y13 disp_y16 stress_yy stress_zz top_react_x top_react_y x_disp y_disp cont_press'
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./leftright]
secondary = 3
primary = 4
tangential_tolerance = 1e-3
formulation = augmented_lagrange
normalize_penalty = true
penalty = 1e8
model = frictionless
al_penetration_tolerance = 1e-8
[../]
[]
(modules/tensor_mechanics/test/tests/j2_plasticity/tensor_mechanics_j2plasticity.i)
[Mesh]
displacements = 'x_disp y_disp z_disp'
[generated_mesh]
type = GeneratedMeshGenerator
elem_type = HEX8
dim = 3
nx = 1
ny = 1
nz = 1
xmin = 0.0
xmax = 1.0
ymin = 0.0
ymax = 1.0
zmin = 0.0
zmax = 1.0
[]
[cnode]
type = ExtraNodesetGenerator
coord = '0.0 0.0 0.0'
new_boundary = 6
input = generated_mesh
[]
[snode]
type = ExtraNodesetGenerator
coord = '1.0 0.0 0.0'
new_boundary = 7
input = cnode
[]
[]
[Variables]
[./x_disp]
order = FIRST
family = LAGRANGE
[../]
[./y_disp]
order = FIRST
family = LAGRANGE
[../]
[./z_disp]
order = FIRST
family = LAGRANGE
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'x_disp y_disp z_disp'
use_displaced_mesh = true
[../]
[]
[Materials]
[./fplastic]
type = FiniteStrainPlasticMaterial
block=0
yield_stress='0. 445. 0.05 610. 0.1 680. 0.38 810. 0.95 920. 2. 950.'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
C_ijkl = '2.827e5 1.21e5 1.21e5 2.827e5 1.21e5 2.827e5 0.808e5 0.808e5 0.808e5'
fill_method = symmetric9
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'x_disp y_disp z_disp'
[../]
[]
[Functions]
[./topfunc]
type = ParsedFunction
value = 't'
[../]
[]
[BCs]
[./bottom3]
type = DirichletBC
variable = z_disp
boundary = 0
value = 0.0
[../]
[./top]
type = FunctionDirichletBC
variable = z_disp
boundary = 5
function = topfunc
[../]
[./corner1]
type = DirichletBC
variable = x_disp
boundary = 6
value = 0.0
[../]
[./corner2]
type = DirichletBC
variable = y_disp
boundary = 6
value = 0.0
[../]
[./corner3]
type = DirichletBC
variable = z_disp
boundary = 6
value = 0.0
[../]
[./side1]
type = DirichletBC
variable = y_disp
boundary = 7
value = 0.0
[../]
[./side2]
type = DirichletBC
variable = z_disp
boundary = 7
value = 0.0
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./peeq]
order = CONSTANT
family = MONOMIAL
[../]
[./pe11]
order = CONSTANT
family = MONOMIAL
[../]
[./pe22]
order = CONSTANT
family = MONOMIAL
[../]
[./pe33]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./pe11]
type = RankTwoAux
rank_two_tensor = plastic_strain
variable = pe11
index_i = 0
index_j = 0
[../]
[./pe22]
type = RankTwoAux
rank_two_tensor = plastic_strain
variable = pe22
index_i = 1
index_j = 1
[../]
[./pe33]
type = RankTwoAux
rank_two_tensor = plastic_strain
variable = pe33
index_i = 2
index_j = 2
[../]
[./eqv_plastic_strain]
type = MaterialRealAux
property = eqv_plastic_strain
variable = peeq
[../]
[]
[Preconditioning]
[./SMP]
type = SMP
full=true
[../]
[]
[Executioner]
type = Transient
dt=0.1
dtmax=1
dtmin=0.1
end_time=1.0
nl_abs_tol = 1e-10
[]
[Outputs]
file_base = out
exodus = true
[]
(modules/contact/test/tests/verification/patch_tests/brick_2/brick2_template1.i)
[GlobalParams]
volumetric_locking_correction = true
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
file = brick2_mesh.e
[]
[Problem]
type = ReferenceResidualProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./penetration]
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./saved_z]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./diag_saved_z]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./inc_slip_z]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./accum_slip_z]
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y saved_z'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 4
paired_boundary = 3
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./ref_resid_x]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_x
[../]
[./ref_resid_y]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_y
[../]
[./sigma_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./sigma_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./disp_x7]
type = NodalVariableValue
nodeid = 6
variable = disp_x
[../]
[./disp_x26]
type = NodalVariableValue
nodeid = 25
variable = disp_x
[../]
[./disp_y7]
type = NodalVariableValue
nodeid = 6
variable = disp_y
[../]
[./disp_y26]
type = NodalVariableValue
nodeid = 25
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./bot_y]
type = DirichletBC
variable = disp_y
boundary = 1
value = 0.0
[../]
[./side_x]
type = DirichletBC
variable = disp_x
boundary = 2
value = 0.0
[../]
[./back_z]
type = DirichletBC
variable = disp_z
boundary = 6
value = 0.0
[../]
[./top_press]
type = Pressure
variable = disp_y
boundary = 5
factor = 109.89
[../]
[]
[Materials]
[./bot_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./bot_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./bot_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./top_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./top_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./top_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-9
nl_rel_tol = 1e-8
l_max_its = 50
nl_max_its = 100
dt = 1.0
end_time = 1.0
num_steps = 10
dtmin = 1.0
l_tol = 1e-5
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '1 3 4 5'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '1 3 4 5'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
show = 'bot_react_x bot_react_y disp_x7 disp_y7 disp_x26 disp_y26 stress_yy stress_zz top_react_x top_react_y x_disp y_disp cont_press'
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./leftright]
secondary = 3
primary = 4
normalize_penalty = true
tangential_tolerance = 1e-3
penalty = 1e+9
[../]
[]
(modules/contact/test/tests/verification/patch_tests/brick_2/brick2_template2.i)
[GlobalParams]
volumetric_locking_correction = true
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
file = brick2_mesh.e
[]
[Problem]
type = AugmentedLagrangianContactProblem
maximum_lagrangian_update_iterations = 200
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./penetration]
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./saved_z]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./diag_saved_z]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./inc_slip_z]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./accum_slip_z]
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y saved_z'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 4
paired_boundary = 3
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./ref_resid_x]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_x
[../]
[./ref_resid_y]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_y
[../]
[./sigma_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./sigma_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./disp_x7]
type = NodalVariableValue
nodeid = 6
variable = disp_x
[../]
[./disp_x26]
type = NodalVariableValue
nodeid = 25
variable = disp_x
[../]
[./disp_y7]
type = NodalVariableValue
nodeid = 6
variable = disp_y
[../]
[./disp_y26]
type = NodalVariableValue
nodeid = 25
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./bot_y]
type = DirichletBC
variable = disp_y
boundary = 1
value = 0.0
[../]
[./side_x]
type = DirichletBC
variable = disp_x
boundary = 2
value = 0.0
[../]
[./back_z]
type = DirichletBC
variable = disp_z
boundary = 6
value = 0.0
[../]
[./top_press]
type = Pressure
variable = disp_y
boundary = 5
factor = 109.89
[../]
[]
[Materials]
[./bot_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./bot_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./bot_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./top_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./top_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./top_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-9
nl_rel_tol = 1e-8
l_max_its = 50
nl_max_its = 100
dt = 1.0
end_time = 1.0
num_steps = 10
dtmin = 1.0
l_tol = 1e-5
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '1 3 4 5'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '1 3 4 5'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
show = 'bot_react_x bot_react_y disp_x7 disp_y7 disp_x26 disp_y26 stress_yy stress_zz top_react_x top_react_y x_disp y_disp cont_press'
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./leftright]
secondary = 3
primary = 4
normalize_penalty = true
tangential_tolerance = 1e-3
penalty = 1e+7
al_penetration_tolerance = 1e-8
[../]
[]
(modules/tensor_mechanics/test/tests/multi/four_surface24.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 2 and strength = 3.1
# SimpleTester3 with a = 2 and b = 1 and strength = 3.1
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 2.1E-6m in y direction and 3E-6 in z direction.
# trial stress_yy = 2.1 and stress_zz = 3.0
#
# This is similar to four_surface14.i, and a description is found there.
# The result should be stress_zz=1=stress_yy, with internal0=2
# and internal1=1.1
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '2.1E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '3.0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./f3]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[./int3]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./f3]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 3
variable = f3
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[./int3]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 3
variable = int3
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./f3]
type = PointValue
point = '0 0 0'
variable = f3
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[./int3]
type = PointValue
point = '0 0 0'
variable = int3
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 2
strength = 3.1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[./simple3]
type = TensorMechanicsPlasticSimpleTester
a = 2
b = 1
strength = 3.1
yield_function_tolerance = 1.0E-6
internal_constraint_tolerance = 1.0E-6
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2 simple3'
deactivation_scheme = 'optimized_to_safe'
max_NR_iterations = 4
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1 1'
debug_jac_at_intnl = '1 1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = four_surface24
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/multi/three_surface09.i)
# Plasticit models:
# SimpleTester0 with a = 0 and b = 1 and strength = 1
# SimpleTester1 with a = 1 and b = 0 and strength = 1
# SimpleTester2 with a = 1 and b = 1 and strength = 1.5
#
# Lame lambda = 0 (Poisson=0). Lame mu = 0.5E6
#
# A single element is stretched by 2.0E-6m in y direction and 0.0E-6 in z direction.
# trial stress_yy = 2.0 and stress_zz = 0.0
#
# Then SimpleTester1 and SimpleTester2 should activate and the algorithm will return to
# the corner stress_yy=1.0, stress_zz=0.5
# However, this will mean that internal2<0, so SimpleTester2 will be deactivated
# and the algorithm will return to stress_yy=1
# internal1 should be 1.0, and internal2 should be 0
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '2.0E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0.0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f0]
order = CONSTANT
family = MONOMIAL
[../]
[./f1]
order = CONSTANT
family = MONOMIAL
[../]
[./f2]
order = CONSTANT
family = MONOMIAL
[../]
[./int0]
order = CONSTANT
family = MONOMIAL
[../]
[./int1]
order = CONSTANT
family = MONOMIAL
[../]
[./int2]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f0]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 0
variable = f0
[../]
[./f1]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 1
variable = f1
[../]
[./f2]
type = MaterialStdVectorAux
property = plastic_yield_function
index = 2
variable = f2
[../]
[./int0]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 0
variable = int0
[../]
[./int1]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 1
variable = int1
[../]
[./int2]
type = MaterialStdVectorAux
property = plastic_internal_parameter
factor = 1E6
index = 2
variable = int2
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f0]
type = PointValue
point = '0 0 0'
variable = f0
[../]
[./f1]
type = PointValue
point = '0 0 0'
variable = f1
[../]
[./f2]
type = PointValue
point = '0 0 0'
variable = f2
[../]
[./int0]
type = PointValue
point = '0 0 0'
variable = int0
[../]
[./int1]
type = PointValue
point = '0 0 0'
variable = int1
[../]
[./int2]
type = PointValue
point = '0 0 0'
variable = int2
[../]
[]
[UserObjects]
[./simple0]
type = TensorMechanicsPlasticSimpleTester
a = 0
b = 1
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple1]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 0
strength = 1
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[./simple2]
type = TensorMechanicsPlasticSimpleTester
a = 1
b = 1
strength = 1.5
yield_function_tolerance = 1.0E-9
internal_constraint_tolerance = 1.0E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 0.5E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = 'simple0 simple1 simple2'
max_NR_iterations = 2
min_stepsize = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1'
debug_jac_at_intnl = '1 1'
debug_stress_change = 1E-5
debug_pm_change = '1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = three_surface09
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/elastic_patch/elastic_patch.i)
# Patch Test
# This test is designed to compute constant xx, yy, zz, xy, yz, and zx
# stress on a set of irregular hexes. The mesh is composed of one
# block with seven elements. The elements form a unit cube with one
# internal element. There is a nodeset for each exterior node.
# The cube is displaced by 1e-6 units in x, 2e-6 in y, and 3e-6 in z.
# The faces are sheared as well (1e-6, 2e-6, and 3e-6 for xy, yz, and
# zx). This gives a uniform strain/stress state for all six unique
# tensor components.
# With Young's modulus at 1e6 and Poisson's ratio at 0, the shear
# modulus is 5e5 (G=E/2/(1+nu)). Therefore,
#
# stress xx = 1e6 * 1e-6 = 1
# stress yy = 1e6 * 2e-6 = 2
# stress zz = 1e6 * 3e-6 = 3
# stress xy = 2 * 5e5 * 1e-6 / 2 = 0.5
# (2 * G * gamma_xy / 2 = 2 * G * epsilon_xy)
# stress yz = 2 * 5e5 * 2e-6 / 2 = 1
# stress zx = 2 * 5e5 * 3e-6 / 2 = 1.5
[GlobalParams]
displacements = 'disp_x disp_y disp_z'
block = '1 2 3 4 5 6 7'
[]
[Mesh]#Comment
file = elastic_patch.e
[] # Mesh
[Functions]
[./rampConstant1]
type = PiecewiseLinear
x = '0. 1. 2.'
y = '0. 1. 1.'
scale_factor = 1e-6
[../]
[./rampConstant2]
type = PiecewiseLinear
x = '0. 1. 2.'
y = '0. 1. 1.'
scale_factor = 2e-6
[../]
[./rampConstant3]
type = PiecewiseLinear
x = '0. 1. 2.'
y = '0. 1. 1.'
scale_factor = 3e-6
[../]
[./rampConstant4]
type = PiecewiseLinear
x = '0. 1. 2.'
y = '0. 1. 1.'
scale_factor = 4e-6
[../]
[./rampConstant6]
type = PiecewiseLinear
x = '0. 1. 2.'
y = '0. 1. 1.'
scale_factor = 6e-6
[../]
[] # Functions
[Variables]
[./disp_x]
order = FIRST
family = LAGRANGE
[../]
[./disp_y]
order = FIRST
family = LAGRANGE
[../]
[./disp_z]
order = FIRST
family = LAGRANGE
[../]
[] # Variables
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zx]
order = CONSTANT
family = MONOMIAL
[../]
[./elastic_energy]
order = CONSTANT
family = MONOMIAL
[../]
[./vonmises]
order = CONSTANT
family = MONOMIAL
[../]
[./hydrostatic]
order = CONSTANT
family = MONOMIAL
[../]
[./firstinv]
order = CONSTANT
family = MONOMIAL
[../]
[./secondinv]
order = CONSTANT
family = MONOMIAL
[../]
[./thirdinv]
order = CONSTANT
family = MONOMIAL
[../]
[./maxprincipal]
order = CONSTANT
family = MONOMIAL
[../]
[./midprincipal]
order = CONSTANT
family = MONOMIAL
[../]
[./minprincipal]
order = CONSTANT
family = MONOMIAL
[../]
[./direction]
order = CONSTANT
family = MONOMIAL
[../]
[./max_shear]
order = CONSTANT
family = MONOMIAL
[../]
[./sint]
order = CONSTANT
family = MONOMIAL
[../]
[] # AuxVariables
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zx
index_i = 2
index_j = 0
[../]
[./elastic_energy]
type = ElasticEnergyAux
variable = elastic_energy
[../]
[./vonmises]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = vonmises
scalar_type = vonmisesStress
[../]
[./hydrostatic]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = hydrostatic
scalar_type = hydrostatic
[../]
[./fi]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = firstinv
scalar_type = firstinvariant
[../]
[./si]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = secondinv
scalar_type = secondinvariant
[../]
[./ti]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = thirdinv
scalar_type = thirdinvariant
[../]
[./maxprincipal]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = maxprincipal
scalar_type = MaxPRiNCIpAl
[../]
[./midprincipal]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = midprincipal
scalar_type = MidPRiNCIpAl
[../]
[./minprincipal]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = minprincipal
scalar_type = MiNPRiNCIpAl
[../]
[./direction]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = direction
scalar_type = direction
direction = '1 1 1'
[../]
[./max_shear]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = max_shear
scalar_type = MaxShear
[../]
[./sint]
type = RankTwoScalarAux
rank_two_tensor = stress
variable = sint
scalar_type = StressIntensity
[../]
[] # AuxKernels
[BCs]
[./node1_x]
type = DirichletBC
variable = disp_x
boundary = 1
value = 0.0
[../]
[./node1_y]
type = FunctionDirichletBC
variable = disp_y
boundary = 1
function = rampConstant2
[../]
[./node1_z]
type = FunctionDirichletBC
variable = disp_z
boundary = 1
function = rampConstant3
[../]
[./node2_x]
type = FunctionDirichletBC
variable = disp_x
boundary = 2
function = rampConstant1
[../]
[./node2_y]
type = FunctionDirichletBC
variable = disp_y
boundary = 2
function = rampConstant2
[../]
[./node2_z]
type = FunctionDirichletBC
variable = disp_z
boundary = 2
function = rampConstant6
[../]
[./node3_x]
type = FunctionDirichletBC
variable = disp_x
boundary = 3
function = rampConstant1
[../]
[./node3_y]
type = DirichletBC
variable = disp_y
boundary = 3
value = 0.0
[../]
[./node3_z]
type = FunctionDirichletBC
variable = disp_z
boundary = 3
function = rampConstant3
[../]
[./node4_x]
type = DirichletBC
variable = disp_x
boundary = 4
value = 0.0
[../]
[./node4_y]
type = DirichletBC
variable = disp_y
boundary = 4
value = 0.0
[../]
[./node4_z]
type = DirichletBC
variable = disp_z
boundary = 4
value = 0.0
[../]
[./node5_x]
type = FunctionDirichletBC
variable = disp_x
boundary = 5
function = rampConstant1
[../]
[./node5_y]
type = FunctionDirichletBC
variable = disp_y
boundary = 5
function = rampConstant4
[../]
[./node5_z]
type = FunctionDirichletBC
variable = disp_z
boundary = 5
function = rampConstant3
[../]
[./node6_x]
type = FunctionDirichletBC
variable = disp_x
boundary = 6
function = rampConstant2
[../]
[./node6_y]
type = FunctionDirichletBC
variable = disp_y
boundary = 6
function = rampConstant4
[../]
[./node6_z]
type = FunctionDirichletBC
variable = disp_z
boundary = 6
function = rampConstant6
[../]
[./node7_x]
type = FunctionDirichletBC
variable = disp_x
boundary = 7
function = rampConstant2
[../]
[./node7_y]
type = FunctionDirichletBC
variable = disp_y
boundary = 7
function = rampConstant2
[../]
[./node7_z]
type = FunctionDirichletBC
variable = disp_z
boundary = 7
function = rampConstant3
[../]
[./node8_x]
type = FunctionDirichletBC
variable = disp_x
boundary = 8
function = rampConstant1
[../]
[./node8_y]
type = FunctionDirichletBC
variable = disp_y
boundary = 8
function = rampConstant2
[../]
[./node8_z]
type = DirichletBC
variable = disp_z
boundary = 8
value = 0.0
[../]
[] # BCs
[Materials]
[./elasticity_tensor]
type = ComputeIsotropicElasticityTensor
youngs_modulus = 1e6
poissons_ratio = 0.0
[../]
[./strain]
type = ComputeFiniteStrain
[../]
[./stress]
type = ComputeFiniteStrainElasticStress
[../]
[] # Materials
[Executioner]
type = Transient
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
nl_abs_tol = 1e-10
l_max_its = 20
start_time = 0.0
dt = 1.0
num_steps = 2
end_time = 2.0
[] # Executioner
[Outputs]
exodus = true
[] # Outputs
(modules/contact/test/tests/verification/patch_tests/brick_2/brick2_mu_0_2_pen.i)
[GlobalParams]
volumetric_locking_correction = true
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
file = brick2_mesh.e
[]
[Problem]
type = ReferenceResidualProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./penetration]
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./saved_z]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./diag_saved_z]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./inc_slip_z]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./accum_slip_z]
[../]
[./tang_force_x]
[../]
[./tang_force_y]
[../]
[./tang_force_z]
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y saved_z'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_end
boundary = 3
paired_boundary = 4
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_end
boundary = 3
paired_boundary = 4
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 3
paired_boundary = 4
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 3
paired_boundary = 4
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 3
paired_boundary = 4
[../]
[./tang_force_x]
type = PenetrationAux
variable = tang_force_x
quantity = tangential_force_x
boundary = 3
paired_boundary = 4
[../]
[./tang_force_y]
type = PenetrationAux
variable = tang_force_y
quantity = tangential_force_y
boundary = 3
paired_boundary = 4
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./ref_resid_x]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_x
[../]
[./ref_resid_y]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_y
[../]
[./sigma_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./sigma_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./disp_x7]
type = NodalVariableValue
nodeid = 6
variable = disp_x
[../]
[./disp_x26]
type = NodalVariableValue
nodeid = 25
variable = disp_x
[../]
[./disp_y7]
type = NodalVariableValue
nodeid = 6
variable = disp_y
[../]
[./disp_y26]
type = NodalVariableValue
nodeid = 25
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./bot_y]
type = DirichletBC
variable = disp_y
boundary = 1
value = 0.0
[../]
[./side_x]
type = DirichletBC
variable = disp_x
boundary = 2
value = 0.0
[../]
[./back_z]
type = DirichletBC
variable = disp_z
boundary = 6
value = 0.0
[../]
[./top_press]
type = Pressure
variable = disp_y
boundary = 5
factor = 109.89
[../]
[]
[Materials]
[./bot_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./bot_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./bot_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./top_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./top_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./top_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-9
nl_rel_tol = 1e-8
l_max_its = 50
nl_max_its = 100
dt = 1.0
end_time = 1.0
num_steps = 10
dtmin = 1.0
l_tol = 1e-5
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '1 3 4 5'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '1 3 4 5'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
file_base = brick2_mu_0_2_pen_out
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
file_base = brick2_mu_0_2_pen_check
show = 'bot_react_x bot_react_y disp_x7 disp_y7 disp_x26 disp_y26 stress_yy stress_zz top_react_x top_react_y x_disp y_disp cont_press'
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./leftright]
secondary = 3
primary = 4
model = coulomb
formulation = penalty
normalize_penalty = true
friction_coefficient = 0.2
penalty = 1e+7
[../]
[]
(modules/tensor_mechanics/test/tests/mohr_coulomb/planar1.i)
# apply uniform stretch in x, y and z directions.
# With cohesion = 10, friction_angle = 60deg, the
# algorithm should return to
# sigma_m = 10*Cos(60)/Sin(60) = 5.773503
# using planar surfaces (not smoothed)
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '1E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '1.1E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '1.2E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = f
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = f
[../]
[./iter]
type = PointValue
point = '0 0 0'
variable = iter
[../]
[]
[UserObjects]
[./coh]
type = TensorMechanicsHardeningConstant
value = 10
[../]
[./phi]
type = TensorMechanicsHardeningConstant
value = 1.04719756
[../]
[./psi]
type = TensorMechanicsHardeningConstant
value = 0.1
[../]
[./mc]
type = TensorMechanicsPlasticMohrCoulombMulti
cohesion = coh
friction_angle = phi
dilation_angle = psi
yield_function_tolerance = 1E-3
shift = 1E-12
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E7'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-10
deactivation_scheme = safe
plastic_models = mc
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = 1
debug_jac_at_intnl = 1
debug_stress_change = 1E-5
debug_pm_change = 1E-6
debug_intnl_change = 1E-6
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = planar1
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/use_substep_dt.i)
[Mesh]
type = GeneratedMesh
dim = 3
nx = 4
ny = 4
nz = 4
elem_type = HEX8
displacements = 'ux uy uz'
[]
[Variables]
[./ux]
[../]
[./uy]
[../]
[./uz]
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./pk2]
order = CONSTANT
family = MONOMIAL
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./rotout]
order = CONSTANT
family = MONOMIAL
[../]
[./e_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./gss]
order = CONSTANT
family = MONOMIAL
[../]
[./slip_increment]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'ux uy uz'
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./pk2]
type = RankTwoAux
variable = pk2
rank_two_tensor = pk2
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./e_zz]
type = RankTwoAux
variable = e_zz
rank_two_tensor = lage
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./gss]
type = MaterialStdVectorAux
variable = gss
property = state_var_gss
index = 0
execute_on = timestep_end
[../]
[./slip_inc]
type = MaterialStdVectorAux
variable = slip_increment
property = slip_rate_gss
index = 0
execute_on = timestep_end
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = uy
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = ux
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = uz
boundary = back
value = 0
[../]
[./pushy]
type = FunctionDirichletBC
variable = uy
boundary = top
function = '-0.1*t'
[../]
[./pullz]
type = FunctionDirichletBC
variable = uz
boundary = front
function = '0.1*t'
[../]
[]
[UserObjects]
[./slip_rate_gss]
type = CrystalPlasticitySlipRateGSS
variable_size = 12
slip_sys_file_name = input_slip_sys.txt
num_slip_sys_flowrate_props = 2
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
uo_state_var_name = state_var_gss
[../]
[./slip_resistance_gss]
type = CrystalPlasticitySlipResistanceGSS
variable_size = 12
uo_state_var_name = state_var_gss
[../]
[./state_var_gss]
type = CrystalPlasticityStateVariable
variable_size = 12
groups = '0 4 8 12'
group_values = '60.8 60.8 60.8'
uo_state_var_evol_rate_comp_name = state_var_evol_rate_comp_gss
scale_factor = 1.0
[../]
[./state_var_evol_rate_comp_gss]
type = CrystalPlasticityStateVarRateComponentGSS
variable_size = 12
hprops = '1.0 541.5 109.8 2.5'
uo_slip_rate_name = slip_rate_gss
uo_state_var_name = state_var_gss
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainUObasedCP
block = 0
stol = 1e-2
tan_mod_type = exact
uo_slip_rates = 'slip_rate_gss'
uo_slip_resistances = 'slip_resistance_gss'
uo_state_vars = 'state_var_gss'
uo_state_var_evol_rate_comps = 'state_var_evol_rate_comp_gss'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'ux uy uz'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
block = 0
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./pk2]
type = ElementAverageValue
variable = pk2
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
[../]
[./e_zz]
type = ElementAverageValue
variable = e_zz
[../]
[./gss]
type = ElementAverageValue
variable = gss
[../]
[./slip_increment]
type = ElementAverageValue
variable = slip_increment
[../]
[./uy_avg_top]
type = SideAverageValue
variable = uy
boundary = top
[]
[./uz_avg_front]
type = SideAverageValue
variable = uz
boundary = front
[]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.05
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
nl_abs_tol = 1e-10
nl_rel_step_tol = 1e-10
dtmax = 10.0
nl_rel_tol = 1e-10
end_time = 1.0
num_steps = 5
dtmin = 0.001
nl_abs_step_tol = 1e-10
[]
[Outputs]
csv = true
[]
(modules/contact/test/tests/verification/hertz_cyl/half_symm_q4/hertz_cyl_half_1deg_template1.i)
[GlobalParams]
volumetric_locking_correction = true
displacements = 'disp_x disp_y'
[]
[Mesh]
file = hertz_cyl_half_1deg.e
[]
[Problem]
type = ReferenceResidualProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./tang_force_x]
[../]
[./tang_force_y]
[../]
[]
[Functions]
[./disp_ramp_vert]
type = PiecewiseLinear
x = '0. 1. 3.5'
y = '0. -0.0020 -0.0020'
[../]
[./disp_ramp_horz]
type = PiecewiseLinear
x = '0. 1. 3.5'
y = '0. 0.0 0.0014'
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_end
boundary = 3
paired_boundary = 2
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_end
boundary = 3
paired_boundary = 2
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 3
paired_boundary = 2
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 3
paired_boundary = 2
[../]
[./tang_force_x]
type = PenetrationAux
variable = tang_force_x
quantity = tangential_force_x
boundary = 3
paired_boundary = 2
[../]
[./tang_force_y]
type = PenetrationAux
variable = tang_force_y
quantity = tangential_force_y
boundary = 3
paired_boundary = 2
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 3
paired_boundary = 2
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 4
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 4
[../]
[./disp_x226]
type = NodalVariableValue
nodeid = 225
variable = disp_x
[../]
[./disp_y226]
type = NodalVariableValue
nodeid = 225
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./side_x]
type = DirichletBC
variable = disp_y
boundary = '1 2'
value = 0.0
[../]
[./bot_y]
type = DirichletBC
variable = disp_x
boundary = '1 2'
value = 0.0
[../]
[./top_y_disp]
type = FunctionDirichletBC
variable = disp_y
boundary = 4
function = disp_ramp_vert
[../]
[./top_x_disp]
type = FunctionDirichletBC
variable = disp_x
boundary = 4
function = disp_ramp_horz
[../]
[]
[Materials]
[./stuff1_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e10
poissons_ratio = 0.0
[../]
[./stuff1_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./stuff1_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./stuff2_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff2_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./stuff2_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[./stuff3_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '3'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff3_strain]
type = ComputeFiniteStrain
block = '3'
[../]
[./stuff3_stress]
type = ComputeFiniteStrainElasticStress
block = '3'
[../]
[./stuff4_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '4'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff4_strain]
type = ComputeFiniteStrain
block = '4'
[../]
[./stuff4_stress]
type = ComputeFiniteStrainElasticStress
block = '4'
[../]
[./stuff5_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '5'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff5_strain]
type = ComputeFiniteStrain
block = '5'
[../]
[./stuff5_stress]
type = ComputeFiniteStrainElasticStress
block = '5'
[../]
[./stuff6_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '6'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff6_strain]
type = ComputeFiniteStrain
block = '6'
[../]
[./stuff6_stress]
type = ComputeFiniteStrainElasticStress
block = '6'
[../]
[./stuff7_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '7'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff7_strain]
type = ComputeFiniteStrain
block = '7'
[../]
[./stuff7_stress]
type = ComputeFiniteStrainElasticStress
block = '7'
[../]
[]
[Executioner]
type = Transient
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-6
nl_rel_tol = 1e-5
l_max_its = 100
nl_max_its = 200
start_time = 0.0
end_time = 3.5
l_tol = 1e-3
dt = 0.1
dtmin = 0.1
[]
[Preconditioning]
[./SMP]
type = SMP
full = true
[../]
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '3 4'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '3 4'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
show = 'x_disp y_disp cont_press'
start_time = 0.9
execute_vector_postprocessors_on = timestep_end
[../]
[./chkfile2]
type = CSV
show = 'bot_react_x bot_react_y disp_x226 disp_y226 top_react_x top_react_y'
start_time = 0.9
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./interface]
primary = 2
secondary = 3
normalize_penalty = true
tangential_tolerance = 1e-3
penalty = 1e+10
[../]
[]
(modules/tensor_mechanics/test/tests/multi/special_joint1.i)
# Plasticity models:
# WeakPlaneTensile with strength = 1000Pa
# WeakPlaneShear with cohesion = 0.1MPa and friction angle = 25
#
# Lame lambda = 1GPa. Lame mu = 1.3GPa
#
# A line of elements is perturbed randomly, and return to the yield surface at each quadpoint is checked
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1000
ny = 125
nz = 1
xmin = 0
xmax = 1000
ymin = 0
ymax = 125
zmin = 0
zmax = 1
[]
[GlobalParams]
volumetric_locking_correction=true
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[ICs]
[./x]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_x
[../]
[./y]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_y
[../]
[./z]
type = RandomIC
min = -0.1
max = 0.1
variable = disp_z
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '0'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./linesearch]
order = CONSTANT
family = MONOMIAL
[../]
[./ld]
order = CONSTANT
family = MONOMIAL
[../]
[./constr_added]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./linesearch]
type = MaterialRealAux
property = plastic_linesearch_needed
variable = linesearch
[../]
[./ld]
type = MaterialRealAux
property = plastic_linear_dependence_encountered
variable = ld
[../]
[./constr_added]
type = MaterialRealAux
property = plastic_constraints_added
variable = constr_added
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[]
[Postprocessors]
[./max_iter]
type = ElementExtremeValue
variable = iter
outputs = console
[../]
[./av_linesearch]
type = ElementAverageValue
variable = linesearch
outputs = 'console csv'
[../]
[./av_ld]
type = ElementAverageValue
variable = ld
outputs = 'console csv'
[../]
[./av_constr_added]
type = ElementAverageValue
variable = constr_added
outputs = 'console csv'
[../]
[./av_iter]
type = ElementAverageValue
variable = iter
outputs = 'console csv'
[../]
[]
[UserObjects]
[./wpt_str]
type = TensorMechanicsHardeningConstant
value = 1000
[../]
[./wpt]
type = TensorMechanicsPlasticWeakPlaneTensile
tensile_strength = wpt_str
yield_function_tolerance = 1.0
internal_constraint_tolerance = 1.0E-7
[../]
[./wps_c]
type = TensorMechanicsHardeningConstant
value = 1.0E5
[../]
[./wps_tan_phi]
type = TensorMechanicsHardeningConstant
value = 0.466
[../]
[./wps_tan_psi]
type = TensorMechanicsHardeningConstant
value = 0.087
[../]
[./wps]
type = TensorMechanicsPlasticWeakPlaneShear
cohesion = wps_c
tan_friction_angle = wps_tan_phi
tan_dilation_angle = wps_tan_psi
smoother = 0
yield_function_tolerance = 1.0
internal_constraint_tolerance = 1.0E-7
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '1.0E9 1.3E9'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./multi]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-7
plastic_models = 'wpt wps'
max_NR_iterations = 5
specialIC = 'joint'
deactivation_scheme = 'safe'
min_stepsize = 1
max_stepsize_for_dumb = 1
debug_fspb = crash
debug_jac_at_stress = '10 0 0 0 10 0 0 0 10'
debug_jac_at_pm = '1 1 1 1'
debug_jac_at_intnl = '1 1 1 1'
debug_stress_change = 1E1
debug_pm_change = '1E-6 1E-6 1E-6 1E-6'
debug_intnl_change = '1E-6 1E-6 1E-6 1E-6'
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = special_joint1
exodus = false
csv = true
[]
(modules/contact/test/tests/verification/hertz_cyl/half_symm_q4/hertz_cyl_half_1deg_template3.i)
[GlobalParams]
order = FIRST
family = LAGRANGE
volumetric_locking_correction = true
displacements = 'disp_x disp_y'
[]
[Mesh]
file = hertz_cyl_half_1deg.e
[]
[Problem]
type = ReferenceResidualProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./tang_force_x]
[../]
[./tang_force_y]
[../]
[]
[Functions]
[./disp_ramp_vert]
type = PiecewiseLinear
x = '0. 1. 11.'
y = '0. -0.0020 -0.0020'
[../]
[./disp_ramp_horz]
type = PiecewiseLinear
x = '0. 1. 11.'
y = '0. 0.0 0.0014'
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
extra_vector_tags = 'ref'
save_in = 'saved_x saved_y'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_end
boundary = 3
paired_boundary = 2
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_end
boundary = 3
paired_boundary = 2
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 3
paired_boundary = 2
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 3
paired_boundary = 2
[../]
[./tang_force_x]
type = PenetrationAux
variable = tang_force_x
quantity = tangential_force_x
boundary = 3
paired_boundary = 2
[../]
[./tang_force_y]
type = PenetrationAux
variable = tang_force_y
quantity = tangential_force_y
boundary = 3
paired_boundary = 2
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 3
paired_boundary = 2
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 4
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 4
[../]
[./disp_x226]
type = NodalVariableValue
nodeid = 225
variable = disp_x
[../]
[./disp_y226]
type = NodalVariableValue
nodeid = 225
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./side_x]
type = DirichletBC
variable = disp_y
boundary = '1 2'
value = 0.0
[../]
[./bot_y]
type = DirichletBC
variable = disp_x
boundary = '1 2'
value = 0.0
[../]
[./top_y_disp]
type = FunctionDirichletBC
variable = disp_y
boundary = 4
function = disp_ramp_vert
[../]
[./top_x_disp]
type = FunctionDirichletBC
variable = disp_x
boundary = 4
function = disp_ramp_horz
[../]
[]
[Materials]
[./stuff1_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e10
poissons_ratio = 0.0
[../]
[./stuff1_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./stuff1_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./stuff2_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff2_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./stuff2_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[./stuff3_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '3'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff3_strain]
type = ComputeFiniteStrain
block = '3'
[../]
[./stuff3_stress]
type = ComputeFiniteStrainElasticStress
block = '3'
[../]
[./stuff4_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '4'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff4_strain]
type = ComputeFiniteStrain
block = '4'
[../]
[./stuff4_stress]
type = ComputeFiniteStrainElasticStress
block = '4'
[../]
[./stuff5_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '5'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff5_strain]
type = ComputeFiniteStrain
block = '5'
[../]
[./stuff5_stress]
type = ComputeFiniteStrainElasticStress
block = '5'
[../]
[./stuff6_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '6'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff6_strain]
type = ComputeFiniteStrain
block = '6'
[../]
[./stuff6_stress]
type = ComputeFiniteStrainElasticStress
block = '6'
[../]
[./stuff7_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '7'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./stuff7_strain]
type = ComputeFiniteStrain
block = '7'
[../]
[./stuff7_stress]
type = ComputeFiniteStrainElasticStress
block = '7'
[../]
[]
[Executioner]
type = Transient
#Preconditioned JFNK (default)
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-7
nl_rel_tol = 1e-6
l_max_its = 100
nl_max_its = 200
start_time = 0.0
end_time = 2.0
l_tol = 5e-4
dt = 0.1
dtmin = 0.1
[]
[Preconditioning]
[./SMP]
type = SMP
full = true
[../]
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '3 4'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '3 4'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
show = 'x_disp y_disp cont_press'
start_time = 0.9
execute_vector_postprocessors_on = timestep_end
[../]
[./chkfile2]
type = CSV
show = 'bot_react_x bot_react_y disp_x226 disp_y226 top_react_x top_react_y'
start_time = 0.9
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./interface]
primary = 2
secondary = 3
model = coulomb
friction_coefficient = 0.0
formulation = penalty
normalize_penalty = true
tangential_tolerance = 1e-3
penalty = 1e+9
[../]
[]
[Dampers]
[./contact_slip]
type = ContactSlipDamper
primary = '2'
secondary = '3'
[../]
[]
(modules/xfem/test/tests/moving_interface/moving_bimaterial_finite_strain_esm_using_cut_mesh.i)
# This test is for two layer materials with different youngs modulus with AD
# The global stress is determined by switching the stress based on level set values
# The material interface is marked by a level set function
# The two layer materials are glued together
[GlobalParams]
displacements = 'disp_x disp_y'
[]
[XFEM]
output_cut_plane = true
[]
[UserObjects]
[cut]
type = InterfaceMeshCut2DUserObject
mesh_file = line.e
interface_velocity_function = 1
heal_always = true
[]
[esm]
type = CutElementSubdomainModifier
geometric_cut_userobject = cut
apply_initial_conditions = false
[]
[]
[Mesh]
use_displaced_mesh = true
[generated_mesh]
type = GeneratedMeshGenerator
dim = 2
nx = 10
ny = 10
xmin = 0
xmax = 5
ymin = 0
ymax = 5
elem_type = QUAD4
[]
[bottom]
type = SubdomainBoundingBoxGenerator
input = generated_mesh
block_id = 0
bottom_left = '0 0 0'
top_right = '5 2.5 0'
[]
[top]
type = SubdomainBoundingBoxGenerator
input = bottom
block_id = 1
bottom_left = '0 2.5 0'
top_right = '5 5 0'
[]
[]
[Functions]
[ls_func]
type = ParsedFunction
value = 'y-2.73+t'
[]
[]
[Variables]
[disp_x]
[]
[disp_y]
[]
[]
[AuxVariables]
[ls]
[]
[strain_xx]
order = CONSTANT
family = MONOMIAL
[]
[strain_yy]
order = CONSTANT
family = MONOMIAL
[]
[strain_xy]
order = CONSTANT
family = MONOMIAL
[]
[stress_xx]
order = CONSTANT
family = MONOMIAL
[]
[stress_yy]
order = CONSTANT
family = MONOMIAL
[]
[stress_xy]
order = CONSTANT
family = MONOMIAL
[]
[]
[AuxKernels]
[ls_function]
type = FunctionAux
variable = ls
function = ls_func
[]
[strain_xx]
type = RankTwoAux
variable = strain_xx
rank_two_tensor = total_strain
index_i = 0
index_j = 0
[]
[strain_yy]
type = RankTwoAux
variable = strain_yy
rank_two_tensor = total_strain
index_i = 1
index_j = 1
[]
[strain_xy]
type = RankTwoAux
variable = strain_xy
rank_two_tensor = total_strain
index_i = 0
index_j = 1
[]
[stress_xx]
type = RankTwoAux
variable = stress_xx
rank_two_tensor = stress
index_i = 0
index_j = 0
[]
[stress_xy]
type = RankTwoAux
variable = stress_xy
rank_two_tensor = stress
index_i = 0
index_j = 1
[]
[stress_yy]
type = RankTwoAux
variable = stress_yy
rank_two_tensor = stress
index_i = 1
index_j = 1
[]
[]
[Kernels]
[solid_x]
type = StressDivergenceTensors
variable = disp_x
component = 0
use_displaced_mesh = true
[]
[solid_y]
type = StressDivergenceTensors
variable = disp_y
component = 1
use_displaced_mesh = true
[]
[]
[Constraints]
[dispx_constraint]
type = XFEMSingleVariableConstraint
use_displaced_mesh = false
variable = disp_x
alpha = 1e8
geometric_cut_userobject = 'cut'
[]
[dispy_constraint]
type = XFEMSingleVariableConstraint
use_displaced_mesh = false
variable = disp_y
alpha = 1e8
geometric_cut_userobject = 'cut'
[]
[]
[BCs]
[bottomx]
type = DirichletBC
boundary = bottom
variable = disp_x
value = 0.0
[]
[bottomy]
type = DirichletBC
boundary = bottom
variable = disp_y
value = 0.0
[]
[topx]
type = FunctionDirichletBC
boundary = top
variable = disp_x
function = 0.03*t
[]
[topy]
type = FunctionDirichletBC
boundary = top
variable = disp_y
function = '0.03*t'
[]
[]
[Materials]
[elasticity_tensor_A]
type = ComputeIsotropicElasticityTensor
block = 1
youngs_modulus = 1e9
poissons_ratio = 0.3
[]
[strain_A]
type = ComputeFiniteStrain
block = 1
[]
[stress_A]
type = ComputeFiniteStrainElasticStress
block = 1
[]
[elasticity_tensor_B]
type = ComputeIsotropicElasticityTensor
block = 0
youngs_modulus = 1e7
poissons_ratio = 0.3
[]
[strain_B]
type = ComputeFiniteStrain
block = 0
[]
[stress_B]
type = ComputeFiniteStrainElasticStress
block = 0
[]
[]
[Postprocessors]
[disp_x_norm]
type = ElementL2Norm
variable = disp_x
[]
[disp_y_norm]
type = ElementL2Norm
variable = disp_y
[]
[]
[Executioner]
type = Transient
solve_type = NEWTON
petsc_options_iname = '-pc_type'
petsc_options_value = 'lu'
automatic_scaling = true
# controls for nonlinear iterations
nl_max_its = 15
nl_rel_tol = 1e-13
nl_abs_tol = 1e-50
# time control
start_time = 0.0
dt = 0.1
num_steps = 4
max_xfem_update = 1
[]
[Outputs]
print_linear_residuals = false
exodus = true
[]
(modules/tensor_mechanics/test/tests/isotropicSD_plasticity/powerRuleHardening.i)
# UserObject IsotropicSD test, with power rule hardening with rate 1e2.
# Linear strain is applied in the x and y direction.
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -.5
xmax = .5
ymin = -.5
ymax = .5
zmin = -.5
zmax = .5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./xdisp]
type = FunctionDirichletBC
variable = disp_x
boundary = 'right'
function = '0.005*t'
[../]
[./ydisp]
type = FunctionDirichletBC
variable = disp_y
boundary = 'top'
function = '0.005*t'
[../]
[./yfix]
type = DirichletBC
variable = disp_y
#boundary = 'bottom top'
boundary = 'bottom'
value = 0
[../]
[./xfix]
type = DirichletBC
variable = disp_x
boundary = 'left'
value = 0
[../]
[./zfix]
type = DirichletBC
variable = disp_z
#boundary = 'front back'
boundary = 'back'
value = 0
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./plastic_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./plastic_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./plastic_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./plastic_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./plastic_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./plastic_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[./intnl]
order = CONSTANT
family = MONOMIAL
[../]
[./sdev]
order = CONSTANT
family = MONOMIAL
[../]
[./sdet]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./plastic_xx]
type = RankTwoAux
rank_two_tensor = plastic_strain
variable = plastic_xx
index_i = 0
index_j = 0
[../]
[./plastic_xy]
type = RankTwoAux
rank_two_tensor = plastic_strain
variable = plastic_xy
index_i = 0
index_j = 1
[../]
[./plastic_xz]
type = RankTwoAux
rank_two_tensor = plastic_strain
variable = plastic_xz
index_i = 0
index_j = 2
[../]
[./plastic_yy]
type = RankTwoAux
rank_two_tensor = plastic_strain
variable = plastic_yy
index_i = 1
index_j = 1
[../]
[./plastic_yz]
type = RankTwoAux
rank_two_tensor = plastic_strain
variable = plastic_yz
index_i = 1
index_j = 2
[../]
[./plastic_zz]
type = RankTwoAux
rank_two_tensor = plastic_strain
variable = plastic_zz
index_i = 2
index_j = 2
[../]
[./f]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = f
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[./intnl]
type = MaterialStdVectorAux
index = 0
property = plastic_internal_parameter
variable = intnl
[../]
[./sdev]
type = RankTwoScalarAux
variable = sdev
rank_two_tensor = stress
scalar_type = VonMisesStress
[../]
[]
[Postprocessors]
[./sdev]
type = PointValue
point = '0 0 0'
variable = sdev
[../]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./p_xx]
type = PointValue
point = '0 0 0'
variable = plastic_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./p_xy]
type = PointValue
point = '0 0 0'
variable = plastic_xy
[../]
[./p_xz]
type = PointValue
point = '0 0 0'
variable = plastic_xz
[../]
[./p_yz]
type = PointValue
point = '0 0 0'
variable = plastic_yz
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./p_yy]
type = PointValue
point = '0 0 0'
variable = plastic_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./p_zz]
type = PointValue
point = '0 0 0'
variable = plastic_zz
[../]
[./intnl]
type = PointValue
point = '0 0 0'
variable = intnl
[../]
[]
[UserObjects]
[./str]
type = TensorMechanicsHardeningPowerRule
value_0 = 300
epsilon0 = 1
exponent = 1e2
[../]
[./IsotropicSD]
type = TensorMechanicsPlasticIsotropicSD
b = -0.2
c = -0.779422863
associative = true
yield_strength = str
yield_function_tolerance = 1e-5
internal_constraint_tolerance = 1e-9
use_custom_returnMap = false
use_custom_cto = false
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '121e3 80e3'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1e-9
plastic_models = IsotropicSD
debug_fspb = crash
tangent_operator = elastic
[../]
[]
[Executioner]
num_steps = 3
dt = .5
type = Transient
nl_rel_tol = 1e-6
nl_max_its = 10
l_tol = 1e-4
l_max_its = 50
solve_type = PJFNK
petsc_options_iname = '-pc_type'
petsc_options_value = 'lu'
[]
[Outputs]
perf_graph = false
csv = true
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/monolithic_material_based/crysp_cutback.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'ux uy uz'
[]
[Variables]
[./ux]
block = 0
[../]
[./uy]
block = 0
[../]
[./uz]
block = 0
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./rotout]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./e_zz]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[./gss1]
order = CONSTANT
family = MONOMIAL
block = 0
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'ux uy uz'
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./e_zz]
type = RankTwoAux
variable = e_zz
rank_two_tensor = lage
index_j = 2
index_i = 2
execute_on = timestep_end
block = 0
[../]
[./gss1]
type = MaterialStdVectorAux
variable = gss1
property = gss
index = 0
execute_on = timestep_end
block = 0
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = uy
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = ux
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = uz
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = uz
boundary = front
function = tdisp
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainCrystalPlasticity
block = 0
gtol = 1e-2
slip_sys_file_name = input_slip_sys.txt
nss = 12
num_slip_sys_flowrate_props = 2 #Number of properties in a slip system
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
hprops = '1.0 541.5 60.8 109.8 2.5'
gprops = '1 4 60.8 5 8 60.8 9 12 60.8'
tan_mod_type = exact
gen_random_stress_flag = true
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
block = 0
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'ux uy uz'
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./e_zz]
type = ElementAverageValue
variable = e_zz
block = 'ANY_BLOCK_ID 0'
[../]
[./gss1]
type = ElementAverageValue
variable = gss1
block = 'ANY_BLOCK_ID 0'
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_factor_shift_type'
petsc_options_value = 'nonzero'
nl_rel_tol = 1e-10
nl_abs_tol = 1e-10
dt = 1.0
dtmax = 10.0
dtmin = 1e-5
num_steps = 3
snesmf_reuse_base = false
[]
[Outputs]
file_base = crysp_cutback_out
exodus = true
csv = true
gnuplot = true
[]
(modules/contact/test/tests/verification/patch_tests/brick_3/brick3_template1.i)
[GlobalParams]
order = SECOND
displacements = 'disp_x disp_y disp_z'
[]
[Mesh]
file = brick3_mesh.e
[]
[Problem]
type = ReferenceResidualProblem
extra_tag_vectors = 'ref'
reference_vector = 'ref'
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./penetration]
[../]
[./saved_x]
[../]
[./saved_y]
[../]
[./saved_z]
[../]
[./diag_saved_x]
[../]
[./diag_saved_y]
[../]
[./diag_saved_z]
[../]
[./inc_slip_x]
[../]
[./inc_slip_y]
[../]
[./inc_slip_z]
[../]
[./accum_slip_x]
[../]
[./accum_slip_y]
[../]
[./accum_slip_z]
[../]
[]
[Kernels]
[./TensorMechanics]
use_displaced_mesh = true
save_in = 'saved_x saved_y saved_z'
extra_vector_tags = 'ref'
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
execute_on = timestep_end
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
execute_on = timestep_end
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
execute_on = timestep_end
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
execute_on = timestep_end
[../]
[./inc_slip_x]
type = PenetrationAux
variable = inc_slip_x
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./inc_slip_y]
type = PenetrationAux
variable = inc_slip_y
execute_on = timestep_begin
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_x]
type = PenetrationAux
variable = accum_slip_x
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./accum_slip_y]
type = PenetrationAux
variable = accum_slip_y
execute_on = timestep_end
boundary = 4
paired_boundary = 3
[../]
[./penetration]
type = PenetrationAux
variable = penetration
boundary = 4
paired_boundary = 3
[../]
[]
[Postprocessors]
[./bot_react_x]
type = NodalSum
variable = saved_x
boundary = 1
[../]
[./bot_react_y]
type = NodalSum
variable = saved_y
boundary = 1
[../]
[./top_react_x]
type = NodalSum
variable = saved_x
boundary = 5
[../]
[./top_react_y]
type = NodalSum
variable = saved_y
boundary = 5
[../]
[./ref_resid_x]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_x
[../]
[./ref_resid_y]
type = NodalL2Norm
execute_on = timestep_end
variable = saved_y
[../]
[./sigma_yy]
type = ElementAverageValue
variable = stress_yy
[../]
[./sigma_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./disp_x28]
type = NodalVariableValue
nodeid = 27
variable = disp_x
[../]
[./disp_x33]
type = NodalVariableValue
nodeid = 32
variable = disp_x
[../]
[./disp_y28]
type = NodalVariableValue
nodeid = 27
variable = disp_y
[../]
[./disp_y33]
type = NodalVariableValue
nodeid = 32
variable = disp_y
[../]
[./_dt]
type = TimestepSize
[../]
[./num_lin_it]
type = NumLinearIterations
[../]
[./num_nonlin_it]
type = NumNonlinearIterations
[../]
[]
[BCs]
[./bot_y]
type = DirichletBC
variable = disp_y
boundary = 1
value = 0.0
[../]
[./side_x]
type = DirichletBC
variable = disp_x
boundary = 2
value = 0.0
[../]
[./back_z]
type = DirichletBC
variable = disp_z
boundary = 6
value = 0.0
[../]
[./top_press]
type = Pressure
variable = disp_y
boundary = 5
factor = 109.89
[../]
[]
[Materials]
[./bot_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '1'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./bot_strain]
type = ComputeFiniteStrain
block = '1'
[../]
[./bot_stress]
type = ComputeFiniteStrainElasticStress
block = '1'
[../]
[./top_elas_tens]
type = ComputeIsotropicElasticityTensor
block = '2'
youngs_modulus = 1e6
poissons_ratio = 0.3
[../]
[./top_strain]
type = ComputeFiniteStrain
block = '2'
[../]
[./top_stress]
type = ComputeFiniteStrainElasticStress
block = '2'
[../]
[]
[Executioner]
type = Transient
solve_type = 'PJFNK'
petsc_options_iname = '-pc_type -pc_factor_mat_solver_type'
petsc_options_value = 'lu superlu_dist'
line_search = 'none'
nl_abs_tol = 1e-9
nl_rel_tol = 1e-8
l_max_its = 50
nl_max_its = 100
dt = 1.0
end_time = 1.0
num_steps = 10
dtmin = 1.0
l_tol = 1e-5
[]
[VectorPostprocessors]
[./x_disp]
type = NodalValueSampler
variable = disp_x
boundary = '1 3 4 5'
sort_by = id
[../]
[./y_disp]
type = NodalValueSampler
variable = disp_y
boundary = '1 3 4 5'
sort_by = id
[../]
[./cont_press]
type = NodalValueSampler
variable = contact_pressure
boundary = '3'
sort_by = id
[../]
[]
[Outputs]
print_linear_residuals = true
perf_graph = true
[./exodus]
type = Exodus
elemental_as_nodal = true
[../]
[./console]
type = Console
max_rows = 5
[../]
[./chkfile]
type = CSV
show = 'bot_react_x bot_react_y disp_x28 disp_y28 disp_x33 disp_y33 stress_yy stress_zz top_react_x top_react_y x_disp y_disp cont_press'
execute_vector_postprocessors_on = timestep_end
[../]
[./outfile]
type = CSV
delimiter = ' '
execute_vector_postprocessors_on = none
[../]
[]
[Contact]
[./leftright]
secondary = 3
primary = 4
normalize_penalty = true
tangential_tolerance = 1e-3
penalty = 1e+9
[../]
[]
(modules/combined/test/tests/eigenstrain/variable_finite.i)
[Mesh]
type = GeneratedMesh
dim = 2
nx = 10
ny = 10
xmax = 0.5
ymax = 0.5
elem_type = QUAD4
[]
[GlobalParams]
displacements = 'disp_x disp_y'
[]
[Variables]
[./disp_x]
order = FIRST
family = LAGRANGE
[../]
[./disp_y]
order = FIRST
family = LAGRANGE
[../]
[]
[AuxVariables]
[./strain11]
order = CONSTANT
family = MONOMIAL
[../]
[./stress11]
order = CONSTANT
family = MONOMIAL
[../]
[./c]
[../]
[./eigenstrain00]
order = CONSTANT
family = MONOMIAL
[../]
[]
[ICs]
[./c_IC]
int_width = 0.15
x1 = 0
y1 = 0
radius = 0.25
outvalue = 0
variable = c
invalue = 1
type = SmoothCircleIC
[../]
[]
[Kernels]
[./TensorMechanics]
[../]
[]
[AuxKernels]
[./strain11]
type = RankTwoAux
rank_two_tensor = mechanical_strain
index_i = 0
index_j = 0
variable = strain11
[../]
[./stress11]
type = RankTwoAux
rank_two_tensor = mechanical_strain
index_i = 1
index_j = 1
variable = stress11
[../]
[./eigenstrain00]
type = RankTwoAux
variable = eigenstrain00
rank_two_tensor = eigenstrain
index_j = 0
index_i = 0
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
C_ijkl = '1 1'
fill_method = symmetric_isotropic
[../]
[./var_dependence]
type = DerivativeParsedMaterial
block = 0
function = 0.01*c^2
args = c
outputs = exodus
output_properties = 'var_dep'
f_name = var_dep
enable_jit = true
derivative_order = 2
[../]
[./eigenstrain]
type = ComputeVariableEigenstrain
block = 0
eigen_base = '1 1 1 0 0 0'
args = c
prefactor = var_dep
eigenstrain_name = eigenstrain
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y'
eigenstrain_names = eigenstrain
[../]
[./stress]
type = ComputeFiniteStrainElasticStress
block = 0
[../]
[]
[BCs]
[./bottom_y]
type = DirichletBC
variable = disp_y
boundary = bottom
value = 0
[../]
[./left_x]
type = DirichletBC
variable = disp_x
boundary = left
value = 0
[../]
[./top_y]
type = FunctionDirichletBC
variable = disp_y
boundary = top
function = 0.0005*t
[../]
[]
[Preconditioning]
[./SMP]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
num_steps = 3
solve_type = PJFNK
petsc_options_iname = '-pc_type '
petsc_options_value = lu
l_max_its = 20
nl_max_its = 10
l_tol = 1.0e-4
nl_rel_tol = 1.0e-8
nl_abs_tol = 1.0e-9
reset_dt = true
[]
[Outputs]
execute_on = 'timestep_end'
exodus = true
[]
(modules/tensor_mechanics/test/tests/crystal_plasticity/user_object_based/linesearch.i)
[Mesh]
type = GeneratedMesh
dim = 3
elem_type = HEX8
displacements = 'ux uy uz'
[]
[Variables]
[./ux]
[../]
[./uy]
[../]
[./uz]
[../]
[]
[AuxVariables]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./fp_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./e_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./gss]
order = CONSTANT
family = MONOMIAL
[../]
[]
[Functions]
[./tdisp]
type = ParsedFunction
value = 0.01*t
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'ux uy uz'
use_displaced_mesh = true
[../]
[]
[AuxKernels]
[./stress_zz]
type = RankTwoAux
variable = stress_zz
rank_two_tensor = stress
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./fp_zz]
type = RankTwoAux
variable = fp_zz
rank_two_tensor = fp
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./e_zz]
type = RankTwoAux
variable = e_zz
rank_two_tensor = lage
index_j = 2
index_i = 2
execute_on = timestep_end
[../]
[./gss1]
type = MaterialStdVectorAux
variable = gss
property = state_var_gss
index = 0
execute_on = timestep_end
[../]
[]
[BCs]
[./symmy]
type = DirichletBC
variable = uy
boundary = bottom
value = 0
[../]
[./symmx]
type = DirichletBC
variable = ux
boundary = left
value = 0
[../]
[./symmz]
type = DirichletBC
variable = uz
boundary = back
value = 0
[../]
[./tdisp]
type = FunctionDirichletBC
variable = uz
boundary = front
function = tdisp
[../]
[]
[UserObjects]
[./slip_rate_gss]
type = CrystalPlasticitySlipRateGSS
variable_size = 12
slip_sys_file_name = input_slip_sys.txt
num_slip_sys_flowrate_props = 2
flowprops = '1 4 0.001 0.1 5 8 0.001 0.1 9 12 0.001 0.1'
uo_state_var_name = state_var_gss
[../]
[./slip_resistance_gss]
type = CrystalPlasticitySlipResistanceGSS
variable_size = 12
uo_state_var_name = state_var_gss
[../]
[./state_var_gss]
type = CrystalPlasticityStateVariable
variable_size = 12
groups = '0 4 8 12'
group_values = '60.8 60.8 60.8'
uo_state_var_evol_rate_comp_name = state_var_evol_rate_comp_gss
scale_factor = 1.0
[../]
[./state_var_evol_rate_comp_gss]
type = CrystalPlasticityStateVarRateComponentGSS
variable_size = 12
hprops = '1.0 541.5 109.8 2.5'
uo_slip_rate_name = slip_rate_gss
uo_state_var_name = state_var_gss
[../]
[]
[Materials]
[./crysp]
type = FiniteStrainUObasedCP
stol = 1e-2
tan_mod_type = exact
maximum_substep_iteration = 200
use_line_search = true
min_line_search_step_size = 0.01
uo_slip_rates = 'slip_rate_gss'
uo_slip_resistances = 'slip_resistance_gss'
uo_state_vars = 'state_var_gss'
uo_state_var_evol_rate_comps = 'state_var_evol_rate_comp_gss'
[../]
[./strain]
type = ComputeFiniteStrain
displacements = 'ux uy uz'
[../]
[./elasticity_tensor]
type = ComputeElasticityTensorCP
C_ijkl = '1.684e5 1.214e5 1.214e5 1.684e5 1.214e5 1.684e5 0.754e5 0.754e5 0.754e5'
fill_method = symmetric9
[../]
[]
[Postprocessors]
[./stress_zz]
type = ElementAverageValue
variable = stress_zz
[../]
[./fp_zz]
type = ElementAverageValue
variable = fp_zz
[../]
[./e_zz]
type = ElementAverageValue
variable = e_zz
[../]
[./gss]
type = ElementAverageValue
variable = gss
[../]
[]
[Preconditioning]
[./smp]
type = SMP
full = true
[../]
[]
[Executioner]
type = Transient
dt = 0.05
solve_type = 'PJFNK'
petsc_options_iname = -pc_hypre_type
petsc_options_value = boomerang
nl_abs_tol = 1e-10
nl_rel_step_tol = 1e-10
dtmax = 10.0
nl_rel_tol = 1e-10
end_time = 1
dtmin = 0.02
num_steps = 10
nl_abs_step_tol = 1e-10
[]
[Outputs]
exodus = true
[]
(modules/tensor_mechanics/test/tests/j2_plasticity/hard2.i)
# UserObject J2 test, with hardening, but with rate=1E6
# apply uniform compression in x direction to give
# trial stress_xx = 5, so sqrt(3*J2) = 5
# with zero Poisson's ratio, lambda_mu = 1E6, and strength=2, strength_residual=1,
# the equations that we need to solve are:
#
# stress_yy = stress_zz [because of the symmetry of the problem: to keep Lode angle constant]
# stress_xx - stress_yy = 1 + (2 - 1)*exp(-0.5*(1E6*q)^2) [yield_fcn = 0]
# stress_xx + stress_yy + stress_zz = 5 [mean stress constant]
# q = gamma
# stress_xx = 1E6*2*gamma*(stress_xx - 5/3)*sqrt(3)/2/sqrt(J2), where sqrt(J2) = (1 + (2 - 1)*exp(-0.5*(1E6*q)^2))/Sqrt(3)
# so RHS = 1E6*2*gamma*(stress_xx - 5/3)*3/2/(stress_xx - stress_yy)
#
# stress_xx = 2.672
# stress_yy = 1.164
# q = 1.164E-6
[Mesh]
type = GeneratedMesh
dim = 3
nx = 1
ny = 1
nz = 1
xmin = -0.5
xmax = 0.5
ymin = -0.5
ymax = 0.5
zmin = -0.5
zmax = 0.5
[]
[Variables]
[./disp_x]
[../]
[./disp_y]
[../]
[./disp_z]
[../]
[]
[Kernels]
[./TensorMechanics]
displacements = 'disp_x disp_y disp_z'
[../]
[]
[BCs]
[./x]
type = FunctionDirichletBC
variable = disp_x
boundary = 'front back'
function = '2.5E-6*x'
[../]
[./y]
type = FunctionDirichletBC
variable = disp_y
boundary = 'front back'
function = '0E-6*y'
[../]
[./z]
type = FunctionDirichletBC
variable = disp_z
boundary = 'front back'
function = '0E-6*z'
[../]
[]
[AuxVariables]
[./stress_xx]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_xz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yy]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_yz]
order = CONSTANT
family = MONOMIAL
[../]
[./stress_zz]
order = CONSTANT
family = MONOMIAL
[../]
[./f]
order = CONSTANT
family = MONOMIAL
[../]
[./iter]
order = CONSTANT
family = MONOMIAL
[../]
[./intnl]
order = CONSTANT
family = MONOMIAL
[../]
[]
[AuxKernels]
[./stress_xx]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xx
index_i = 0
index_j = 0
[../]
[./stress_xy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xy
index_i = 0
index_j = 1
[../]
[./stress_xz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_xz
index_i = 0
index_j = 2
[../]
[./stress_yy]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yy
index_i = 1
index_j = 1
[../]
[./stress_yz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_yz
index_i = 1
index_j = 2
[../]
[./stress_zz]
type = RankTwoAux
rank_two_tensor = stress
variable = stress_zz
index_i = 2
index_j = 2
[../]
[./f]
type = MaterialStdVectorAux
index = 0
property = plastic_yield_function
variable = f
[../]
[./iter]
type = MaterialRealAux
property = plastic_NR_iterations
variable = iter
[../]
[./intnl]
type = MaterialStdVectorAux
index = 0
property = plastic_internal_parameter
variable = intnl
[../]
[]
[Postprocessors]
[./s_xx]
type = PointValue
point = '0 0 0'
variable = stress_xx
[../]
[./s_xy]
type = PointValue
point = '0 0 0'
variable = stress_xy
[../]
[./s_xz]
type = PointValue
point = '0 0 0'
variable = stress_xz
[../]
[./s_yy]
type = PointValue
point = '0 0 0'
variable = stress_yy
[../]
[./s_yz]
type = PointValue
point = '0 0 0'
variable = stress_yz
[../]
[./s_zz]
type = PointValue
point = '0 0 0'
variable = stress_zz
[../]
[./f]
type = PointValue
point = '0 0 0'
variable = f
[../]
[./iter]
type = PointValue
point = '0 0 0'
variable = iter
[../]
[./intnl]
type = PointValue
point = '0 0 0'
variable = intnl
[../]
[]
[UserObjects]
[./str]
type = TensorMechanicsHardeningGaussian
value_0 = 2
value_residual = 1
rate = 1E12
[../]
[./j2]
type = TensorMechanicsPlasticJ2
yield_strength = str
yield_function_tolerance = 1E-5
internal_constraint_tolerance = 1E-9
[../]
[]
[Materials]
[./elasticity_tensor]
type = ComputeElasticityTensor
block = 0
fill_method = symmetric_isotropic
C_ijkl = '0 1E6'
[../]
[./strain]
type = ComputeFiniteStrain
block = 0
displacements = 'disp_x disp_y disp_z'
[../]
[./mc]
type = ComputeMultiPlasticityStress
block = 0
ep_plastic_tolerance = 1E-9
plastic_models = j2
debug_fspb = crash
[../]
[]
[Executioner]
end_time = 1
dt = 1
type = Transient
[]
[Outputs]
file_base = hard2
exodus = false
[./csv]
type = CSV
[../]
[]
(modules/tensor_mechanics/include/materials/ComputeRSphericalFiniteStrain.h)
// This file is part of the MOOSE framework
// https://www.mooseframework.org
//
// All rights reserved, see COPYRIGHT for full restrictions
// https://github.com/idaholab/moose/blob/master/COPYRIGHT
//
// Licensed under LGPL 2.1, please see LICENSE for details
// https://www.gnu.org/licenses/lgpl-2.1.html
#pragma once
#include "ComputeFiniteStrain.h"
/**
* ComputeRSphericalFiniteStrain defines a strain increment and a rotation increment
* for finite strains in 1D spherical symmetry geometries. The strains in the
* polar and azimuthal directions are functions of the radial displacement.
*/
class ComputeRSphericalFiniteStrain : public ComputeFiniteStrain
{
public:
static InputParameters validParams();
ComputeRSphericalFiniteStrain(const InputParameters & parameters);
virtual void initialSetup() override;
/// Computes the current and old deformation gradients with the assumptions for
/// 1D spherical symmetry geometries: \f$ \epsilon_{\theta} = \epsilon_{\phi} = \frac{u_r}{r} \f$
virtual void computeProperties() override;
protected:
virtual void computeQpIncrements(RankTwoTensor & e, RankTwoTensor & r) override;
/// the old value of the first component of the displacements vector
const VariableValue & _disp_old_0;
};
(modules/tensor_mechanics/include/materials/Compute1DFiniteStrain.h)
// This file is part of the MOOSE framework
// https://www.mooseframework.org
//
// All rights reserved, see COPYRIGHT for full restrictions
// https://github.com/idaholab/moose/blob/master/COPYRIGHT
//
// Licensed under LGPL 2.1, please see LICENSE for details
// https://www.gnu.org/licenses/lgpl-2.1.html
#pragma once
#include "ComputeFiniteStrain.h"
/**
* Compute1DFiniteStrain defines a strain increment for finite strains in 1D problems,
* handling strains in other two directions. It contains virtual methods to define
* the displacement gradients as a general nonzero value.
*/
class Compute1DFiniteStrain : public ComputeFiniteStrain
{
public:
static InputParameters validParams();
Compute1DFiniteStrain(const InputParameters & parameters);
void computeProperties() override;
protected:
/// Computes the current dUy/dY; as a virtual function, this function is
/// overwritten for the specific geometries defined by inheriting classes
virtual Real computeGradDispYY() = 0;
/// Computes the old dUy/dY; as a virtual function, this function is
/// overwritten for the specific geometries defined by inheriting classes
virtual Real computeGradDispYYOld() = 0;
/// Computes the current dUz/dz; as a virtual function, this function is
/// overwritten for the specific geometries defined by inheriting classes
virtual Real computeGradDispZZ() = 0;
/// Computes the old dUz/dz; as a virtual function, this function is
/// overwritten for the specific geometries defined by inheriting classes
virtual Real computeGradDispZZOld() = 0;
};
(modules/tensor_mechanics/include/materials/Compute2DFiniteStrain.h)
// This file is part of the MOOSE framework
// https://www.mooseframework.org
//
// All rights reserved, see COPYRIGHT for full restrictions
// https://github.com/idaholab/moose/blob/master/COPYRIGHT
//
// Licensed under LGPL 2.1, please see LICENSE for details
// https://www.gnu.org/licenses/lgpl-2.1.html
#pragma once
#include "ComputeFiniteStrain.h"
/**
* Compute2DFiniteStrain defines a strain increment and a rotation increment
* for finite strains in 2D geometries, handling the out of plane strains.
* Compute2DFiniteStrain contains a virtual method to define the out-of-plane strain
* as a general nonzero value in the inherited classes ComputePlaneFiniteStrain
* and ComputeAxisymmetricRZFiniteStrain.
*/
class Compute2DFiniteStrain : public ComputeFiniteStrain
{
public:
static InputParameters validParams();
Compute2DFiniteStrain(const InputParameters & parameters);
void initialSetup() override;
virtual void computeProperties() override;
protected:
virtual void displacementIntegrityCheck() override;
/**
* Computes the current out-of-plane component of the displacement gradient; as a virtual
*function, this function is overwritten for the specific geometries defined by inheriting classes
*/
virtual Real computeOutOfPlaneGradDisp() = 0;
/**
* Computes the old out-of-plane component of the displacement gradient; as a virtual function,
* this function is overwritten for the specific geometries defined by inheriting classes
*/
virtual Real computeOutOfPlaneGradDispOld() = 0;
const unsigned int _out_of_plane_direction;
};